• Magazine of the Korea Concrete Institute
• /
• v.2 no.4
• /
• pp.69-82
• /
• 1990

This paper proposes equations for balanced-steel ratio to predict the failure types in reinforced concrete beams under pure torsion. Equations are theoretically derived using a space truss model and considering a softening effect which reduces the strength of concrete due to the diagonal crack. To investigate the validity of the proposed equations, experiments were conducted with 13 specimens. Corre¬lation between predicted failure types by balanced - steel ratio and the experimental results in the literature was good. but not for beams tested in this paper.

• Tunnel and Underground Space
• /
• v.17 no.2 s.67
• /
• pp.128-138
• /
• 2007

At low in-situ stress, the continuity and distribution of natural fractures in rock mass predominantly control the failure processes. However at high in-situ stress, the failure process are affected and eventually dominated by stress-induced fractures preferentially growing parallel to the excavation boundary. This fracturing is often observed in brittle type of failure such as slabbing or spatting. Recent studies on the stress- or excavation-induced damage of rock revealed its importance especially in a highly stressed regime. In order to evaluate the brittle failure around a deep underground opening, physical model experiments were carried out. For the experiments a new tue triaxial testing system was made. According to visual observation and acoustic emission detection, brittle failure grades were classified under three categories. The test results indicate that where higher horizontal stress, acting perpendicular $(S_{H2})$ and parallel $(S_{H1})$ to the axis of the tunnel respectively, were applied, the failure grade at a constant vertical stress level (Sy) was lowered. The failure initiation stress was also increased with the increasing $S_{H1}\;and\;S_{H2}$. From the multi-variable regression on failure initiation stress and true triaxial stress conditions, $f(S_v,\;S_{H1},\;S_{H2})$ was proposed.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.501-509
• /
• 2004

The proposed model can predict the compressive behaviors of concrete confined with fiber reinforced polymer (FRP) jacket. To model confining concrete by FRP jackets, the hypoelasticity-based constitutive law of concrete In tri-axial stress states has been presented. The increment of strength of concrete has been determined by the failure surface of concrete in tri-axial states, and its corresponding peak strain is computed by the strain enhancement factor that is proposed in the present study, Therefore, the newly proposed model is a load-dependent confinement model of concrete wrapped by FRP jackets to compare the previous models which are load-independent confinement models. The behavior of FRP jackets has been modeled using the mechanics of orthotropic laminated composite materials in two-dimension. The developed model is implemented into the incremental analysis of compressive tests. The verification study with several different experiments shows that the model is able to adequately capture the behavior of the compression test by including better estimations of the axial responses as well as the lateral response of FRP-confined concrete cylinders.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.78-78
• /
• 2011

수열합성법을 이용하여 Si(111) 기판에 ZnO 박막을 성장하였다. ZnO 박막의 성장을 위한 씨앗층은 plasma-assisted molecular beam epitaxy (PA-MBE)를 이용하였다. 씨앗층의 표면 거칠기(root-mean-square roughness)는 2.5 nm이고, 씨앗층 위에 성장된 ZnO 박막은 다양한 크기의 입자들로 이루어져 있었으며 두께는 약 $1.8{\mu}m$로 매우 일정하였다. 배향성을 알아보기 위하여 texture coefficient (TC)를 계산해 보았다. TC(100)과 TC(200)은 a-축 배향성을, TC(002)는 c-축 배향성을 나타내는데, c-축으로 더 우세한 배향성(99.5%)을 보였다. TC 비율(TCa-axis/TCc-axis)은 열처리 온도를 $700^{\circ}C$까지 올렸을 때, 점차적으로 증가하였고, 그 이상의 열처리 온도(< $900^{\circ}C$)에서는 급격히 감소하였다. 잔류응력과 Zn와 O의 bond length도 유사한 경향을 보였다. $700^{\circ}C$까지 열처리 온도가 증가함에 따라, 잔류응력은 증가하였고 bond length는 감소하였다. Near-band-edge emission (NBE)의 피크 강도는 열처리 온도가 $700^{\circ}C$까지 증가함에 따라 점차적으로 증가하였다. 열처리 온도가 $800^{\circ}C$ 이상 증가함에 따라 deep-level emission (DLE)가 적색편이(red-shift)하였다. $700^{\circ}C$로 열처리를 한 ZnO 박막이 가장 우세한 (002)방향의 배향성을 보였을 뿐만 아니라 가장 큰 발광효율 증가를 보였다.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.4
• /
• pp.367-381
• /
• 2007

