• Magazine of the Korean Society of Agricultural Engineers
• /
• v.16 no.4
• /
• pp.3572-3584
• /
• 1974

본 논문은 Thrower의 양곡성능에 관한 예측 방정식을 차원해석법을 적용하여 유도하는데 있다. Thrower의 능률에 큰 영향을 미친다고 생각되는 인자들간의 관계식들을 Buckingham의 $\pi$이론에 의하여 구하여 졌으며 본연구에 사용한 Thrower는 현재 농촌에서 사용되고 있는 자동탈곡기의 Thrower와 유사한 형으로 제작된 것이며 실험에 사용된 시료는 벼의 경우는 통일벼와 미네히까리 품종이고 보리 품종으로서는 나맥이며, Thrower의 Impeller 직경, 속도 및 투입량을 변화시켜 가면서 각 시료에 대하여 양곡높이를 측정하여 그 예측방정식을 유도하였다. 본 논문에서 얻은 결과는 다음과 같다. 1. Thrower의 양곡성능에 지대한 영향을 미친다고 생각되는 주요 인자들을 Thrower의 양정, impeller의 직경과 속도, 투입량, 곡립의 밀도, 중력가속도등이라 간주하여 Buckingham의 $\pi$이론을 적용하여 이들에 관한 $\pi$항들을 결정하였으며 그 결과는 다음과 같다. {{{{ pi 1= { D} over {H } , pi 2= { { DN}^{ { 1} over {2 } } } over { { g}^{ { 1} over { 2} } }, pi 3= { Q} over { { g}^{ { 1} over {2 } } { rho D}^{ { 2} over {6 } } }}}}} 2. 실험에 의하여 구해진 $\pi$항문의 관계식을 합성하여 Thrower의 양곡성능에 관한 시료별 예측방정식을 구하였으며 이 식들은 아래와 같다. 통일 : $\pi$1=0.1223($\pi$2)-1.1813$\times$($\pi$3)-0.1864 미네히까리 : $\pi$1=0.1185($\pi$2)-0.9663$\times$($\pi$3)-0.1575 나맥 : $\pi$1=0.1599($\pi$2)-1.2350$\times$($\pi$3)-0.1382 3. 현재 농촌에서 사용되고 있는 자동탈곡기체 부착된 Thrower의 회전수, Impeller의 직경 및 투입량은 각각 1,100rpm, 30cm 및 150gr/sec 정도로서 이와같은 수준의 변량들을 기초로 하여 본 논문에서 유도한 예측방정식을 적용하여 Thrower의 양정을 산출한 결과, 통일벼의 경우는 2.6m정도였고 미네히까리 품종과 나맥의 양정은 각각 2.4m, 2.9m 정도였다. 이와같은 사실로부터 1m내외의 양정만으로 되어있는 자동탈곡기 Thrower의 경우 제작비절감, 소요동력 감소를 기하고 아울러 과립의 손상을 줄이기 위해서는 설계 또는 작동조건의 변경을 통해 Thrower의 회전수를 현재 수준이하로 줄일 필요가 있다고 판단되었다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.1
• /
• pp.104-111
• /
• 2017

This research focuses on simulation and visualization of flow field characteristics inside a centrifugal pump. The 3D numerical analysis was carried out by using a numerical CFD tool, addressing a Reynolds Average Navier-Stock code with a standard k-${\varepsilon}$ two-equation turbulence model. The simulation accounts for friction head loss due to rough walls at suction, impeller, discharge areas and volumetric head loss at impeller wear ring. A comparison of performance curves between simulation and experimentation is included, and it reveals a same trend of those results with a small difference of maximum 5 %. At best efficiency point, velocity vectors are smooth but it changes significantly under off-design point, a strong recirculation appears at the outlet of impeller passages near tongue area. A relatively uniform preassure distribution was observed around the impeller in despite of the tongue. Within the volute, because of its geometry, spiral vortexes formed, proving that the flow field in this region was relatively turbulent and unsteady.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.4
• /
• pp.29-38
• /
• 2007

In this study, flow structure in a two-stage centrifugal compressor for a turbo-chiller with the refrigerant, R134a, was numerically investigated at the design point of the compressor using a commercial code. Flow characteristics in the passages of impeller, diffuser and return channel were analyzed in detail including velocity vector, secondary flow, Mach number and pressure contours in blade spanwise and meridional plane for each stage. The estimation on the one-dimensional output from the preliminary design and three-dimensional shape of the impeller blade and the meridional shape of the return channel were performed through the flow analysis, while some numerical schemes and techniques including Multiple Frames of Reference technique, real gas property data and inlet boundary condition changes, which were used in CFD, were compared with their features. The results will be used as reference data for a new design of 3-D impeller shape to improve R134a compressor performance.

• Journal of computational fluids engineering
• /
• v.21 no.1
• /
• pp.58-63
• /
• 2016

This research is to investigate the performance analysis for efficient design with four different inlet angles of the centrifugal pump impeller. Assuming that the rotation speed and exit angle are fixed, Four cases of the centrifugal pumps were numerically analyzed using ANSYS FLUENT. According to the numerical results, head and pump efficiency at inlet angle of 20 degrees was highest. There is no big difference of efficiency at inlet angle of 20 degrees compared to the inlet angle 30 degrees. About 15% of efficiency at inlet angle of 20 degrees is higher than inlet angle of 40 degrees and 31% higher than inlet angle oof 50 degrees. Because there is liner functional relationship between speed and flow rate, suction flow rate at inlet angle of 20 degrees is superior to the inlet angle of 30 degrees as much as 0.89%, inlet angle of 40 degrees as 13%, inlet angle of 50 as 28.4%. Head at inlet angle of 20 degrees is superior to the inlet angle of 30 degrees as much as 0.4%, inlet angle of 40 degrees as 2.7%, inlet angle of 50 degrees as 3.2%. There should exist highest efficiency and also optimal design shape at inlet angle of 20 degrees.

