• Geophysics and Geophysical Exploration
• /
• v.11 no.4
• /
• pp.286-301
• /
• 2008

When magnetotelluric (MT) data are obtained in vicinity of the coast, the sea can distort observed MT responses, especially those of deep part of subsurface. We introduce an iterative method to correct the sea effect, based on the previous topographic correction method which removes the distortions due to topographic changes in seafloor MT data. The method first corrects the sea effect in observed MT impedance, and then inverts corrected responses in a model space without the sea. Due to mutual coupling between sea and subsurface structure, the correction and inversion steps are iterated until changes in each result become negligible. The method is validated for 1-D and 2-D structure using synthetic MT data produced by 3-D forward modeling including surrounding seas. In all cases, the method closely recovers the given structure after a few iterations. To test the applicability of the proposed method to field data, we generate synthetic MT data for the Jeju Island whose 1-D conductivity structure is well known, using 3-D forward modeling. The distortions due to the surrounding sea start to appear below the frequency about 1 Hz, and are relatively severe in the electrical field perpendicular to the coastline because of the location of the observation sites. The proposed method successfully eliminates the sea effect after three iterations, and both 1-D and 2-D inversion of corrected responses closely recover the given subsurface structure of the Jeju Island model.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2012.07a
• /
• pp.417-418
• /
• 2012

본 논문에서는 3차원 데이터를 이용한 효율적인 실내 공간 표현 기법을 제안한다. 제안하는 기법은 3차원 데이터의 획득과 실내 구조 및 영상 정보를 표현하기 위한 표현 복원으로 구성된다. 3차원 데이터는 레이저 거리 측정기(laser range finder, LRF)와 전방향(omni) 카메라를 통해 획득한 포인트 클라우드 공간 정보와 전방향 텍스쳐 영상으로 구성된다. 실내 구조를 복원하기 위해, 획득한 포인트 클라우드를 복셀 격자 기반의 샘플링 기법을 통해 균일화하고 포아송 표면 재구성(Poisson surface rocoostruction) 기법을 통해 3차원 메쉬를 생성한다. 그리고 전방향 텍스쳐 영상과 3차원 메쉬외 기하학적 관계를 이용한 텍스쳐 매핑 기법을 통해 최종적으로 3차원 메쉬 표면을 복원한다. 실험 결과를 통해 제안하는 기법이 실내 공간을 효과적으로 표현함을 확인한다.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.10c
• /
• pp.265-267
• /
• 2004

애드 혹 네트워크에서 이동 모델은 가장 중요한 요인 중 하나이다. 또한 실험의 어려움 때문에 시뮬레이션을 통한 성능 명가가 애드 혹 네트워크에서는 꼭 필요하다. 하지만 현재 존재하는 애드 혹 네트워크 시뮬레이션에서는 3 차원 이동 환경이 전혀 고려되지 않은 이동 모델을 사용하고 있다. 즉 현재의 시뮬레이션 이동 모델은 3차원에서 이동 하는 실제의 이동 형태를 정확하게 반영 못하고 있다. 본 논문에서는 장애물 까지 포함하는 좀더 현실적인 3차원 이동 모델을 제시하고, 그것의 시뮬레이션 방법을 제시 한다. 3DMG를 통해 3차원 이동 정보와 장애물 정보를 만들고, 그러한 정보를 Glomosim 시뮬레이션 툴에 입력하여, 3차원 이동 모델에 따른 시뮬레이션이 가능하게 만들었다. 또한 본 논문에서는 이러한 방법에 의한 예제 시뮬레이션을 보여주며, 이를 통해 3차원 이동 모델의 효과를 보여준다.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.4
• /
• pp.310-318
• /
• 2016

This study deals with a method to localize a noise source occuring in a marine vehicle in a 3D environment. Even when access to the noise source is limited for a marine vehicle, such as a ship or a submarine in operation, the signal received on a hydrophone located elsewhere contains Doppler effected noise by moving relatively. This study suggests noise localization algorithm in 3D based on Doppler effect by moving marine vehicle. Using a known source mounted on the vehicle, the noise source was estimated by reducing the range of Doppler center and closest point of approach via the least square method. The algorithm was verified through various simulations and it was shown that the noise could be localized in 3D based on Doppler effect by employing two fixed hydrophones located at the vehicle's exterior points and a known reference signal generator located somewhere on the vehicle.

