• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.110.1-110.1
• /
• 2005

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.464-468
• /
• 2003

A general program of three dimensional profile design of impellers for centrifugal/fixed-flow compressors is successfully commercialized using Bezier curves and quasi-3D flow analysis methods. Control points for meridional hub and shroud contours and blade camberline angles are arbitrarily changed to give smooth Bezier curves. With specified blade normal thicknesses, contructed geometry is instantly analyzed using flow analysis methods to be checked.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.405-410
• /
• 2004

2-dimensional impeller's distinctive feature is expected to have an influence on performance and flow characteristics of centrifugal compressor. And new design method is required for 2-dimensional impeller, because the unique geometry cannot be designed using conventional theories. The objective of this study is to advance new design technology for 2-dimensional impeller and to investigate the performance characteristics of designed 2-dimensional centrifugal compressor. The performance test for 2-dimensional impeller is conducted at 35000, 40000 and 45000rpm. Also numerical calculation is applied by using commercial CFD code, FLUENT, and the results are compared with experimental results.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.4
• /
• pp.5-11
• /
• 2011

This study investigated on details of flow characteristics in a vaneless diffuser of a compressor with 2-dimensional impeller at various flow rates. Experiment for a low speed compressor model in a water reservoir was performed to analyze the flow field in the vaneless diffuser and volute casing, which was done by PIV measurement. It was also focused on the periodic flow patterns occurring at low flow rate near unstable operating region of the compressor. At low flow rate condition, the flow visualization clearly shows that the flow energy from impeller is highly accumulated at the compressor exit by the blockage effect of a flow damper and consequently the reverse flow occurs in the diffuser.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.1 s.6
• /
• pp.43-50
• /
• 2000

Upgrade development of a high pressure ratio centrifugal compressor in marine engine turbochargers is presented. A new matched operating point at increased speed of rotation was determined through system cycle analysis using the exisitng test data of turbine performance. Under some severe restrictions for geometric parameters, the state-of-the-art methods of both aerodynamic design and CFD analysis were applied, in which only an impeller, a vaned diffusor and some part of casing wall were modified. Prototype hardware was fabricated and assembled for system performance tests. Excellent performance in pressure ratio and efficiency was obtained over whole speed region. Reduced surge and choke margin was, however, observed at design speed of rotation.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.517-524
• /
• 2005

An aerodynamic design for centrifugal compressor which was applied to medium speed diesel engine has done. First of all, exact compressor specifications must be defined by accurate engine system matching. This matching program has been developed. Using the mean1ine prediction method, geometric design and performance curve for compressor was done and verified by comparing three dimensional viscous CFD results. The deviation at the design point was about 2.3%. Combustor has been designed and manufactured for the performance test of medium speed diesel engine turbocharger. Fuel nozzle of combustor was designed and performed by PIV and PDPA test equipment. Through these results, spray characteristics were studied and flow coefficient equation was deduced.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.1 s.2
• /
• pp.64-72
• /
• 1999

CSCM upwind flux difference splitting compressible Navier-Stokes method has been used to predict the transonic flows in a centrifugal compressor diffuser. The modified cyclic. TDMA and the mass flux boundary conditions were used as boundary conditions of the diffuser analysis. Broad flow separation on the suction surface near the hub and shroud was observed from the results of the mass flow rates 5.8, 6.0 and 6.2kg/s at 27000 rpm. The three-dimensional flow analysis predicted successfully that the static pressure increased and the total pressure decreased through the flow passage of the channel diffuser when compared to two-dimensional analysis due to the strong effect of the three-dimensional flow. The mass averaged loss coefficients and pressure coefficients were also studied.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.5
• /
• pp.22-29
• /
• 2008

This study is performed to understand the effect of the variation in the passage area of a two-dimensional impeller on its performance characteristics. We observe the results with changing the area ratio of inlet to outlet about $1{\sim}2.8$. A comparison between the experimental and numerical results was performed for the same configuration in order to verify the reliability of the CFD code. Overall characteristics in the passages of impeller were analyzed in detail including streamline, Mach number, pressure and polytropic efficiency distribution. When the passage area ratio exceeds 2, the pressure ratio is high. An area ratio of 2.3 showed the highest efficiency. The results will be used as useful reference data to establish the design concept of two-dimensional impeller and to improve its performance.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.2 s.35
• /
• pp.30-38
• /
• 2006

An aerodynamic design for centrifugal compressor which was applied to medium speed diesel engine has been done. First of all, exact compressor specifications must be defined by accurate engine system matching. This matching program has been developed. Using the meanline prediction method, geometric design and performance curves for compressor were established and verified by comparing three dimensional viscous CFD results. The deviation at the design point was about 2.3%. Combustor has been designed and manufactured for the performance test of medium speed diesel engine turbocharger. Fuel nozzle of combustor was designed and its characteristics was analyzed by PIV and PDPA test equipment. Through these results, spray characteristics were studied and flow coefficient equation was deduced.

• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.217-222
• /
• 1998

CSCM upwind flux difference splitting compressible Navier-Stokes method has been used to predict the transonic flows in centrifugal compressor diffuser. The modified cyclic TDMA and the mass flux boundary conditions were used as boundary conditions of the diffuser analysis. With the mass flux boundary condition and the $130{\times}80{\times}40$ grid, the compressible upwind Navier-Stokes method predicted the transonic diffuser flowfield successfully. Plow changes in the impeller exit region due to the strong interaction between impeller exit and vaned diffuser, broad flow separation on the suction surface near hub and shroud was observed from the results of the mass flow rates 6.0 and 6.2kg/s at 27000 rpm. The static pressure increased and the total pressure decreased through the flow passage of the channel diffuser, which were predicted better from the three-dimensional analysis than from the two-dimensional analysis due to the strong effect of the three-dimensional flow. The mass averaged loss coefficients and pressure coefficients were also studied.