• International Journal of Fluid Machinery and Systems
• /
• v.2 no.1
• /
• pp.80-91
• /
• 2009

In this study, a prediction theory for specific noise that is the overall characteristic of the fan has been proposed. This theory is based on total pressure prediction and broadband noise prediction. The specific noises of two forward curved fans with different number of blades were predicted. The flow around the impeller having 120 blades (MF120) was more biased at a certain positions than the impeller with 40 blades (MF40). An effective domain of the energy conversion of MF40 has extended overall than MF120. The total pressure was affected by the slip factor and pressure loss caused by the vortex flow. The suppression of a major pressure drop by the vortex flow and expansion of the effective domain for energy conversion contributed to an increase in the total pressure of MF40 at the design point. The position of maximum relative velocity was different for each fan. The relative velocity of MF120 was less than that of MF40 due to the deviation angle. The specific noise of MF120 was 2.7 dB less than that of MF40 due to the difference in internal flow. It has been quantitatively estimated that the deceleration in the relative velocity contributed to the improvement in the overall performance.

• The KSFM Journal of Fluid Machinery
• /
• v.13 no.2
• /
• pp.59-64
• /
• 2010

A design method of Sirocco fan is developed for constructing 3-D impeller and scroll geometries, and for predicting both the aerodynamic performance and the noise characteristics of the designed fan. The aerodynamic blading design of fan is conducted by blade angle, camber line determinations and airfoil thickness distribution, and then the scroll geometry of fan is designed by using logarithmic spiral. The aerodynamic performance of designed fan is predicted by the meanline analysis with flow blockage, slip and pressure loss correlations. Based on the predicted performance data, fan noise is predicted by two models for cutoff frequency and broadband noise sources. The present predictions for the performance and the noise level of actual fans are well agreed with measurement results.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.690-695
• /
• 2001

The three-dimensional spatial structures of impeller flow created by a six bladed Rushton turbine have identified based on the volumetric velocity information from multi-plane stereoscopic PIV measurements. A total of 10 planes with 2 mm space with a 50 mm by 64 mm size of the field of view were targeted. To reduce the depth of focus, we adopted an angle offset configuration which satisfied the Scheimpflug condition. The distortion compensation procedure was utilized during the in situ calibration. Phase-locked instantaneous data were ensemble averaged and interpolated in order to obtain mean 3-D, volumetric velocity fields on a 60 degree sector of a cylindrical ring volume enclosing the turbine blade. Using the equi-vorticity surface rendering, the spatial structure of the trailing vortices was clearly demonstrated. Detail flow characteristics of the radial jet reported in previous studies of mixer flows were easily identified.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.6
• /
• pp.773-780
• /
• 2003

The three-dimensional spatial structures of impeller flow created by a six bladed Rushton turbine have identified based on the volumetric velocity information from multi-plane stereoscopic PIV measurements. A total of 10 planes with 2 mm space and a 50 mm by 64 mm size of the field of view were targeted. To reduce the depth of focus, we adopted an angle offset configuration which satisfied the Scheimpflug condition. The distortion compensation procedure was utilized during the in situ calibration. Phase-locked instantaneous data were ensemble averaged and interpolated in order to obtain mean 3-D. volumetric velocity fields on a 60 degree sector of a cylindrical ring volume enclosing the turbine blade. Using the equi-vorticity surface rendering, the spatial structure of the trailing vortices was clearly demonstrated. Detail flow characteristics of the radial jet reported in previous studies of mixer flows were easily identified.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.2
• /
• pp.187-196
• /
• 2016

In this study, a newly developed agitator with hydrofoil impeller applied to actual biological process in advanced wastewater treatment plant was evaluated. Several series of experiments were conducted in two different wastewater treatment plants where actual problems have been occurred such as the production of scums and sludge settling. For more effective evaluation, computational fluid dynamics (CFD) and measurements of MLSS (Mixed Liquor Suspended Solids) and DO (Dissolved Oxygen) were used with other measuring equipments. After the installation of one unit of vertical hydrofoil agitator in plant A, scum and sludge settling problems were solved and more than seventy percent of operational energy was saved. In case of plant B, there were three cells of each anoxic and anaerobic tanks, and each cell had one unit of submersible horizontal agitator. After the integration of three cells to one cell in each tank, and installation of one vertical hydrofoil agitator per tank, all the problems caused by improper mixing were solved and more than eighty percent of operational energy was found to be saved. Simple change of agitator applied to biological process in wastewater treatment plant was proved to be essential to eliminate scum and sludge settling problems and to save input energy.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.649-654
• /
• 2001

This paper describes aerodynamic preliminary design performance prediction and flow analysis for centrifugal compressor of the marine middle engine turbocharger. The performance characteristics of turbocharger compressor are investigated at various operating conditions using mass flow rate and revolution speed, and computational flow analysis for impeller and diffuser at design point are performed. Preliminary design results correspond to actual compressor geometric values comparatively by applying modified slip factor. Performance prediction and flow analysis results show good agreement with experiments. Therefore, this will provide the performance prediction in preliminary design, and help to increase the design capability for optimized impeller.