A transmission tower was designed using the structural methodology to assume a simple truss behavior. However, there is a big difference between a simple truss behavior and a real one. A suitable explanation of structural stability is that it is a semi-rigid connection and not the assumed hinged connection. This study proposes an alternative structural-analysis modeling strategy for the transmission tower design. The element models that were considered were the truss element model, the beam element model, and the combined beam-truss element model. This study includes linear static analysis, free-vibration analysis, and elastic buckling analysis with respect to the design load. The results of the analysis indicate that the axial forces, axial stresses, and maximum displacements of the three analytical models are very similar. However, the bending moments and stresses of the beam element model and of the combined beam-truss element model are significantly high. The results of the free-vibration and elastic buckling analyses show that the beam-truss model can be conservatively used for the transmission tower design.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.90-96
• /
• 2009

The loading condition of actual construction works is complex. The shear effect of mixed-mode load component are crack propagation mechanism in step larger than the crack initial mechanism. Therefore, in this study received a mixed-mode loading on fatigue crack stress ratio on crack propagation path and speed of progress to learn whether stress affects crack propagation. ${\Delta}$ P a constant state of fatigue tests in Mode I, II give the same stress ratio, frequency 10Hz, sinusoidal waveform was used. A lower stress ratio fatigue crack propagation angle is small. This is less affected by the Mode II. Therefore, a mixed-mode fatigue crack propagation is to progress by the Mode. Stress ratio in a mixed mode crack in the path of progress and found a lot of impact.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.5 no.2
• /
• pp.135-146
• /
• 2003

This paper presents the effect of ground vibration induced by vibrohammer and RCD on adjancent subway tunnel performance using FDM program. Firstly, the stability criteria for structures near vibration source were proposed according to existing data, then peak particle velocity around tunnel was estimated based on detailed information of vibrohammer and existing formula for dynamic loads through numerical analysis. The peak particle velocity induced by RCD bit rotation was also estimated using surveyed data and formula. Consequently, displacement and stress responses were obtained at crown, shoulder and spring line and compared with the criteria to check stability of tunnel.

• Journal of the Korea Concrete Institute
• /
• v.17 no.4 s.88
• /
• pp.513-520
• /
• 2005

The uniform truss mechanism is widely accepted as a shear transfer mechanism in reinforced concrete members. However, the uniform truss action cannot be expected when the bond stress distribution is not constant along longitudinal bars. A test method in which only the truss action takes place is developed and conducted to investigate the truss actions under various bond contributions. Based on the experimental results and analysis, the following findings can be obtained: 1) The bond stress distribution depends on the axial compression force, the amount of shear reinforcement and loading conditions. 2) The analysis using the combined truss model consisting of uniform and fan-shape trusses can predict the experimental results

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.97-104
• /
• 2005

A simple but efficient grid generation technique by using the modified compressible form of stream function has been formulated. Transformation of a physical plane to a streamline plane, the Von Mises Transformation, has been widely used to solve the differential equations governing flow phenomena, however, limitation arises in low velocity region of boundary layer, mixing layer and wake region where the relatively large grid spacing is inevitable. Modified Von Mises Transformation with simple mathematical adjustment for the stream function is suggested and applied to solve the confined coaxial turbulent jet mixing with simple $\kappa-\epsilon$ turbulence model. Comparison with several experimental data of axial mean velocity, turbulent kinetic energy, and Reynolds shear stress distribution shows quite good agreement in the mixing layer except in the centerline where the turbulent kinetic energy distributions were somewhat under estimated. This formulation is strongly suggested to be utilized specially for free turbulent mixing layers in axisymmetric flow conditions such as the investigation of mixing behavior, jet noise production and reduction for Turbofan engines.

• Journal of Korean Society of Steel Construction
• /
• v.19 no.1
• /
• pp.117-127
• /
• 2007

In this study, we evaluate the strength of steel box beam-to-column connections subjected to axial loads in steel frame piers. The T-connection strength was reduced due to the column axial force in the two-story pier structure. To examine this phenomenon, non-linear FEM analysis was carried out and the analytical procedure was verified by comparing it with experimental results. To clarify the effect of the axial force and major design parameters in connection with strength, influence of panel zone width-thickness ratio, sectional area, and axial force was investigated using FEM analysis. Also, the theoretical strength equations were suggested by stress distribution of panel zone. The strength of the T-connection was compared with one of the one-story pier structure connections. As a result, the strength evaluation equations are proposed in consideration of the panel zone width-thickness ratio and sectional area ratio for the T-connections.