• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2004.04a
• /
• pp.179-186
• /
• 2004

Introduction of wave model, considered the effect of shoaling, refraction, diffraction, partial reflection, bottom friction, breaking at the coastal waters of complex bathymetry, is a very important factor for most coastal engineering design and disaster prevention problems. As waves move from deeper waters to shallow coastal waters, the fundamental wave parameters will change and the wave energy is redistributed along wave crests due to the depth variation, the presence of islands, coastal protection structures, irregularities of the enclosing shore boundaries, and other geological features. Moreover, waves undergo severe change inside the surf zone where wave breaking occurs and in the regions where reflected waves from coastline and structural boundaries interact with the incident waves. Therefore, the application of mild-slope equation model in this field would help for understanding of wave transformation mechanism where many other models could not deal with up to now. The purpose of this study is to form a extended mild-slope equation wave model and make comparison and analysis on variation of harbor responses in the vicinities of Pohang Old Harbor and Pohang New Port, etc. due to construction of New Port in Youngil Bay. This type of trial might be a milestone for port development in macroscale, where the induced impact analysis in the existing port due to the developemnt could be easily neglected.

• Korean Journal of Food Science and Technology
• /
• v.52 no.1
• /
• pp.31-39
• /
• 2020

The effects of heat-moisture treatment (HMT) on the functional properties of high amylose rice starches (HARSes) purified from Korean rice varieties (A-type Goami and Singil and B-type Dodamssal and Goami2) were investigated. HMT was accomplished with moisture contents of 18 and 27% and heated at 100℃ for 16 h. While the amylose content, swelling power and solubility decreased after HMT, the water binding capacity and resistant starch (RS) content increased with increasing moisture content after HMT. The X-ray diffraction patterns of all HARSes did not change after HMT, but a decrease in the intensity of peak at 2θ=5° was observed in B-type HMT HARSes. While the starch granules aggregated after HMT, their shape and size remained unchanged. B-type HARSes exhibited higher gelatinization temperatures and lower pasting viscosities than A-type HARSes following HMT. The results, thus, suggest that while the crystalline intensity of B-type Dodamssal and Goami2 rice starches did not change after HMT, the RS content, water binding capacity, and pasting temperatures of all HARSes increased with increasing moisture content after HMT.

• Journal of Navigation and Port Research
• /
• v.28 no.5
• /
• pp.421-428
• /
• 2004

Introduction of wave model, considered the effect of shoaling, refraction, diffraction, partial reflection, bottom friction, breaking at the coastal waters of complex bathymetry, is a very important factor for most coastal engineering design and disaster prevention problems. As waves move from deeper waters to shallow coastal waters, the fundamental wave parameters will change and the wave energy is redistributed along wave crests due to the depth variation, the presence of islands, coastal protection structures, irregularities of the enclosing shore boundaries, and other geological features. Moreover, waves undergo severe change inside the surf zone where wave breaking occurs and in the regions where reflected waves from coastline and structural boundaries interact with the incident waves. Therefore, the application of mild-slope equation model in this field would help for understanding of wave transformation mechanism where many other models could not deal with up to now. The purpose of this study is to form a extended mild-slope equation wave model and make comparison and analysis on variation of harbor responses in the vicinities of Pohang Old Harbor and Pohang New Port, etc. due to construction of New Port in Youngil Bay. This type of trial might be a milestone for port development in macroscale, where the induced impact analysis in the existing port due to the development could be easily neglected.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.701-706
• /
• 1999

The crystal structure and magnetic properties of magnetic oxide system (F $e_2$ $O_3$)$_{5}$(A $l_2$ $O_3$)$_{4-x}$(G $a_2$ $O_3$)$_{x}$)SiO has been studied using X-ray diffraction and Mossbauer spectroscopy The changes of magnetic structure by the Ga ion substitution and the temperature variation have been investigated using Mossbauer spectroscopy, and the results are compared with those of the SQUIB measurements. Results of X-ray diffraction indicated that the crystal structures of the system change from a cubic spinel type to an orthorhombic via the intermediate region. This magnetic oxide system seems to be new kind of spinel type ferrites containing high concentration of cation vacancies. Various and complicated Mossbauer spectra were observed in the samples (x>0.2) at temperatures lower than room temperature. This result could be explained by freezing of the superparamagnetic dusters. On cooling and substitution, magnetic states of the system show various and multicritical properties. Unexpected dip in magnetization curves below 50K was observed in SQUID measurements. It was interpreted as an effect of spin canting including spin freezing or collective spin behavior.ior.r.

• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.60-70
• /
• 1995

Polycrystalline $Cd_{1-x}Zn_{x}S$ thin film were grown on slide glass(corning-2948) substrate using a chemical bath deposition (C.B.D) method. They were annealed at various temperature and X -ray diffraction patterns were measured by X-ray diffractometor in order to study $Cd_{1-x}Zn_{x}S$ polycrystal structure using extrapolation method of X-ray diffraction patterns for the CdS, ZnS sample annealed in $N_{2}$ gas at $550^{\circ}C$. It was found hexagonal structure which had the lattice constant $a_{0}\;=\;4.1364{\AA}$, $c_{0}\;=\;6.7129{\AA}$ in CdS and $a_{0}\;=\;3.8062{\AA}$, $c_{0}\;=\;6.2681{\AA}$ in ZnS, respectively. Hall effect on these sample was measured by Van der Pauw method and then studied on carrier density and mobility depending on temperature. We measured also spectral response, sensitivity maximum allowable power dissipation and response time on these sample.

• The Journal of Natural Sciences
• /
• v.8 no.2
• /
• pp.119-127
• /
• 1996

The effect of sodium hydroxide treatment on some physicochemical properties of zeolite mordenite mineral was studied with chemical analyses, powder X-ray diffraction, thermal analyses, infrared analysis, measurement of carbon dioxide adsorption and gas chromatography. Mordenite mineral from tuffaceous rocks in Yeongil and Wolsung area was used as a starting material and treated with 0.1-5N NaOH aqueous solution at about $95^{\circ}C$ in the water bath for three hours.At the concentration of sodium hydroxide below 0.5N, all chemical compositions in the tuff were virtually insoluble and the mordenite structure did not change. At the concentration above 1N, the chemical compositions such as silica, alumina, etc., were dissolved. The dissolution ratio of silica was lager than that of alumina, and the ratio of silica to alumina in the tuff decreased sharply in the concentration range of 2 to 3N. Intensity of X-ray diffraction peak of mordenite (202) plane and the adsorbed amount of carbon dioxide also decreased with the increasing concentration of sodium hydroxide above 1N. These decreases corresponded to the degree of mordenite structure collapsed.The separation of gas chromatography of nitrogen, oxygen and carbon monoxide was not affected by the sodium hydroxide treatment, but elution peaks of methane and krypton tended to be broadened and their retention time was shortened. The elution peaks of both methane and krypton tended to be overlapped with those of nitrogen and oxygen.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.3-10
• /
• 1993

Polycrystalline CdS thin films were grown on ceramic substrate using a chemical bath deposition method. They were annealed at various temperature and X-ray diffraction patterns were measured by X-ray diffractometer in order to study CdS polycrystal structure. Using extrapolation method of X-ray diffraction patterns for the CdS samples annealed in $N_{2}$ gas at $550^{\circ}C$ it was found hexagonal structure whose lattice constants $a_{o}$ and $c_{o}$ were $4.1364{\AA}$ and $6.7129{\AA}$, respectively. Its grain size was about $0.35{\mu}m$. Hall effect on this sample was measured by Van der Pauw method and studied on carrier density and mobility defending on temperature. From Hall data, the mobility was likely to be decreased by piezo electric scattering at temperature range of 33K and 150k and by polar optical scattering at temperature range of 150K and 293K. We measured also spectral response, sensitivity (${\gamma}$), maximum allowable power dissipation and response time on these samples.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.81-86
• /
• 1993

Polycrystalline CdSe thin films were grown on ceramic substrate using a chemical bath deposition (CBD) method. They were annealed at various temperature and X-ray diffraction patterns were measured by X-ray diffractometer in order to study CdSe polycrystal structure. Using extrapolation method of X-ray diffraction patterns for the CdSe samples annealed in $N_{2}$ gas at $450^{\circ}C$ it was found hexagonal structure whose lattice parameters $a_{o}$ and $c_{o}$ were $4.302{\AA}$ and $7.014{\AA}$, respectively. Its grain size was about $0.3{\mu}m$. Hall effect on this sample was measured by Van der Pauw method and studied on carrier density and mobility depending on temperature. From Hall data, the mobility was likely to be decreased by piezo electric scattering at temperature range of 33 K and 200 K, and by polar optical scattering at temperature range of 200 K and 293 K. We measured also spectral response, sensitivity (${\gamma}$), maximum allowable power dissipation and response time on these samples.

• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.169-177
• /
• 1995

The diffusion barrier property of 100-nm-thick titanium nitride (TiN) film between Cu and Si was investigated using sheet resistance measurements, etch-pit observation, x-ray diffractometry, Auger electron spectroscopy, and transmission electron microscopy. The TiN barrier fails due to the formation of crystalline defects (dislocations) and precipitates (presumably Cu-silicides) in the Si substrate which result from the predominant in-diffusion of Cu through the TiN layer. In contrast with the case of Al, it is identified that the TiN barrier fails only the in-diffusion of Cu because there is no indication of Si pits in the Si substrate. In addition, it appears that the stuffing of TiN does not improve the diffusion barrier property in the Cu/TiN/Si structure. This indicates that in the case of Al, the chemical effect that impedes the diffusion of Al by the reaction of Al with $TiO_{2}$ which is present in the grain boundaries of TIN is very improtant. On the while, in the case of Cu, there is no chemical effect because Cu oxides, such as $Cu_{2}O$ or CuO, is thermodynamically unstable in comparison with $TiO_{2}$. For this reason, it is considered that the effect of stuffing of TiN on the diffusion barrier property is not significant in the Cu/ TiN/Si structure.

