• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.51.2-51.2
• /
• 2005

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1529-1534
• /
• 2008

Recently, mixers are being widely used in the display and semiconductor company in order to mix the chemical materials. The mixer normally consists of shaft, hub, reduction gear, and driving motor. It is one of the key design factors to evaluate the dynamic characteristics caused by the rotation. In this study, the dynamic characteristics of the high speed mixer, such as vibration, noise and thermal radiation, are verified by the experiment. Through the experiment, it is shown that the structural unbalance mass of high speed mixer is the important source of the severe vibrations and maximum temperature is mixer bowl.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.430-437
• /
• 2006

The mixing effect is studied by comparing rotating and oscillating stirrers in the micro channel. The cases of Re=10 to 80 with various stirring speeds are considered to analysis the effect of Re and stirrer speed for the mixing. Under Re=20, the oscillating stirrer represents better mixing rate than the rotating stirrer up to the critical stirrer speed which has a maximum efficiency. Over Re=30, the results of oscillating and rotating stirrer show that the faster the stirrer speed, the higher the mixing effect within the concerned stirrer speed range and the oscillating stirrer keeps the higher mixing rate. It was found that the mixing effect is a function which has an optimum of the Reynolds number and the stirrer speed. The D2Q9 Lattice Boltzmann Method is used due to the merits of calculation for the unsteady flow with moving boundary.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.133-138
• /
• 2001

In this paper, we have investigated the drying characteristics of waste sludge in a rotary dryer equipped with disintegration device. The sludge samples($moisture\;contents\;:\;70{\sim}85%\;W.B.$) used in the experiment were mainly a soybean and an alcohol fermentation sludges in food industry, or sewage sludge. It was studied by measuring the change of moisture contents that the shaft speed($operating\;range\;:\;100{\sim}250rpm$) affected on the drying rate and the particle size distribution of the dried solid. The dried granular products of the diameter of 1 to 5mm are obtained from sludge materials. In the results, as the increased of shaft speed, the particle size and the moisture contents of dried solid was decreased, and the retention time was increased.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.3
• /
• pp.51-59
• /
• 2006

The physical characteristics of autonomic microcapsules manufactured with various agitation speeds in a stirred tank were observed experimentally by a particle size analyzer and an optical microscope. The flow characteristics in a stirred tank were also investigated through a 3-dimensional numerical simulation to understand the manufacturing process of autonomic microcapsules. According to the results, we found that the agitation speed was the important factor to determine the sizes of microcapsules. The impeller-induced flow allowed the jet and tip-vortex pair components in the mixed fluid of a stirred tank. The vorticity around the blades in the impeller was increased as increasing the agitation speed. In addition, the size of autonomic microcapsules was strongly affected on the small scale mixing pattern such as a tip-vortex pair.

• 한국가시화정보학회:학술대회논문집
• /
• 2007.11a
• /
• pp.138-142
• /
• 2007

본 연구는 고점도 유체의 혼합을 위한 교반기 설계의 기초연구로서 스크류 형상의 임펠러(또는 헬리컬 임펠러)를 가지는 교반기 내의 유동과 이에 따른 유체혼합 특성을 수치해석을 통해 가시화한 것이다. 이와 더불어 양호한 혼합효과를 가져다 줄 것으로 예상되는 엇갈림형 스크류 임펠러의 모델을 제안하였다. 수치해석상의 유체는 고점도의 Newton유체로 가정하였으며 임펠러의 회전속도는 6[rpm]으로 아주 작게 하여 저 레이놀즈수(약 Re=3)에서 혼합효과를 연구하였다. 또한 각종 설계 파라미터를 변화시켜 혼합 양상의 차이를 분석하여 설계에 반영하고자 하였다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.2
• /
• pp.125-131
• /
• 2009

An electrolytic system (zinc anode-gallium cathode) was setup to evaluate the performance of several stirrers prepared for this study, where stirrers have been used to prevent uranium from forming dendrite on the cathode in pyrochemical process. In the case of no-stirring condition, zinc dendrites began to grow on the gallium surface in 1 hour and some dendrite grew out of the cathode crucible around 6 hours. When a rectangular stirrer or a tilt stirrer was rotated, at 40${\sim}$150 rpm, to mix the liquid gallium cathode, dendritic growth of zinc metal was prevented irrespective of revolution speed, but some of the deposits overflowed out of the cathode crucible owing to the large centrifugal forces at 150 rpm. The harrow stirrer did not nearly retard the dendrite growth at 40 rpm, but the dendrite growth was retarded at higher than 100 rpm and the zinc deposits also did not overflow at 150 rpm. Pounder could also prevent the dendrite growth to some extent but it had some difficulties in operation compared with other types of stirrers.

• Journal of Energy Engineering
• /
• v.22 no.1
• /
• pp.28-37
• /
• 2013

Stirred tank is widely used in various industries for mixing operations and chemical reactions for single- or multi-phase fluid systems. For designing agitator of high performance, quantity data of internal flow characteristics influenced by mixing performance are definitely confirmed but quantity analysis about the transient flow characteristics of complicate structure is recognized as difficult problem in the present. In this study, two models of commercial CFD code Fluent 6.3 used to propose suitable for the tank analysis. Agitation of Stirred tank is analyzed using a mixed model and the flow in the stirred tank is analyzed using a standard k-${\varepsilon}$ model. Multiple reference frame(MRF) and Sliding mesh(SM), the analysis techniques were used For compare a result of CFD with a visualization experiment result, to grasp internal flow and mixing characteristic in stirred tank and to present fundamental analysis method.

• Korean journal of applied entomology
• /
• v.23 no.1 s.58
• /
• pp.37-41
• /
• 1984

The $100\%$ of insect pests on the imported logs and Sitophilus oryzae(L.) will be killed both when the imported logs are fumigated on shipboard with 25g methyl $bromide/m^3$ for 24hours at $10\~20^{\circ}C$ and when they are fumigated on shipboard with 37.5g methyl $bromide/m^3$ caculated by DT products for 16 hours at $10\~20^{\circ}C$ using 2 fans of 1800rpm over and ID 30cm. Without using fans, it takes $4\~6$ hours to make gas concentration even in hold. But using 2 fans per hold, the period reduces to $1\~3$ hours.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.419-420
• /
• 2020

본 논문에서는 전자기 교반 시스템용 2 상 직교하는 전원 공급 장치의 출력 전류 정상상태 오차를 줄일 수 있는 제어 기법을 제안하다. 2 상 직교하는 전원 공급 장치는 단상 풀브리지 인버터 2 대 대신 3 상 전압원 인버터 1 대를 사용하여 인버터의 레그 숫자가 줄어들고 인버터 스위치의 도통 손실이 감소한다. 본 논문에서는 회전 좌표계로의 변환(dq 변환)을 통해 출력전류 정상상태 오차를 0 으로 제어하는 기법을 제안한다. 본 논문에서는 제안하는 제어 기법의 유효성은 시뮬레이션을 통해 검증하였다.