• Journal of the Korea Concrete Institute
• /
• v.14 no.2
• /
• pp.231-238
• /
• 2002

Dry shrinkage md temperature change cause to develope concrete bridge decks on main girders have initial unidirectional cracks in longitudinal or transverse direction. As they receive traffic loads, the crack gradually propagate in different directions depending on the concrete dimension and reinforcement ratio. Since existing equations that predict crack width are mostly based on the one directional bond-slip theory, it is difficult to determine the actual crack width of a bridge deck with varying the spacing of rebar or strengthening material and to estimate the improvement rate in serviceability of the strengthened bridge deck. In this study, crack propagation mechanism is identified based on the test results and a new crack prediction equation is proposed for evaluation of serviceability. Although more accurate results are derived using the proposed equation, the extent of error is increased as the strain of the rebar or the strengthening material increases after the yielding of rebar Therefore, further research is required to better predict the crack width after the rebar yields under fatigue loading condition.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.06a
• /
• pp.1-6
• /
• 2000

가압 경수로의 증기발생기는 원자로(reactor vessel)와 가압기(pressurizer)에서 가열ㆍ가압된 1차 계통의 고온, 고압수가 터빈을 돌리는 2차 계통수와 열교환을 일으켜 고온ㆍ고압의 증기를 발생시키는 것으로, 전열관의 파손이 발생될 경우 1차 계통에서 2차 계통으로 방사능 물질이 누출되어 심각한 문제가 야기된다. 따라서 증기발생기의 전열관 손상이나 파손 문제는 원자력 발전소의 수명과 밀접한 관계가 있다. (중략)

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.352-357
• /
• 2020

This study was performed to solve the quality problems of forging propeller shaft components in the marine diesel engines during the final cooling process and provide reasonable guidelines to increase the production of forging products. Residual hydrogen existing on the inside of forging products begins to diffuse and accumulates at the pores, micro-fissures, and grain boundaries as the temperature of forging products begins to decrease and reaches a critical temperature range, and finally transforming into internal defects. These defects were easily found near the surface of products after milling the surface of forging products. In this work, four types of forging products (shaft flange, shaft journal, thrust shaft, and propeller shaft) were chosen to evaluate the temperature history of products during the cooling process, employing non-linear numerical analyses with the ANSYS program. The times elapsed to reach 250 ℃ after cooling were approximately 9 ~ 23 hours for each forging product. These times can be used as cooling process guidelines on the quality and productivity of products after heat treatment.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.3
• /
• pp.309-316
• /
• 2015

A state-based peridynamic model is able to describe a general constitutive model from the standard continuum theory. The response of a material at a point is dependent on the deformation of all bonds connected to the point within the nonlocal horizon region. Therefore, the state-based peridynamic model permits both the volume and shear changes of the material which is promising to reproduce the complicated dynamic brittle fracture phenomena, such as crack branching, secondary cracks, cascade cracks, crack coalescence, etc. In this paper, the two-dimensional state-based peridynamic model for a linear elastic plane stress solid is employed. The damage model incorporates the energy release rate and the peridynamic energy potential. For brittle glass materials, the impact of the crack-parallel compressive stress waves on the crack branching pattern is investigated. The peridynamic solution for this problem captures the main features, observed experimentally, of dynamic crack propagation and branching. Cascade cracks under strong tensile loading and secondary cracks are also well reproduced with the state-based peridynamic simulations.

• International Journal of Highway Engineering
• /
• v.4 no.2 s.12
• /
• pp.33-42
• /
• 2002

The cracks in the pavements result from drying shrinkage, temperature change, repeated traffic loadings and so on. The reduction of soil support, spatting and many local failures are caused by water and incompressible foreign materials infiltrated into the cracks. In order to reduce this kind of problems the crack width must be controlled and managed by the accurate measurement. The current method is a visual survey using a microscope, which requires traffic blocking. The purpose of this study is to find the best condition to measure accurate crack width using automated pavement condition survey equipment running at the similar speed as other vehicles. In this study pavement surfaces are filmed on an enlarged scale by the camera with a zoom lens, and then the proper focal distance is determined according to the crack width through a pilot survey. The conditions for measurement of the accurate crack width using the image processing technique are suggested by comparing crack widths surveyed using a microscope in the field with those computed by various factors in the image processing program, STADI-2. In conclusion, the camera with a focal distance of 75m could detect crack range of 0.5mm$\sim$1.2mm In width with an accuracy of 80% for CRCP. The camera with a focal distance of 12.5mm could detect crack range of 1.8mm$\sim$3.3mm in width with an accuracy of 90% for asphalt pavement.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.4
• /
• pp.529-537
• /
• 2021

