• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.2
• /
• pp.447-455
• /
• 2014

This study was intended to estimate the efficiency of inducing fiber arrangement in UHPCC (Ultra High Performance Cementitious Composites). For the purpose, UHPCC members produced by several different placing methods according to flow characteristics were prepared; flexural behaviors were compared and correlation between the flexural behavior and the characteristics of fiber arrangement was investigated. Test results showed that placing method for inducing specific fiber arrangement had a considerable influence on the flexural performance. The standard specimen in which fibers are induced to be directed parallel to the principle tensile direction presented higher flexural tensile strength but lower variation. Therefore it should be considered that the flexural tensile strength actually developed in UHPCC member may be highly different and in lager variation. The qualitative variation of fiber arrangement according to the flow of UHPCC was also predicted considering the flow pattern and the boundary effect; the prediction provided good explanation to the difference in the flexural behavior according to the induced flow.

• Journal of the Korea Concrete Institute
• /
• v.26 no.6
• /
• pp.771-778
• /
• 2014

This paper concerns the flexural behavior of hybrid steel fiber-reinforced ultra high performance concrete (UHPC) beams. It presents experimental research results of hybrid steel fiber-reinforced UHPC with steel fiber content of 1.5% by volume and steel reinforcement ratio of less than 0.02. This study aims at providing realistic information about UHPC beams in bending in order to establish a reasonable prediction model for flexural resistance in structural code in the future. The experimental results show that hybrid steel fiber-reinforced UHPC is in favor of cracking resistance and ductility of beams. The ductility indices range through 9.2 to 15.2, which means high ductility of UHPC. Also, the flexural capacity of beam which contains stirrups in pure bending zone is similar to that of beam which does not contain stirrups in pure bending zone. This result represents that the flexural capacity is not affected by the presence of stirrups whose spacing is 150 mm in bending zone.

• Journal of the Korea Concrete Institute
• /
• v.19 no.5
• /
• pp.529-537
• /
• 2007

The purpose of this study is to discuss how strength and ductility of each system in low-rise reinforced concrete buildings composed of extremely brittle, shear and flexural failure lateral-load resisting systems have influence on seismic capacities of the overall system, which is based on nonlinear seismic response analyses of single-degree-of-freedom structural systems. In order to simulate the triple lateral-load resisting system, structures are idealized as a parallel combination of two modified origin-oriented hysteretic models and a degrading trilinear hysteretic model that fail primarily in extremely brittle, shear and flexure, respectively. Stiffness properties of three models are varied in terms of story shear coefficients, and structures are subjected to various ground motion components. By analyzing these systems, interaction curves of demand strengths of the triple system for various levels of ductility factors are finally derived for practical purposes. The result indicates that demand strength levels derived can be used as a basic information for seismic evaluation and design criteria of low-rise reinforced concrete buildings having the triple lateral-load resisting system.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.631-633
• /
• 2012

본 논문은 구조용 후판 강재로 절곡되었을 때, 절곡부재의 구조연성 변화에 대한 해석 방안과 이에 따른 해석적 평가 사례를 제시하고 있다. 절곡 방법에 의한 제작과정에서 재료는 변형경화 현상이 발생한다. 이로 인해 구조연성 저하가 불가피하기 때문에 절곡부재의 휨연성 검토가 필요하다. 해석 방안은 유한요소해석 프로그램인 ABAQUS를 이용하였다. Lanczos 알고리즘을 적용한 고유치해석과 재료 비탄성-기하비선형을 고려한 비선형 해석을 하였다. 비선형해석 절곡에 의한 재료특성을 고려하였다. 극한 하중과 파괴모드를 평가하기 위해 Newton-Raphson method, modified Riks method를 적용한 단계별 하중재하 해석을 실시하였다. 본 연구를 통해 휨연성을 평가하는데 활용 될 것으로 판단된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.9 no.4
• /
• pp.9-14
• /
• 1989

A strain rate-dependent element model was used to study the loading rate-sensitivity of R/C beams and columns with different design factors. Conclusions were derived regarding the differences between the element axial/flexural performance under impulsive and quasi-static loads. Practical design formalas for predicting the loading rate-dependent axial and flexural strengths of R/C elements were also suggested.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2009.04a
• /
• pp.251-254
• /
• 2009

