• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.11-15
• /
• 2012

한국형발사체 상단엔진에 사용될 7톤급 액체로켓엔진용 터보펌프의 임계속도 해석이 이루어 졌다. 7톤급 터보펌프는 기 개발된 실험용 30톤급 터보펌프 및 현재 개발 중인 한국형발사체 1, 2단 엔진용 75톤급 터보펌프의 기본 개념을 채용하여 1축 터보펌프로 설계가 진행 중이다. 2개의 볼 베어링으로 지지되는 산화제펌프 회전체와 역시 2개의 볼 베어링으로 지지되는 연료펌프-터빈 회전체는 스플라인 축으로 연결되어 설계 속도에서 작동한다. 본 연구에서는 회전체동역학 해석을 수행하여 터보펌프가 sub-critical 회전체로서 충분한 임계속도 분리 여유를 확보하는 지를 검토하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.115-116
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2011년도 춘계학술대회 논문집
• /
• pp.1289-1290
• /
• 2011

• Tribology and Lubricants
• /
• 제32권4호
• /
• pp.107-112
• /
• 2016

This paper presents a rotordynamic analysis of the reduction gear system applied to the 250 kW super critical CO₂ cycle. The reduction gear system consists of an input shaft, intermediate shaft, and output shaft. Because of the high rotating speed of the input shaft, we install tilting pad bearings, rolloer bearings support the intermediate and output shafts. To predict the tilting pad bearing performance, we calculate the applied loads to the tilting pad bearings by considering the reaction forces from the gear. In the rotordynamic analysis, gear mesh stiffness results in a coupling effect between the lateral and torsional vibrations. The predicted Campbell diagram shows that there is not a critical speed lower than the rated speed of 30,000 rpm of the input shaft. The predicted modes on the critical speeds are the combined bending modes of the intermediate and output shaft, and the lateral vibrations dominate when compared to the torsional vibrations. The damped natural frequency does not strongly depend on the rotating speeds, owing to the relatively low rotating speed of the intermediate and output shaft and constant stiffness of the roller bearing. In addition, the logarithmic decrements of all the modes are positive; therefore all modes are stable.

• 한국정밀공학회지
• /
• 제25권3호
• /
• pp.83-92
• /
• 2008

This paper develops the theory for a fault-tolerant, permanent magnet biased, homopolar magnetic bearing. If some of the coils or power amplifiers suddenly fail, the remaining coil currents change via a novel distribution matrix such that the same magnetic forces are maintained before and after failure. Lagrange multiplier optimization with equality constraints is utilized to calculate the optimal distribution matrix that maximizes the load capacity of the failed bearing. Some numerical examples of distribution matrices are provided to illustrate the theory. Simulations show that very much the same dynamic responses (orbits or displacements) are maintained throughout failure events (up to any combination of 3 coils failed for the 6 pole magnetic bearing) while currents and fluxes change significantly. The overall load capacity of the bearing actuator is reduced as coils fail. The same magnetic forces are then preserved up to the load capacity of the failed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.306-310
• /
• 2014

The purpose of this study is the stability evaluation of a vacuum pump through modal test and rotor dynamics. Eigenvalue was solved by the finite-element method(FEM) using 2D and 3D models, then the modal test result was compared with the FEM result. According to the comparison, the analysis result using the 2D was more accurate than the 3D model. Therefore, rotor dynamics was performed by the 2D model. Campbell diagram and root-locus maps, which were calculated by complex-eigenvalue analysis, were used to evaluate the stability of the rotors of the vacuum pump. And displacement solved by unbalance response analysis was compared with the minimum clearance between two rotors of the vacuum pump. Thus, the vacuum pump is assumed operated under steady state through the evaluation of the rotor dynamics.

• 한국유체기계학회 논문집
• /
• 제12권3호
• /
• pp.26-30
• /
• 2009

This paper predicts the critical speeds of a 5MW industrial gas turbine by using commercial rotordynamic tool, DYNAMICS 4.3. The gas turbine is operated at 12,975 rpm on squeeze film dampers. The stiffness of the squeeze film dampers are estimated. The critical speeds of the gas turbine rotor are calculated to have a sufficient separation margin (2%) from the 1st bending mode and pass over 2 rigid body modes below 4,000 cpm. This paper discussed the coupling effects on the dynamic response of the gas turbine.

• 한국유체기계학회 논문집
• /
• 제13권3호
• /
• pp.18-23
• /
• 2010

This paper predicts the unbalance and transient (start-up) response of a 5MW industrial gas turbine by using commercial rotordynamic tool, DYNAMICS 4.3. The gas turbine is operated at 12,975rpm on squeeze film dampers or tilting pad bearings. The stiffness and damping coefficients of the squeeze film dampers and tilting pad bearings are estimated. It is seen that the vibration amplitude of the gas turbine rotor is sufficiently small around the critical speeds and at the rated speed.

• 대한기계학회논문집A
• /
• 제32권12호
• /
• pp.1096-1101
• /
• 2008

When we design a controller for the active magnetic bearings that support a large rotor, it is important to have an accurate model of the rotor. For the case of the flywheel that is used to store energy, an accurate rotor model is especially important because the dynamics change with respect to the running speed due to gyroscopic effects. In this paper, we present a procedure of obtaining an accurate rotor model of a large flywheel energy storage system using finite-element method. The model can predict the first and the second bending mode which match well with the experimental results obtained from a prototype flywheel energy storage system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 추계학술대회 논문집
• /
• pp.764-765
• /
• 2011

In this paper, rotordynamic analyses of the Campbell diagram, critical speeds, and harmonic responses for a TMP rotor system are performed. Since the finite element model of the TMP rotor system has a very large number of degrees of freedom because of its complex geometry, and dynamic analyses for investigating the critical speeds, stability, and harmonic response are repeated for various design parameters, model order reduction (MOR) is necessary to reduce the computational cost. The Krylov-based model order reduction via moment matching significantly speeds up the rotordynamic analyses for the TMP rotor system.