Membrane-type hull and cargo holds have been designed and built for large ship. However, there is a growing interest in applying the same technology to small and medium-sized Liquefied natural gas(LNG) carriers to meet the recent increase in demand for LNG as an ecofriendly fuel and for expanding LNG bunkering infrastructure. The purpose of this study is to apply the IMO Type-B tank to small and medium-sized LNG carriers and verify the safety and suitability of the design. Fatigue crack propagation analysis was performed to install a partial second drip tray installed at the lower part of the LNG cargo tank by calculating the amount of leaked gas in the support structure supporting the cargo tank. First, a program for fatigue crack propagation analysis was developed, in which Paris' law and British Standard 7910 (BS 79110) were applied based on the International Code for the Construction of Equipment and Ships Carrying Liquefied Gases in Bulk, an international standard for LNG carriers. In addition, a surface crack propagation analysis was performed. Next, a methodology for assuming the initial through-crack size was developed to determine the size of the partial second barrier. The analysis was performed for 15 days, which is a possible return time after cracks are detected. Finally, the safety and suitability of the IMO Type-B for LNG cargo tanks required by international regulations were verified. For the accurate analysis of fatigue crack propagation, it is necessary to develop and verify the analysis procedure based on direct analysis and international regulations.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.229-238
• /
• 2009

This paper describes the methods to propose the optimal material properties and construction steps that prevent cracks due to the thermal stresses induced by the hydration heat under the construction of the concrete underpass structures. To achieve the goal of this study, the heat transfer theories were employed and the three-dimensional finite element model of the underpass structure was developed and used for the structural analyses. If the volume of the concrete member that is placed at one time is significantly large, the member is assumed to be the mass concrete and is easy to induce cracks. In order to minimize the cracks during the construction, two different methods can be utilized: one is to arrange the construction steps optimally and the other is to change the materials to reduce the probability of the crack occurrence. In this study, the analyses were performed by considering the changes in material properties with time, the characteristics of the hydration heat generation for cements and admixtures, the volume of the concrete placement at one time, and the environmental conditions.

• Journal of Energy Engineering
• /
• v.21 no.4
• /
• pp.362-372
• /
• 2012

The steam generator tubes of nuclear power plants are pressure boundaries, and if tubes are leaked, the coolant with the radioactive materials was flowed out from the primary system to the secondary system and polluted the plant and the air. Recently most crack defects of tubes are stress corrosion cracks and these defects are located in expansion transition area, sludge pile-up region, and U-bend area. The most effective one of crack initiation factors in expansion transition area and U-bend area is the residual stress. According to the experiences of Korea standard nuclear plants(Optimized Power Reactor-1000), they had the stress corrosion cracks at the tube expansion transition area in early operating stage and especially lots of circumferential cracks were occurred. Therefore in this study, the distributions and conditions of residual stresses by tube expansion methods were compared and the dominant reason of a specific direction was examined.

• Journal of the Society of Disaster Information
• /
• v.16 no.3
• /
• pp.449-457
• /
• 2020

Purpose: The Seoul Metropolitan Government classifies the cavity risks into emergency, priority, general, and observation grades in consideration of the cavity size, asphalt pavement thickness, and pavement depth based on the cavity management grade criteria of Seoul. In this study, the depth of cracking was measured at 17 cracks identified by checking the pavement condition of the cavity at 265 cavities found in the 2019 cavity investigation service. Method: In the first phase, crack width and depth were measured using a vernier caliper, taper gauge, and depth gauge to check the cracks of the identified cavities. In the second phase, the location of the largest crack in the upper road surface was confirmed, and A.C. was drilled to further measure the crack depth. Results: As a result, the cavity management level was raised in nine of the 17 test cavity identified. Therefore, in case of emergency and priority recovery, the grade should be adjusted according to the depth of pavement crack and the thickness of residual A.C. pavement. Conclusion: In the case of cracks in the upper part of the cavity, the crack progression must be determined through the perforation and the remaining asphalt concrete thickness must be determined to determine the cavity grade.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.28 no.4
• /
• pp.352-357
• /
• 2008

The detection of micro cracks in materials at the early stage of fracture is important in many structural safety assurance problems. The nonlinear ultrasonic technique (NUT) has been considered as a positive method for this, since it is more sensitive to micro crack than conventional linear ultrasonic methods. The basic principle is that the waveform is distorted by nonlinear stress-displacement relationship on the crack interface when the ultrasonic wave transmits through, and resultantly higher order harmonics are generated. This phenomenon is called the contact acoustic nonlinearity (CAN). The purpose of this paper is to prove the applicability of CAN experimentally by detection of micro fatigue crack artificailly initiated in Aluminum specimen. For this, we prepared fatigue specimens of Al6061 material with V-notch to initiate the crack, and the amplitude of second order harmonic was measured by scanning along the crack direction. From the results, we could see that the harmonic amplitude had good correlation with COD and it can be used to detect the crack depth in more accurately than the common 6 dB drop echo method.