• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.21-27
• /
• 2009

In this study, experimental findings on the resistance to magnesium sulfate attack of portland cement mortar and paste specimens incorporating metakaolin (MK) are presented. Specimens with four replacement levels of metakaolin (0, 5, 10 and 15% of cement by mass) were exposed to solutions with concentrations of 0.424% and 4.24% as $MgSO_4$ at ambient temperature. The resistance of mortar specimens was evaluated through visual examination and linear expansion measurements. Additionally, in order to identify the products formed by magnesium sulfate attack, microstructural analyses such as XRD, DSC and SEM/EDS were also performed on the paste samples incorporating metakaolin. Results confirmed that mortar specimens with a high replacement level of metakaolin exhibited lower resistance to a higher concentration of magnesium sulfate solution. It was found that the negative effect of metakaolin on the magnesium sulfate attack is partially attributed to the formation of gypsum and thaumasite. Conclusively, it is necessary to pay a special attention when using metakaolin in concrete structures, particularly under highly concentrated magnesium sulfate environment.

• Resources Recycling
• /
• v.25 no.4
• /
• pp.32-41
• /
• 2016

The precipitation test, which is the last step of magnesium recovery process consisting of three processes (pre-precipitation, selective dissolution of magnesium, precipitation) is performed to obtain magnesium sulfate powder from seawater. In the study, we succeed in precipitating the magnesium sulfate by adding acetone into the solution of magnesium over 4 times concentrated from seawater. The yield efficiency of magnesium sulfate increases with increasing pH and the ratio of added acetone. More than 99% of magnesium is obtained as magnesium sulfate hydrate ($MgSO_4{\cdot}6H_2O$) under the following conditions; pH 1.0 ~ 1.5, and the ratio of solution and acetone 1 : 1.5 (v:v). The acetone used in the precipitation process is recovered by the fractional distillation.

• Journal of the Korea Institute of Building Construction
• /
• v.22 no.6
• /
• pp.663-672
• /
• 2022

The purpose of this study is to evaluate the magnesium sulfate resistance of a geopolymer mixed with rice husk powder. General concrete, silica fume mixed concrete, and binary blended geopolymer were selected as comparison targets to confirm the magnesium sulfate resistance, and sulfate deterioration was calculated using the compressive strengths with ages. In addition, the weight change rate and the relative dynamic coefficient of the geopolymer were comparatively analyzed, and the degree of etteringite formation was confirmed using X-ray diffraction analysis. the experiment, the geopolymer mixed with 10% rice husk powder showed 10.8% higher compressive strength than concrete with silica fume when submerged for 56 days. Also, the geopolymer mixed with rice husk powder showed a small weight change rate of 0.9 to 1.45%. composition after immersion in magnesium sulfate through X-ray diffraction analysis, it was observed that a small amount of ettringite was dispersed in the geopolymer containing rice husk powder. Thus, there is a high correlation with the corrosion resistance of magnesium sulfate

• Magazine of the Korea Concrete Institute
• /
• v.10 no.5
• /
• pp.117-128
• /
• 1998

화학적으로 유해한 환경에 놓인 콘크리트 구조물은 필연적으로 그 기능이 악화되므로 혼화재를 포함한 고강도 콘크리트 또는 혼화재 그 자체가 화학물질에 오염된 환경하에서 어떤 변화를 일으키는가에 대한 연구의 필요성이 점점 증대되고 있다. 따라서 본 논문에서는 건설현장에서 가장 흔히 사용되는 보통강도 콘크리트와 실리카-흄을 포함한 포틀랜드시멘트 경화체인 고강도 콘크리트가 황산염의 침해를 받는 경우에 일어나는 강도특성과 물성변화를 조사하기 위하여 담수와 함께 황산나트륨, 황산마근네슘, 황산나트륨과 황산마그네슘의 혼합용액 등 여러종류의 황산염 용액에 실리카-흄을 사용한 고강도 콘크리트, 낮은 물-시멘트 비의 고강도 콘크리트, 보통강도의 콘크리트 등의 시험체들을 270일간 침지시켜 침지시간에 따른 압축강도 변화와 실리카-흄의 첨가량에 따른 압축강도 변화, 그리고 실리카-흄의 첨가량에 따른 선형팽창량 및 중량변화등에 관한 실험을 수행하였다. 이에 대한 실험결과를 토대로 실리카-흄을 사용한 고강도 콘크리트에 황산염이 미치는 영향을 분석하여 고강도 콘크리트의 실용성을 극대화하기 위한 방안에 대하여 고찰해보았다. 그 결과 실리카-흄을 포함한 고강도 콘크리트는 황산나트륨의 침해에 대해서는 강한 저항성을 나타내지만 황산마그네슘에 대해서는 심각한 침해를 일으키는 것으로 나타났으므로 황산마그네슘에 노출될 우려가 있는 콘크리트 구조물에 고강도를 발현하기 위하여 실리카-흄을 사용하는 것은 구조적으로 큰 문제가 발생할 것으로 사료된다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.6
• /
• pp.55-62
• /
• 2008

