• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.1
• /
• pp.751-758
• /
• 2021

Munitions must be analyzed to identify any risks for quality assurance in development and mass production. Risk identification for parts, compositions, and systems is carried out through failure mode effects analysis (FMEA) as one of the most reliable methods. FMEA is a design tool for the failure mode of risk identification and relies on the RPN (risk priority number). FMEA has disadvantages because its severity, occurrence, and detectability are rated at the same level. Fuzzy FMEA applies fuzzy logic to compensate for the shortcomings of FMEA. The fuzzy logic of Fuzzy FMEA is to express uncertainties about the phenomenon and provides quantitative values. In this paper, Fuzzy FMEA is applied to the failure mode of a rotorcraft landing system. The Fuzzy rule and membership functions were conducted in the Fuzzy model to study the RPN in the failure mode of a landing system. This method was selected to demonstrate crisp values of severity, occurrence, and detectability. In addition, the RPN was obtained. The results of Fuzzy FMEA for the landing system were analyzed for the RPN and ranking by fuzzy logic. Finally, Fuzzy FMEA confirmed that it could use the data in quality assurance activities for rotorcraft.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.774-780
• /
• 2021

The auxiliary power unit (APU) of a rotorcraft starts the engine during operation/flying. The APU is composed of a gas turbine engine type. The starting principle of the component is that the electric start motor generates the power required for starting by rotating the shaft. In this study, quality improvement was performed by applying an over-running clutch (ORC) between the APU and the starter motor to secure the operability of the starter motor of the APU mounted on the rotorcraft. The starter motor has the main role of starting the APU, but during operation, it is rotated without load by the rotational force of the APU gear shaft, resulting in friction at the brush. This phenomenon causes abrasion of the brush of the starter motor. Consequently, when the APU operation time increases, the brush life decreases, and the operability of the APU is affected. In this study, an ORC that separates the interlocking between the start motor brush abrasion and the APU operation time was applied to improve the operability/durability of the APU starter motor. The effect was verified through a test, and the technical feasibility of the design change was analyzed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.9
• /
• pp.671-680
• /
• 2020

This paper describes an improved beam analysis for compound rotorcraft fuselage design. The present beam approach is capable of analyzing fuselage composed of stiffeners using equivalent layer methodology. Thickness of the skin and laminated layer approach are suggested based on the unified beam formulation. The analysis which considers an equivalent stiffener layer is performed for a fuselage with stiffeners and preliminary study about the specification of stiffeners is conducted and compared by the results using the existing software.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.76-84
• /
• 2021

The quality assurance activities can detect the factors that affect the quality based on risk identification in the course of mass production. Risk identification is conducted with risk analysis, and the risk analysis method for the rotorcraft landing system is selected by failure mode effects analysis (FMEA). FMEA is a method that detects the factors that can affect the product quality by combining severity, occurrence, and detectability. The results of FMEA were prioritized using the risk priority number. On the other hand, these methods have certain shortcomings because the severity, occurrence, detectability are weighted equally. Dempster-Shafer evidence theory can conduct uncertainty analysis for the opinions with personal reflections and subjectivity. Based on the theory, the belief function and the plausibility function can be formed. Moreover, the functions can be utilized to evaluate the belief rate and credibility. The system is exposed to impact during take-off and landing. Therefore, experts should manage failure modes in the course of mass production. In this paper, FMEA based on the Dempster-Shafer evidence theory is discussed to perform risk analysis regarding the failure mode of the rotorcraft landing system. The failure priority was evaluated depending on the factor values. The results were derived using belief and plausibility function graphs.

• Journal of Aerospace System Engineering
• /
• v.14 no.spc
• /
• pp.39-48
• /
• 2020

This paper deals with the process of estimating the environmental noise generated from the actual flying aircraft using the noise measurement results obtained through the wind tunnel test and verifying it through flight tests. In order to evaluate the environmental noise of an aircraft, noise tests and evaluations are generally conducted according to the procedures prescribed by the International Civil Aviation Organization (ICAO). In this paper, we introduced environmental noise evaluation method that can be applied to composite both fixed-wing aircraft and multi-copter, and introduced the evaluation method by experiment. This paper introduces the process of simulating the noise test results measured in the wind tunnel test using real flight test results. In addition, in consideration of flight operating conditions and noise measurement methods proposed by the ICAO, the effective perceived noise level (EPNL) was predicted by performing both the wind tunnel test and the aircraft flight test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.3
• /
• pp.127-132
• /
• 2005