• Journal of the Microelectronics and Packaging Society
• /
• v.4 no.1
• /
• pp.1-12
• /
• 1997

본 연구에서는 용액성장법에 의해 양자 입자로 구성된 CdS 박막을 슬라이드 유리기 판위에 성장시키고 이들의 구조적 광학적 특성에 대하여 연구하였고 이들 결과를 토대로 용 액성장법으로 성장된 CdS 박막의 양자 사이즈 효과에 대하여 연구하였다. 성장시간은 1, 3, 10, 20분이었고 성장온도는 75$^{\circ}C$였다. X-선 회절 분석결과 본 연구에서 합성된 CdS 박막은 hexagonal상의 결정구조를 갖는 것으로 나타났고 성장시간에 따라 막의 투께는 61~195nm, 입자사이즈는 8.5~22.5nm로 나타났다. 광에너지 변화에 따른 투과도 측정결과 본 연구의 CdS 시료는 성장시간에 따라 에너지 밴드갭이 2.43~2.51 eV로 나타나서 벌크 CdS의 에너 지 밴드갭인 2.42 ev보다 높은 에너지 밴드갭을 갖게 되어 양자 사이즈 효과에 의한 blue shift 현상이 용액성장법에 의해 합성된 CdS 시료에도 존재한다는 것이 밝혀졌다 그리고 이 같은 용액성장법으로 성장된 CdS에 대해 최초로 수행된 Raman 산란 실험결과 이성장방법 으로 성장된 CdS에는 1TO, E2, 1LO 포논 모드가 존재함을 알수 있었고 또한 입자 사이즈 감소에 의한 1LO포논 모드의저주파수 shift 현상 즉 포논 모드의 softening 현상이 있음이 밝혀졌고 softening은 최대6.2%까지 발생하였다. 이와같은 높은 softening은 본연구의 CdS 박막 내 양자 입자의 입도가 작은것에 기인하는 것으로 밝혀졌다. 또한 본 CdS 시료의 양 자 사이즈 효과의 결과로 1TO 포논도 나타났는데 이 1TO 포논과 E2 포논의 Raman shift 는 성장시간 즉 막의 두께와는 무관한 것으로 나타났다.행렬모형(二重比例行列模型)을 이용하여, 산업구조의 변화로 인한 직업별 인력수요 변화가 충분히 고려되도록 하였다. 전망의 결과에 따르면 향후 우리 경제는 지식기반경제(knowledge-based economy)로 이행하고 있다고 볼 수 있다. 우선 산업구조면에서 지식집약적산업으로의 구조조정이 일어나게 되고 이에 따라 산업별 취업구조에서도 고기술산업의 취업준비중이 급속히 증가하게 된다. 직업별 취업분포에 있어서도 전문기술직 행정관리직 등의 고숙련 사무직의 비중은 크게 증가하는 반면 생산관련직과 농림어업직의 비중은 감소하게 된다. 이처럼 경제가 지식집약화되어 감에 따라 고학력자에 대한 수요는 지속적으로 증가하지만 현재 적절한 인력양성과 공급이 이루어지지 않고 있어 향후 기술이나 기능에 따른 수급부일정(需給不一政)(skill mismatch)현상이 매우 심해질 것으로 보인다. 따라서 앞으로의 인력정책에서 가장 주안점을 두어야 할 부분은 첨단기술산업과 관련된 인력의 양성에 있다고 하겠다.2시간까지 LPDG용액은 MEC용액보다 비교적 나은 회복을 보였고 재관류 3일과 7일의 폐기능 평가에서 두 용액 모두에서 폐기능의 점차적 소실을 보였으며 이는 병리조직검사에서 보듯이 폐혐에 의한 외적인 요소라고 생각되며 따라서 LPDG용액은 허혈재관류손상 방지 및 급성폐렴 등 염증을 잘 관리한다면 20시간 이상 LPDG용액의 안전한 폐보존의 가능성 을 얻을 수 있었다.ic 형태로 외래유전자가 발현되었지만 대조구에서 87.0% (26/30개) 배반포기가 $\beta$-Gal 활력을 보인 반면, G418 처리구에서는 모든 배반포기가 $\beta$-Gal 활력을 보였다 (P<0.05). 그러나 대조구 및 G418 처리구의 ICM