• 한국안전학회지
• /
• 제34권5호
• /
• pp.103-110
• /
• 2019

In order to reduce the accidents occurring at construction sites, it is necessary to approach with harmonious measures considering various aspects such as systems, training, facilities, and protection equipments. Suggestion of safe construction method can be a good alternative. In the previous study, the half-depth precast deck with RC rib panel was proposed as an alternative method for safe bridge deck construction, and the performance required by the design code was verified through a four-point bending test. But the actual bridge deck is subjected to the repetitive action of the wheel load rather than the bending condition due to the four-point load. In this study, fatigue test was performed by repeating the wheel load $2{\times}10^6$ cycles to verify the safety of the half-depth precast deck with RC rib panel under actual conditions. As a result, fatigue effect due to repetition of wheel load was not significant in terms of serviceability such as crack width and deflection. In the residual strength test conducted after the fatigue test, the half-depth precast deck with RC rib panel failed by punching shear which is typical failure mode of bridge decks and the residual strength was similar to the punching strength of the RC and PSC bridge decks in spite of the fatigue effects.

• 한국분말재료학회지
• /
• 제25권6호
• /
• pp.501-506
• /
• 2018

With the recent remarkable improvements in the average speeds of contemporary trains, a necessity has arisen for the development of new friction modifiers to improve adhesion characteristics at the wheel-rail interface. The friction modifier must be designed to reduce slippage or sliding of the trains' wheels on the rails under conditions of rapid acceleration or braking without excessive rolling contact wear. In this study, a novel composite material consisting of metal, ceramic, and polymer is proposed as a friction modifier to improve adhesion between wheels and rails. A blend of Al-6Cu-0.5Mg metallic powder, $Al_2O_3$ ceramic powder, and Bakelite-based polymer in various weight-fractions is hot-pressed at $150^{\circ}C$ to form a bulk composite material. Variation in the adhesion coefficient is evaluated using a high-speed wheel-rail friction tester, with and without application of the composite friction modifier, under both dry and wet conditions. The effect of varying the weighting fractions of metal and ceramic friction powders is detailed in the paper.

• 한국기계가공학회지
• /
• 제21권3호
• /
• pp.77-85
• /
• 2022

In this study, to diagnose the grinding state of a micro drill bit, a sensor attachment location was selected through random vibration analysis of the grinding unit of the micro drill-bit grinding system. In addition, the vibration data generated during the drill bit grinding were collected from the grinding unit for the grinding wheels under the steady and worn conditions, and data feature extraction and dimension reduction were performed. The wear of the micro-drill-bit grinding wheel was diagnosed by applying KNN, a machine-learning algorithm. The classification model showed excellent performance, with an accuracy of 99.2%. The precision, recall and f1-score were higher than 99% in both the steady and wear conditions.

• 한국세라믹학회지
• /
• 제51권4호
• /
• pp.317-323
• /
• 2014

People could not imagine living without tab water. However, the water filtering process at a purification plant used to produce tab water creates tons of sludge, which is generally wasted. This sludge waste consists of (1) mineral elements, such as sand, (2) organic materials, and (3) a coagulant, which agglomerates the two. As an enormous amount of sludge waste is generated every year, numerous studies have been carried out to identify how to deal with this problem. Currently, however, most of the sludge waste is directly discarded in landfills. In the present study, water-purified sludge waste received a heat treatment at $1300^{\circ}C$ and was then ground into particles to be used as a ceramic material. Next, the resultant particles were compounded with chamotte substitutes to produce grogged clay that is suitable for wheel-throwing ceramics. Consequently, the plasticity of the sludge waste decreased as the content of calcination increased. Thus, it is considered that wheel throwing is available only up to PBF-3. Thus, it is available for wheel throwing and has a high strength of 864 $kgf/cm^2$ with less than 0.2 percent of porosity and absorption ratio were displayed in PBF-2 at $1280^{\circ}C$ with 20 percent of calcination from the purified sludge. Therefore, the PBF-2 body produced in this study was considered to be capable of replacing grogged clay in the market.

• 한국기계가공학회지
• /
• 제7권2호
• /
• pp.45-51
• /
• 2008

The objective of this study is to develop an automatic object changer unit to improve processing problems existed in the conventional horizontal machining center. In order to perform this objective, a upward and downward traverse unit in which a unit that consists of a motor and reducer, chain and sprocket wheel, and upper and lower base employed in an automatic object changer unit performs sliding contact motion in a frame was designed. To achieve this design, constraint conditions for the upward and downward traverse unit first designed. Then, an operation mechanism was designed and that was introduced as a sum of kinetic energy for the sprocket wheel and upper and lower base based on the moment of inertia, which is the kinetic energy of the converted upward and downward traverse unit in the side of the reducer. In addition, The work required to rotate the converted upward and downward traverse unit in the side of the reducer by one revolution can be calculated using the sum of work that is required in the sprocket wheel and upper and lower base that is a part of the upward and downward traverse unit. Furthermore, the converted equation of motion in the side of the motor can be introduced using the equation of motion using the converted upward and downward traverse unit in the side of the motor. Then, Then, a proper motor can be determined using predetermined specifications employed in the motor and several parameters in the upward and downward traverse unit in order to verify such predetermined specifications. Also, a design of a horizontal traverse unit that performs sliding motion on a upward and downward traverse unit and simulation that verifies the results of this design are required as a future study.

