• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.2
• /
• pp.199-206
• /
• 2008

Simultaneous nitrification and denitrification means that nitrification and denitrification occur concurrently in the same reaction vessel under low DO concentration. Some mathematical models developed to simulate simultaneous nitrification and denitrification reaction, but they have the complex model structures or have limitations of model application. To solve these problems, if possible that predict the behavior of simultaneous nitrification and denitrification reaction by activated sludge model, structures of the model is less complex than previous models and applies the various operation conditions. But original activated sludge models have difficulties in representing the denitrification reaction under aerobic condition. So the aim of this study is to interpret simultaneous nitrification and denitrification reaction by modifying activated sludge model. Original activated sludge model No.1(ASM1) was selected and modified. The simulation result in modified ASM1 predicted appropriately for the measured data. This indicates the structures of ASM1 are properly improved for interpretation of simultaneous nitrification and denitrification reaction.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.11
• /
• pp.2017-2023
• /
• 2000

A dynamic model was applied to compare the environmental parameters and effluent characteristics of refinery wastewater in activated sludge treatment. The measured DO, pH, MLSS, and COD values were compared with the simulated their results in the activated sludge reactor. As results of simulation. good agreements between the measured and simulated results were investigated. The simulated and measured effluent COD were 19.0~19.4mg/L and 23.1mg/L. respectively. The simulated and measured DO were 1.9~2.4mg/L and 2.2mg/L. respectively.

• The Journal of the Korea Contents Association
• /
• v.9 no.10
• /
• pp.444-450
• /
• 2009

We have investigated biosorption kinetics and equilibrium of $Pb^2+$ and $Cr^2+$ using waste sludge, and separation efficiency of waste sludge by dissolved air flotation was evaluated in the various A/S ratio. The biosorption capacity and contact time were shown as a simulation of biosorption equilibrium and kinetics models. Biosorption equilibrium of the $Pb^2+$ and $Cr^2+$ onto the waste sludge could be fitted by the Langmuir, Freundlich, Redlich-Peterson, and Koble-Corrigan equation. The kinetics could be fitted by a pseudo-second-order rate equation more than a pseudo-first-order rate equation. The separation efficiency of waste sludge using DAF was kept above 90%.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.409-413
• /
• 2005

A method to estimate the autotrophic maximum specific growth rate is presented in this paper. First of all, the concentration of nitrifier is simulated based on the amount of N nitrified, the sludge age and the default value for the decay coefficient. Secondly the OUR of the sludge with access of ammonia is measured. The maximum specific growth rate can be calculated as ${\mu}_{max,A}\;=\;OUR_{max,A}/Y_A$. It was demonstrated that the maximum specific growth rate of autotrophic biomass is not a constants but a time variable parameter. It is concluded that using $OUR_{max,A}$ for dynamic estimating maximum specific growth rate is a good approach and that using a constant value for the maximum specific growth rate over a longer period of time could not predict the performance of activated sludge plants.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.1
• /
• pp.97-104
• /
• 2010

At present, the biological nutrient removal (BNR) process for removal of nitrogen and phosphorus is being constructing to keep pace with the reinforced standard of effluent quality and the traditional activated sludge process of preexistence is being promoting to retrofit. At the most case of retrofitting, processes are subjected to be under consideration as alternative BNR process for retrofitting. However, process evaluation methods are restricted to compare only treatment efficiency. Therefore, when BNR process apply, process evaluation was needed various method for treatment efficiency as well as sludge production and aeration cost, and all. In this study, the evaluation method of alternative process was suggested for the case for retrofitting S wastewater treatment plant which has been operated the standard activated sludge process. Three BNR processes for evaluation of proper alternatative process were selected and evaluated with suggested method. The selected $A^2$/O, VIP and DNR processes were evaluated using the mathematical model which is time and cost effective as well as gathered objective evaluation criteria. The evaluation between 5 individual criteria was possible including sludge production and energy efficiency as well as treatment performance. The objective final decision method for selection of optimal process was established through the fuzzy inference.

• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.2
• /
• pp.153-162
• /
• 2021

The effects of activated carbon originated Ballasted Flocculant (BF) on the settleability of activated sludge and the recovery of BF by Hydro-cyclone (HC) were analyzed experimentally. Two kinds of BF (M-I: 125-250 ㎛, M-II: 250-425 ㎛ in dia.) and three kinds of activated sludges with different SS concentration (2,300-7,100 mg/L) were applied for this study. With the dosage variation of BF from 0.14 to 1.3 g-BF/g-SS, we could obtain 24-31% improvement in SV30 (Sludge Volume after 30min sedimentation) for the lowest SS concentration sludge (2,300 mg/L). Whereas the SV30 improvement was much higher as 44-48% for the highest SS concentration sludge (7,100 mg/L). The settling characteristics of the sludge with BF followed Vesilind model the best among three models (Vesilind, Takacs and Cho model). HC could effectively separate BF with the separation efficiency of 70-90% and over 95% separation efficiency could be obtained when the HC was applied twice.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.5
• /
• pp.548-555
• /
• 2007

The control of wastewater treatment has two merits; one is to regulate water quality of effluent and the other is to reduce the cost of wastewater treatment. The purpose of this study was to control the ammonium nitrogen in effluent that is known to cause eutrophication. The control was based on simplified ASM No. 1 which had 3 component materials and 8 coefficients, and the control method was as following. Firstly the ammonium concentration of inflow was measured and the optimal aeration time in effluent was determined according to simplified ASM No. 1 to be 1.0 mg/L. If ammonium concentration of effluent was not equal to 1.0 mg/L, the influent ammonium was corrected by adaptive control. These processes above were repeatedly performed. The SBR running aerobic-anoxic phase had been controlled for 1 month with this method. As a result, the ammonium concentration of the effluent showed in the range of $0.22\sim3.1$ mg/L with an average concentration of 1.1 mg/L. The adaptive control method used in this study was found very useful to control and predict the effluent concentration of ammonium.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2007.05a
• /
• pp.810-813
• /
• 2007

