• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.5
• /
• pp.445-451
• /
• 2000

To estimate dry deposition flux of 12 elements in aerosols, aerosol particles were sampled by a low-pressure impactor(LPI) and a dust jar. The concentrations of 12 elements in aerosol particle and dry deposition were analyzed by a PIXE analysis using as a 2.0 MeV-proton beam. The mean dry deposition velocities of 12 elements were estimated by ranges of 0.74∼2.62 cm/sec. The results showed that the highest value was 3.26 cm/sec for Ca and the lowest value 0.74 cm/sec for Fe. The dry deposition flux for elements was calculated as a function of particle size by 1-step method and 12-step method. In this work, dry deposition velocities were computed with the two existing models; the coarse-particle fraction(4∼30 mm diameter) using the dry deposition velocity model of the Noll and Fang(1998) and the fine-particle fraction (0.05∼4mm diameter) using the Shemel and Hodgson(1980) model. The ratios of the mean calculated/measured fluxes were 3.59 for 1-step method and 0.60 for 12-step method respectively.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.9-13
• /
• 2019

This paper presents an optimal design of a brushless DC motor considering an advanced $165^{\circ}$ 12 step control for a cost reduction. The advanced 12 step control that extends the conduction angle $150^{\circ}$ can improve the output of the motor. The optimal design considering the improved output power of the motor is proposed by reducing the volume of rotor, stator and permanent magnet using response surface method. The proposed design satisfied the performance requirements and efficiency improvement of the conventional motor and reduced the volume about 3.5%. The feasibility of the optimal design is proved by the electromagnetic field analysis using the finite element method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.12
• /
• pp.2047-2054
• /
• 2003

In this paper, an approach of automatically finding and modifying the most appropriate orthogonal array (GO) is suggested and applied to a new structural optimization procedure with two steps. GO is motivated by the situation where finding a proper orthogonal array from the tables in the literature is difficult or impossible. Now the Taguchi method is made available for various numbers of variables and levels. In the two-step structural optimization, the Taguchi method equipped with GO and a shape optimization using the finite differencing method is consecutively applied. The existence or non-existence of an element can be taken as a factor level and this feature is utilized finding the best topology from a set of potential topologies suggested from the user's expertise. This greatly enhances applicability and one can expect a better result than the case in which each step is applied independently because these steps are complementary each other.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2055-2067
• /
• 1997

Values of process parameters in sheet metal forming can be estimated by various one-step inverse methods. One-step inverse methods based on deformation theory, however, cause some amount of error. The amount of error is generally increased as the deformation path becomes more complex. As a remedy, a new three dimensional multi-step inverse method is introduced for optimum design of blank shapes and strain distributions from desired final shapes. The approach extends a one-step inverse method to a multi-step inverse method in order to reduce the amount of error. The algorithm developed is applied to square cup drawing to confirm its validity by demonstrating reasonably accurate numerical results. Rapid calculation with this algorithm enables easy determination of an initial blank of sheet metal forming.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.12
• /
• pp.1189-1196
• /
• 2010

This paper provides an identification method for three-parameter models i.e. first order with dead time models and second order with dead time models. The proposed identification method is based on step response and can be easily implemented using digital microprocessors. The proposed method first identifies the order of the plant i.e. first order or second order from the behavior of the plant with constant input. After the order of the plant is determined, a test step input is applied to the system and the three parameters of the plant are obtained from the corresponding response of the plant. The output of the plant need not to be zero when the test signal is applied. The efficacy of proposed algorithms is verified through simulation and experiment.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.5
• /
• pp.450-456
• /
• 2005

In this paper new 60-step inverter system for medium-to-large scale STATCOM is proposed and operating principle along with control method is detailed. A simple auxiliary circuit is employed to Improve output voltage waveform of 12-step into 60-step. The proposed scheme could be a cost effective approach in high power application such as 10Mvar to 30Mvar STATCOM. Experimental results from a 2KVA laboratory prototype show validity of the proposed method.

• Textile Coloration and Finishing
• /
• v.11 no.5
• /
• pp.7-12
• /
• 1999

The objective of this study is to apply water repellent and flame retardant finishes simultaneously to the fabric used for automobile. Both two step and one step methods were tried to apply the finishing agent to the fabric. In the two step method, water repellent agent was treated first, and flame retardant agent was applied next. The reverse finishing process was also attempted. In the one step method, flame retardant agent and water repellent agent treated to the fabric in one bath. The results of two step method revealed that the finishing effect was better when the water repellent agent was treated first than when flame retardant agent was treated first. In one step method, fluoro water repellent agent was superior to silicon water repellent agent.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.209-215
• /
• 2006

Now, in this paper, going to present you with an Idea related to a new inverter of multi-step voltage source, that Is, the double-connected 12-step inverter with an auxiliary circuit. It possibly can be 24-step inverter with 3-phase voltage source which will enable us make full application even to medium and high power-level Motor drive, UPS, STATCOM, SVC, etc. in which the PWM method could not be employed. 24-step operation can be obtained from the link between the existing 12-step inverter and the additional auxiliary circuit in which the transformer of auxiliary circuit generates ripple voltage delivered to the inverter. Through a lot of experiments and simulations, (from which the validity of this scheme is confirmed,) we came to the conclusion that the increase of the primary winding number on transformer by 2N(N=1,2,3....) leads to the 12M-step(M=2,3,4...) inverter. The validity of the proposed scheme is confirmed by the simulated and experimental results.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.12
• /
• pp.567-572
• /
• 1986

In this paper, a new type of step motor with two degree of mechanical freedom, which is named rotary-Linear Step Motor(RLSM), is presented. Its rotor axis can perform linear and rotary motions either separately or simultaneously. This paper discribes the design of RLSM using finite element method in which the magnetic saturation effect of the iron core is taken into account. The design parameters such as torques, forces and inductances are obtained from the computed magnetic vector potentials. A new type of Rotary-Linear Step Motor was constructed. The calculated parameters agree well with measurements.

• Transactions of Materials Processing
• /
• v.12 no.5
• /
• pp.449-456
• /
• 2003

Multi-step induction heating process was applied to the powder compact melting technique as a new heating process to achieve pinpoint accuracy, faster cycle time, repeatability, non-contact and energy-efficient heat in a minimal amount of time. The objective of this study is the establishment of the input data diagram of multi step induction heating process for automation of the fabrication process of 6061 Al foams with desired density. At first, proper induction coil was designed to obtain a uniform temperature distribution over the entire cross sectional area of specimen. By using this coil, foaming experiments were performed to investigate the multi-step induction heating conditions such as capacity, temperature and time conditions of each heating and holding step. On the basis of the obtained multi-step induction heating conditions, relationship between final heating temperature and fraction of porosity was investigated.