This paper reports the effect of replacement levels of silica fume on the resistance to magnesium sulfate attack. Mortar specimens incorporating silica fume were exposed to 5% magnesium sulfate solution for 360 days at ambient temperature. The main variable was the replacement levels of silica fume(0, 5, 10 and 15% of cement by mass). The resistance of mortar specimens incorporating silica fume against magnesium sulfate attack was regularly monitored by measuring compressive strength and expansion. In addition, in order to investigate the reactants formed by magnesium sulfate attack, various instrumental analyses such as XRD, SEM and DSC were used. Results demonstrated that the formation of gypsum, thaumasite and brucite led to a significant deterioration due to magnesium sulfate attack in cement matrix incorporating silica fume.

• Journal of Chest Surgery
• /
• v.39 no.5 s.262
• /
• pp.366-375
• /
• 2006

Background: Hypomagnesemia is a common complication after cardiac surgery with cardiopulmonary bypass. The purpose of this study was to assess the clinical beneficial effect of administration of magnesium sulfate in cardiac surgery. Material and Method: Thirty five patients scheduled for elective cardiac surgery were randomly assigned to magnesium group (n=20) which received magnesium sulfate in priming solution (1 g) and cardioplegic solution (1 g) or control group (n=15) which did not receive it. Arterial blood samples were drawn for measuring $Mg^{++}$ and electrolytes contents, blood gas analysis, CBC, total protein, albumin, blood urea nitrogen (BUN), creatinine, alanine aminotransferase (ALT), aspartate aminotransferase (AST), total bilirubin, tumor necrosis factor-${\alpha}$ $(TNF-{\alpha})$, interleukin-6 (IL-6), interleukin-10 (IL-10), creatine phosphokinase (CpK), creatine kinase-MB (CK-MB), lactate dehydrogenase(LDH), troponin-1 (TNI), prothrombin time (PT) and activated pratial thromboplastin time level (aPTT). Venous blood samples were drawn before and after the operation for measuring activated clotting time level (ACT). Result: $Mg^{++}$ levels in magensium group were higher than those of control group at intraoperative and post-operative periods (p<0.05). dysrhythmias were lower in magnesium group (8 cases out of 17 patients, 46.4%) than in control group (10 cases out of 10, 100%, p=0.050). Conclusion: These results showed that administration of low dose magnesium sulfate during cardiac surgery prevented hypomagnesemia and lowered incidence of dysrhythmia.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.94-101
• /
• 2016

This paper presents an investigation into the durability alkali-activated materials(AAM) mortar and paste samples manufactured using fly-ash(FA) and ground granulated blast furnace slag(GGBFS) exposed to a sulfate environment with different GGBFS replace ratios(0, 30, 50 and 100%), sodium silicate modules($Ms[SiO_2/Na_2O]$ 1.0, 1.5 and 2.0) and initial curing temperatures($23^{\circ}C$ and $70^{\circ}C$). The tests involved immersions for a period of 6 months into 10% solutions of sodium sulfate and magnesium sulfate. The evolution of compressive strength, weight, length expansion and microstructural observation such as x-ray diffraction were studied. As a results, as higher GGBFS replace ratio or Ms shown higher compressive strengths on 28 days. In case of immersed in 10% sodium sulfate solution, the samples shows increase in long-term strength. However, for samples immersed in magnesium sulfate solutions, the general observation was that the compressive strength decreased after immersion. The most drastic reduction of compressive strength and expansion of weight and length occurred when GGBFS or Ms ratios were higher. Also, the XRD analysis of samples immersed in magnesium sulfate indicated that expansion of AAM caused by gypsum($CaSO_4{\cdot}2H_2O$); the gypsum increased up to 6 months continuously.