본 논문에서는 맥락 인식 (context-aware) 애플리케이션 개발에 있어서 사용자의 맥락 정보를 보다 효과적으로 처리할 수 있는 사용자 중심의 맥락 모델을 제안한다. 유비쿼터스 컴퓨팅 개념의 확산과 함께 맥락 인식 애플리케이션들에 관한 많은 연구가 진행되고 있다. 하지만, 맥락에 대한 정의는 여전히 모호하며, 애플리케이션들 마다 서로 다른 형태의 맥락을 활용하고 있기 때문에, 맥락에 대한 보다 구체적인 정의와 다양한 애플리케이션에 활용 가능한 형태의 맥락 모델이 필요하다. 제안된 사용자 중심의 맥락 모델에서는 사용자가 애플리케이션과 상호작용할 때 사용자의 직접적인 명령을 제외한 사용자와 관련된 정보를 맥락으로 정의한다. 또한, 제안된 사용자 중심의 맥락은 5W1H 형태로 구조화한 맥락요소 (ContextElement), 맥락 요소들을 편리하게 처리할 수 있는 연산자들을 포함하는 맥락 (Context), 그리고 단편적인 맥락 정보뿐만 아니라 기존의 맥락 정보까지도 활용할 수 있는 맥락메모리 (ContextMemory)로 구성된다. 특히, 다양한 센서들로부터 획득된 정보를 맥락 모델의 인터페이스를 통해서 맥락 인식 애플리케이션에서 활용할 수 있기 때문에, 서로 다른 맥락 인식 애플리케이션들을 개발함에 있어서도 동일한 맥락 모델을 사용할 수 있는 장점이 있다. 제안된 맥락 모델의 유용함을 보이기 위해서, 센서로부터 획득된 맥락 정보를 처리하는데 소요되는 시간을 측정하는 실험을 하였다. 따라서 제안된 사용자 중심의 맥락 모델은 사용자와 맥락 인식 애플리케이션간 자연스러운 상호작용을 지원할 것으로 기대된다.) kcal/mol의 생성활성화 에너지 감을 나타내었고, TGA로부터의 분해활성화 에너지는 각각 31.94, 30.84, 24.16 kcal/mol의 값을 나타내었다.로 감소되었다(35.2% vs. 77.4%; p<0.01). 실험 2에서 다양한 정자 농도에 의한 정자 침투율과 정상 수정률을 바탕으로 판단했을 때 $4.6{\times}10^6/ml$의 정자 농도가 다른 정자 농도에 비해 난구 세포부착 난자의 체외 수정에 적합한 것으로 나타났다. 체외 수정과정에서 난구 세포 부착된 상태로 수정된 난자는 나화 난자에 비해 유의적으로(p<0.05) 높은 분할률(48.8% vs. 58.9%), 배반포 형성률(11.0% vs. 22.8%)과 배반포 세포수$(22{\pm}2\;vs.\;29{\pm}2)$를 나타내었다. 본 연구의 결과로부터 돼지의 체외 수정과정에서 난구 세포의 존재는 정자 침투를 저해하지만 분할률, 배반포 형성률 및 배반포의 세포수를 증가시키는 것으로 사료된다.수의 유출입 지점에 온도센서를 부착하여 냉각수의 온도를 측정하고 냉각수의 공급량과 대기의 온도 등을 측정하여 대사열의 발생을 추정할 수 있었다. 동시에 이를 이용하여 유가배양시 기질을 공급하는 공정변수로 사용하였다 [8]. 생물학적인 폐수처리장치인 활성 슬러지법에서 미생물의 활성을 측정하는 방법은 아직 그다지 개발되어있지 않다. 본 연구에서는 슬러지의 주 구성원이 미생물인 점에 착안하여 침전시 슬러지층과 상등액의 온도차를 측정하여 대사열량의 발생량을 측정하고 슬러지의 활성을 측정할 수 있는 방법을 개발하였다.enin과

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.4
• /
• pp.409-420
• /
• 2007

ASM No. 1 is a very useful model to analyze wastewater treatment system removing organic carbon and nitrogen material. But it isn't adequate to control the wastewater treatment system with real time since it has many material divisions and parameters. So, the purpose of this study is the simplification of ASM No. 1 to control the wastewater treatment system. ASM No. 1 was changed with the model which has 3 material divisions(COD, $NH_4{^+}$, $NO_3{^-}$) and two phases(Aerobic and Anoxic condition). SBR was running with two phases(Phase I and II). Phase II running 20 minutes with aerobic time was used for deciding model parameters and Phase I running 12 minutes with aerobic time was used for proving the simplified model. The simplified model was compared with ASM No. 1 using data of Phase I and II. As a result of model comparison, the simplified model has enough ability to express the variation of $NH_4{^+}$ compound.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.6
• /
• pp.889-896
• /
• 2012

In this study, simulation results of nitrogen and phosphorus removals and microbial activities for an $A_2O$ process in wastewater treatment plant are presented by using Activated Sludge Models (ASMs). Simulations were performed using pre-calibrated model and layout implemented in GPS-X simulation software. The models were used to investigate variations of SRT, water temperature, DO and C/N ratio effect on nutrients removal and microbial activity. According to the simulated results, the successful nitrification required SRT higher than 10.3 days, whereas increase of $NO_3$-N loading in the anaerobic reactor caused phosphorus release by PAOs; the effluent $NH_4$-N showed rapid change between $12^{\circ}C$(21.7 mg/L) and $13^{\circ}C$(3.2 mg/L); the effluent phosphorus was increased up to 1.9 mg/L at water temperature of $25^{\circ}C$; the DO increase was positive for heterotrophs and autotrophs growths but negative for PAOs growth; the PAOs showed low activity when C/N ratio was lower than 2.5. The experimental results indicated that the calibrated models can assure the prediction quality of the ASMs and can be used to optimize the $A_2O$ process.