In order to investigate transient behavior, of the CRW(Canard Rotor Wing) type UAV(Uninhabited Aerial Vehicle) propulsion system during flight mode transition considering flow control valve operation, the propulsion system was modelled using SIMULINK commercial program. The valve system is to control the gas flow of the rotary duct system and the main duct system, and the analysis was performed with an assumption that the total gas mass flow of the main engine is the same as summation of the rotary duct flow and the main duct flow, and with consideration of valve loss, flow rate and effective area in valve angle variation. The performance analysis was carried out during flight mode transitions from the rotary flight mode to the fixed wing flight mode and vice versa mode at altitude of 1km, flight Mach number 0.1 and maximum engine rpm.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.5
• /
• pp.477-481
• /
• 2010

Some rotorcraft fuel tanks are required to be self-sealing and crashworthy for enhancing the survivability of crews. Self-sealing capability prevents the fuel leakage through contacting fuel with self-sealing material when the tank wall is penetrated by projectiles such as bullets. US army established MIL-DTL-27422D which specifies the detail requirements related to gunfire resistant fuel tank especially for military rotorcraft. The Fuel tanks for Korea Helicopter Program have been developed in accordance with MIL-DTL-27422D. The Self-sealing capability of the fuel tanks has been confirmed by the gunfire resistance test which specified on the MIL-DTL-27422D.

• Journal of Aerospace System Engineering
• /
• v.14 no.1
• /
• pp.28-35
• /
• 2020

This paper presents the design improvements made for the crack which is in the mounting structure of the mechanical structure of rotary wing aircraft. The doubler added to the mounting structure of rotary wing aircraft was designed and manufactured based on the load at the development stage, and a crack was found in the surface of doubler at a certain point during the operation of the aircraft. To identify the cause of the crack, the initial deformation of the structure, which may occur as a result of fastening condition, was considered and the dynamic analysis of the natural frequency of the structure comparing to the blade passing frequency of the aircraft were additionally reviewed. As a result of this study, a shim was added to remove the physical gap of the fastening area, and a doubler with thickened reinforcement was installed. The increase of structural strength is shown by reviewing the results of dynamic analysis for the structural verification of the improved design, and the fatigue evaluation complied to the requirement of the aircraft lifetime.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.35 no.6
• /
• pp.535-544
• /
• 2017

UAVs (Unmanned Aerial Vehicle) are generally classified into fixed-wing and rotary-wing type, and both have very different flight characteristics each other during photographing. These can greatly effect on the quality of images and their productions. In this paper, the change of the camera rotation angle at the moment of photographing was compared and analyzed by calculating orientation angles of each image taken by both types of payload. Study materials were acquired at an altitude of 130m and 260m with fixed-wing, and at an altitude of 130m with rotary-wing UAV over an agricultural land. In addition, an accuracy comparison of boundary surveying methods between UAV photogrammetry and terrestrial cadastral surveying was conducted in two parcels of the study area. The study results are summarized as follows. The differences at rotation angles of images acquired with between two types of UAVs at the same flight height of 130m were significantly very large. On the other hand, the distance errors of parcel boundary surveying were not significant between them, but almost the same, about within ${\pm}0.075m$ in RMSE (Root Mean Square Error). The accuracy of boundary surveying with a fixed-wing UAV at 260m altitude was quite variable, $0.099{\sim}0.136m$ in RMSE. In addition, the error of area extracted from UAV-orthoimages was less than 0.2% compared with the results of the cadastral survey in the same two parcels used for the boundary surveying, In conclusion, UAV photogrammetry can be highly utilized in the field of cadastral surveying.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.5
• /
• pp.458-465
• /
• 2011

UAV-UGV teaming concept has been proposed that can compensate for weak points of each platform by providing carrying, launching, recovery and recharging capability for the VTOL-UAV through the host UGV. The teaming concept can expand the observation envelop of the UGV and extend the operational capability of the UAV through mechanical combination of each system. The spherical-shaped coaxial rotorcraft UAV is suggested to provide flexible and precise interface between two systems. Hybrid navigation solution that included vision-based target tracking method for precision landing is investigated and its experimental study is performed. Feasibility study on length-variable rotor to provide the compact configuration of the loaded rotorcraft platform is also described.