건설 분야에서 FRP(Fiber Reinforced Polymers) 부재는 기존의 건설부재에 비해 많은 장점을 가지고 있어 여러 분야에서 연구 및 개발이 이루어지고 있다. 그중 FRP 재료를 이용한 교량 부재들이 해외 뿐만 아니라 국내에서도 연구되고 있으며, FRP 인장재 및 바닥판은 연구 및 개발이 완료돼 현재 시공 중에 있고 FRP 휨 부재 또한 연구가 활발히 진행되고 있다. 이런 FRP 부재는 외부 환경에 그대로 노출됨으로써, 온도 등의 주위 환경의 변화에 많은 영향을 받게 되며, 특히 높은 온도에 취약한 성질을 가지고 있다. 이에 본 연구에서는 FRP 부재의 온도에 따른 역학적 특성을 파악하기위한 실험적 연구로써, $-21^{\circ}C$, $100^{\circ}C$, $200^{\circ}C$에 각각 1시간씩 시험체를 보관한 뒤 내구성 실험을 실시하였다. 각각의 시험체는 FRP 모듈형 박스부재에서 4개씩 채취하였으며, 실험 실시 후 SEM촬영을 실시하여 파괴모드를 분석하였다. 실험 결과 저온일 때는 강도변화가 많이 나타나지 않았으나 고온일 때 압축 및 휨강도의 급격한 저조를 확인할 수 있었다. 고온 보관 시험체의 SEM(Scanning Electron Microscope) 촬영결과 수지의 손상으로 낮은 강도가 측정되는 것을 확인할 수 있었다.

• Journal of the Korea Concrete Institute
• /
• v.14 no.6
• /
• pp.934-941
• /
• 2002

It is important to consider the effect of member size when estimating the ultimate strength of a concrete flexural member because the strength always decreases with an increase of member size. In this study, the size effect of a reinforced concrete (RC) beam was experimentally investigated. For this purpose, a series of beam specimens subjected to four-point loading were tested. More specifically, three different effective depth (d$\approx$15, 30, and 60 cm) reinforced concrete beams were tested to investigate the size effect. The shear-span to depth ratio (a/d=3) and thickness (20 cm) of the specimens were kept constant where the size effect in out-of-plane direction is not considered. The test results are curve fitted using least square method (LSM) to obtain parameters for the modified size effect law (MSEL). The analysis results show that the flexural compressive strength and the ultimate strain decrease as the specimen size increases. In the future study, since $\beta_1$ value suggested by design code and ultimate strain change with specimen size variation, a more detailed analysis should be performed. Finally, parameters for MSEL are also suggested.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.4
• /
• pp.48-56
• /
• 2013

Prestressed concrete (PSC) members are readly available in civil engineering applications due to the convenience of construction and easy of quality control in the manufacturing process of the member. Especially, half-depth precast concrete composite slab, which is one of the PSC flexural members is developed recently using the long-line method. The half-depth precast concrete composite slabs are composed of the precast concrete and the in-situ concrete placed at the site. In this paper, we present the results of experimental investigations pertaining to the pretensioning efficiency and the flexural behavior of half-depth precast concrete composite slab which is made of precast PSC manufactured by the long-line method. In the long-line method, the pretensioned precast member is manufactured simultaneously, by tensioning tendons at once. In addition, we suggest the equation that can estimate the flexural strength of half-depth precast concrete composite slab reasonably by considering the effects of rebar embedded in the precast PSC flexural member.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4A
• /
• pp.383-389
• /
• 2010

The concrete structural design provisions in Korea are based on ultimate strength design. Up to service load stage, it is assumed a linear stress-strain relation, but there is no stress-strain relationship for a concrete material from service load stage to limat state. According to the current provisions, an independent method is provided for the each calculation of deflection and crack width. In EC2 provisions based on limit state design, however, a stress-strain relationship of concrete is provided. Thereby, it is able to calculate a strength as well as a deflection directly from concrete stress-strain relationship. In this paper the moment-curvature relationship is directly calculated from a material law using equilibrium and compatibility conditions. Then strength and deflection are formulated. These results are compared with the values from the current provisions in Korea. From the results, the deflection based on a moment-curvature relationship is well agreed with experimental results and it is appeared that the deflection after the yielding of steel is also possible.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.5
• /
• pp.353-359
• /
• 2017

The purpose of this study is to evaluate the strength and behavior of the composite member in case of concrete filled steel tube embedded in concrete for application concrete filled steel tube to steel rib support in tunnel. A total of six beam specimens were prepared for steel tube in-filled with plain concrete and aerated concrete, and static bending tests were performed. As a result, the member of concrete steel tube embedded with plain concrete showed higher strength than those with aerated concrete. However, it was found that the flexural strength of member with reinforcing bar around the steel tube is more influenced by the amount of the reinforcing bar than the type of the filled concrete.