• 비파괴검사학회지
• /
• 제28권2호
• /
• pp.125-130
• /
• 2008

레이저 용접부의 국소 잔류응력을 측정하기 위한 비파괴 기법으로 구형압입시험이 제안되었다. 용접상태 절단휠의 구형압입시험으로 얻어진 겉보기 항복강도와 절단횔 용접부에 대한 응력완화 열처리 이후 동등한 위치에서 구한 고유 항복강도를 정량적으로 비교하였다. 고유항복강도가 탄성한도 내의 잔류응력에 의해서 변화하지 않는다고 고려하면 용융선으로부터 거리에 따른 두 항복강도의 차이가 용접잔류응력의 분포로 나타난다. 레이저 용접된 다이아몬드 절단휠의 구형압입시험으로부터 약 10 mm 폭에 걸친 잔류응력의 분포를 확인하였으며, 잔류응력은 쌩크와 절단팁 내에서 각각 최대 압축 및 인장 잔류응력치를 나타내었다.

• 대한산업공학회지
• /
• 제35권2호
• /
• pp.141-149
• /
• 2009

As the number of personal computers installed in vehicles increases, a touchpad often used in a labtop computer can be used for the control of an in-vehicle information system (IVIS). Using a touchpad to control the system allows the user to select among large amount of information with a single touch of dragging. For safety and convenience of a driver, the touchpad could be placed on a steering wheel. This research is designed to calculate the most efficient Control-Response Ratio (C/R ratio) for the menu interaction of a touchpad on a steering wheel. Since the menu pointer's rate of movement and proper C/R ratio is determined by the amount of selected information, the amount of displayed information and the movement of a menu pointer was chosen to be independent variables. The dependent variables are a user's preference and task completion time. Two factor full factorial within subject design was used 16 subjects. The investigation revealed that the amount of selected information increased with increasing C/R ratio. The movement of the pointer became slower as the amount of information increased. The best C/R ratio was calculated for each amount of information and preference regression of the user's preference was drawn accordingly. Through this research, the automobile interior designer can benefit from the guidelines suggested for the touchpad control.

• 해양환경안전학회지
• /
• 제13권2호
• /
• pp.161-167
• /
• 2007

이 논문은 선박의 자동조타장치를 음성인식으로 제어할 수 있는 시스템을 개발하기 위한 기초연구로 SMCP(IMO Standard Marine Communication Phrases)에 제시된 조타명령문의 구성 형태를 분석하여 화자의 의도를 예측할 수 있는 특정 파라미터를 추출하였다. 그리고 이 파라미터를 이용하여 1차 패턴인식 과정으로부터 도출된 후보단어 집합으로부터 최종 단어를 결정하는 후처리 인식 프로시저를 설계하였다. 이 프로시저의 유용성을 검증하기 위하여 음성인식용으로 총 525개의 조타명령문을 획득하였고, 표준패턴 기반의 인식과정 인식률과의 비교실험을 수행하였다. 실험결과 의도예측 특정 파라미터를 이용한 인식 프로시저의 인식률이 약 42.3% 향상되어 유효함을 알 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2009년도 춘계 학술논문 발표대회 학계
• /
• pp.247-252
• /
• 2009

The LMC method of construction which have application to the road bridge is being considered the least relative importance about the watertight performance, because it focused on the durability of concrete. However, The LMC which is being expanded scope of application to the method of construction has grown importance about the watertight performance on the usability and maintenance side as well as durability. In this study, The latex concrete of two types which are different from mingled-ratio of the latex made a comparison to the compressive strength, watertight performance, dynamic wheel load resistance performance and confirmed what it has resistibility about chemical action through the chemical resistance test. The initial strength and watertight performance showed that were tendency the downward at 14 days. However, The long-term strength after 28 days showed that it has firm performance. In consequence, The initial curing of latex concrete is required to scrupulous care and attention at the site application. As a chemical resistance test result, The specimen that is steeped in sulphuric acid solution of 2% discovered the delamination phenomenon. However, it was confirmed that delamination phenomenon don't have an effect on the compressive strength. Moreover, As a dynamic wheel load resistance test result, The latex concrete was concluded to confirming the durability and running stability, because it had hardly any thickness reduction of latex concrete surface about dynamic wheel load and rarely found crack and delamination.

• 한국전산구조공학회논문집
• /
• 제33권2호
• /
• pp.121-128
• /
• 2020

본 논문에서는 고속열차-차륜-레일-지반부의 상호작용에 따른 지반부의 변위장과 가속도장의 분포양상을 연구하고자 하였다. 이를 위해 고속열차 주행을 실제 차륜으로 모형하여 차륜-레일간의 연직접촉과 사행동에 의한 횡접촉을 모사하고, 이동질량해석을 근간으로 하였다. 이 때 지반부는 Modified Drucker-Prager 모델을 이용하여 상면 지반부의 비선형 거동을 부여하고 이에 따른 변위, 가속도의 변화를 탄성지반의 거동과 비탄성지반의 거동을 상호 비교하였다. 이를 통해, 실제 지반거동과 가까운 변위와 가속도 범위를 예측하고자 하였다. 이 때 지반부의 von-Mises응력과 등가소성변형도를 검토하고, 각 파괴면에서의 등가소성변형도, 전체 체적변형도 등을 검토하였다. 이동질량을 이용한 차륜-레일 접촉부의 수직응력, 횡압, 종방향 구속압 등의 시간이력에 따른 응력변화도 검토하였다. 비선형 지반모델의 경우 탄성 지반모델에 비해 열차 주행에 따른 변위 차이는 크지 않는 반면에 가속도의 경우는 큰 감소를 발생시키는 것으로 나타났다.