• Spatial Information Research
• /
• v.20 no.4
• /
• pp.29-36
• /
• 2012

The low-carbon freight transportation system was introduced due to increase traffic congestion cost and carbon-dioxide for global climate change according to expanding city logistics demands. It is necessary to create 3D-based road network map for representing realistic road geometry with consideration of fuel consumption and carbon emissions. This study propose that 3D road network model expressed to realistic topography and road structure within trunk road for intercity freight through overlaying 2D-based transport-related thematic map and 1m-resolution DEM. The 3D-based road network map for the experimental road sections(Pyeongtaek harbor-Uiwang IC) was verified by GPS/INS survey and fuel consumption simulation. The results corresponded to effectively reflect realistic road geometry (RMSE=0.87m) except some complex structure such as overpass, and also actual fuel consumption. We expect that Green-based freight route planning and navigation system reflected on 3D geometry of complex road structure will be developed for effectively resolving energy and environmental problems.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.05a
• /
• pp.55-58
• /
• 2005

Low resistivity zone is observed at the lower part of a CFRD (Concrete Face Rockfill Dam). Generally, CFRD tends not to have any saturated zone within the body, but the result of resistivity survey shows that it is possible for the dam to be saturated under 20m depth with water. The level of reservoir was under 10m from the crest. We suspect that this result may come from the wrong 2D inversion process ignoring the 3D geometry of dams. For the analysis of possibility of distortion by different geometry, we perform the 3D forward modeling for the dam and apply the 2D inversion process. And then we check the point of traditional interpretation of resistivity data. By the analysis, it is found that the result of 2D inversion process of 3D geometry of dams, seems to have deep relation with the reservoir level, and the complex 3D structure hide some internal electrical anomaly of dams from resistivity information.

• Journal of the Korean Geophysical Society
• /
• v.8 no.4
• /
• pp.211-214
• /
• 2005

Low resistivity zone is observed at the lower part of a CFRD (Concrete Face Rockfill Dam). Generally, CFRD tends not to have any saturated zone within the body, but the result of resistivity survey shows that it is possible for the dam to be saturated under 20m depth with water. The level of reservoir was under 10 m from the crest. We suspect that this result may come from the wrong 2D inversion process ignoring the 3D geometry of dams. For the analysis of possibility of distortion by different geometry, we perform the 3D forward modeling for the dam and apply the 2D inversion process. And then we check the point of traditional interpretation of resistivity data. By the analysis, it is found that the result of 2D inversion process of 3D geometry of dams, seems to have deep relation with the reservoir level, and the complex 3D structure hide some internal electrical anomaly of dams from resistivity information.

• Information and Communications Magazine
• /
• v.32 no.2
• /
• pp.98-107
• /
• 2015

본 고에서는 3차원 동영상에서 움직임 정보 추출하고 이를 이용하여 홀로그램 콘텐츠를 효과적으로 생성하는 방법들에 대해 알아본다.

• The Journal of Engineering Geology
• /
• v.14 no.1
• /
• pp.21-28
• /
• 2004

Three-dimensional (3-D) resistivity inversion including a topographic effect can be considered theoretically to be the technique of acquiring the most accurate image in the interpretation of resistivity data, because it includes characteristic image that the actual subsurface structure is 3-D. In this study, a finite-element method was used as the numerical method in modeling, and the efficiency of Jacobian calculation has been maximized with sensitivity analysis for the destination block in inversion process. Also, during the iterative inversion, the resolution of inversion can be improved with the method of selecting the optimal value of Lagrange multiplier yielding minimum RMS(root mean square) error in the parabolic equation. In this paper, we present synthetic examples to compare the difference between the case which has the toprographic effect and the other case which has not the effect in the inversion process.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2000.04a
• /
• pp.409-413
• /
• 2000

본 논문은 가상현실의 한 분야인 VRML 저작도구의 설계와 구현에 고나하여 기술하였다. 가장 효과적인 장면생성과 Graphic Library (OpengL)와 VRML Noderks의 매칭 구현을 통하여 Objects 의 Rendering 수준을 한 차원 높이고, COM 기반의 Parser 사용으로 저작도구 구현에 효율성과 재사용성을 극대화하며, 3차원 모델링을 모다 손쉽게 저작할수 있는 저작도구를 구현하였다. 3차원 모델링 기술의 기반 구조가 취약한 국내에서 이 분야 기술력의 축적과 함께 3차원 모델링 기술을 이용한 응용 제품 개발의 저변확대와 다양한 유형의 쇼핑몰 구현 기반 기술 확보등의 효과를 거둘 수 있다.