• Journal of the Korea Concrete Institute
• /
• v.22 no.2
• /
• pp.219-228
• /
• 2010

It has been well known that concrete structures exposed to acid and sulfate environments such as sewer, sewage and wastewater, soil, groundwater, and seawater etc. show significant decrease in their durability due to chemical attack. Such deleterious acid and sulfate attacks lead to expansion and cracking in concrete, and thus, eventually result in damage to concrete matrix by forming expansive hydration products due to the reaction between portland cement hydration products and acid and sulfate ions. Objectives of this experimental research are to investigate the effect of mineral admixtures on the resistance to acid and sulfate attack in concrete and to suggest high-resistance concrete mix against acid and sulfate attack. For this purpose, concretes specimens with three types of cement (ordinary portland cement (OPC), binary blended cement (BBC), and ternary blended cement (TBC) composed of different types and proportions of admixtures) were prepared at water-biner ratios of 32% and 43%. The concrete specimens were immersed in fresh water, 5% sulfuric acid, 10% sodium sulfate, and 10% magnesium sulfate solutions for 28, 56, 91, 182, and 365 days, respectively. To evaluate the resistance to acid and sulfate for concrete specimens, visual appearance changes were observed and compressive strength ratios and mass change ratios were measured. It was observed from the test results that the resistance against sulfuric acid and sodium sulfate solutions of the concretes containing mineral admixtures were much better than that of OPC concrete, but in the case of magnesium sulfate solution the concretes containing mineral admixtures was less resistant than OPC concrete due to formation of magnesium silicate hydrate (M-S-H) which is non-cementitious.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.1
• /
• pp.109-116
• /
• 2017

This paper describes the investigation into the durability alkali-activated materials(AAM) mortar and paste samples manufactured using fly-ash(FA) and ground granulated blast furnace slag(GGBFS) exposed to a sulfate environment with different GGBFS replace ratios(30, 50 and 100%), sodium silicate modules($Ms[SiO_2/Na_2O]$ 1.0, 1.5 and 2.0). The tests involved immersions into 10% sodium sulfate solution($Na_2SO_4$), 10% magnesium sulfate solution($MgSO_4$), 10% magnesium nitrate solution($Mg(NO_3)_2$) and 5% magnesium nitrate($Mg(NO_3)_2$+5% sodium sulfate solution+$Na_2SO_4$). The evolution of compressive strength, weight, length expansion and microstructural observation such as x-ray diffraction were studied. As a results, in case of immersed in $Na_2SO_4$, $Mg(NO_3)_2$ and $Mg(NO_3)_2+Na_2SO_4$ shows increase in long-term strength. However, for samples immersed in $MgSO_4$, the general observation was that the compressive strength decreased after immersion. The most drastic reduction of compressive strength and expansion of weight and length occurred when GGBFS or Ms ratios were higher. Also, the XRD analysis of samples immersed in magnesium sulfate indicated that expansion of AAM caused by gypsum($CaSO_4{\cdot}2H_2O$) and brucite(MgOH). The results showed that, an additional condition $Mg^{2+}$ in which ${SO_4}^{2-}$ is the presence of a certain concentration, sulfate erosion has to be accelerated.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.183-189
• /
• 2010

It is of importance to separate Ni(II) and Co(II) from Mg(II) in solution which was leached from nickel laterite ore. In order to investigate the possibility of separating Ni(II) and Co(II) from Mg(II), adsorption behavior of the three metals from individual and mixed sulfate solutions was investigated by using Diphonix resin. The concentration of each metal in solution was fixed at 100 ppm and the pH of the sulfuric acid solution was changed from 5 to 7. At ambient temperature, the adsorption behavior of the three metal ions followed Langmuir adsorption isotherm. The loading capacity of Diphonix resin for the three metal ions was obtained from the Langmuir isotherm. Since adsorption behavior of the three metal ions from the mixed solution was similar to each other, it was found to be difficult to separate Ni(II) and Co(II) from Mg(II) by using Diphonix resin.