• Economic and Environmental Geology
• /
• v.23 no.4
• /
• pp.411-424
• /
• 1990

Mechanical, physical and petrographic properties of seventeen marble specimens collected from ten marble mines in Korea were investigated. Studied marbles were mainly composed of calcite, dolomite, and various amounts of serpentine, tremolite, olivine, quartz and opaque minerals. Complete and sutured textures were dominant. Compressive strength measured normal to the bedding plane is larger almost two times than that measured parallel to the bedding plane. From the results of Shore hardness test on marbles, water content was an important factor to decrease Shore hardness values. Engineering geological properties, especially, compressive strength, Young's modulus, wear resistance and water absorption could be controlled by the presence of quartz, and the type of marble texture. Water absorption-porosity, compressive strength-Young's modulus, and impact strength index-Los Angeles abrasion couples show good correlation. According to the comparative utility as commercial stone, it could be concluded that marbles from the Banglim mine, Songbo mine, Kwangdeok mine and Bongjeong mine were superior to that of other studied marbles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.6C
• /
• pp.275-284
• /
• 2012

The Antarctic continent exposed to strong wind, very low temperature, and extremely dry condition. The freezing-thawing cycles under this extreme environment change the mechanical characteristics of rocks near the ground surface. To investigate the effect of freezing-thawing cycles under the extreme environment understand on geotechnical properties of rocks, rocks from the Antarctica were collected from two places: (1) West Antarctic Cape Burks and (2) East Antarctic Terra Nova Bay areas. The rock characteristics of these two areas were described and compared. For Terra Nova Bay area, rock characteristics of rocks near the surface and depths exceeding 2.9 m were examined. The 'near-the-surface rocks' averages of absorption rate, P-wave velocity, and unconfined compressive strength were 0.56%, 3,717 m/s, and 109MPa, respectively; while, those values of 'deep-sited rocks' were 0.24%, 4,670 m/s, and 88MPa. From the measurements, it was found that the effects of weathering were not significant on mechanical characteristics (strength) but were pronounced on physical characteristics(absorption and P-wave velocity).

• Journal of the Korean GEO-environmental Society
• /
• v.2 no.4
• /
• pp.63-72
• /
• 2001

As construction cases on soft ground are increasing, the necessity of ground improvement is also increasing. Granular pile is one of the methods for soft clay and for loose sandy soil. In our country, SCP(Sand Compaction Pile) method using sand material has been mainly used to improve soft ground, but Granular pile with crushed-stone was not used much. However, alternative material such that crushed-stone is needed to substitute for sand due to the environmental and economical problems. In this study, staged load test and consolidation test were performed in the laboratory to observe the behavior of soft ground improved by Granular pile. In order to evaluate the characteristics such as bearing capacity, drainage, and settlement, sand and crushed-stone were applied as each pile material. The test results show that crushed-stone has higher bearing capacity and less settlement than those of sand under similar pore water pressure condition. Therefore, crushed-stone is determined to be appropriate as substitute for sand.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.6
• /
• pp.506-515
• /
• 2020

Surfing is a sport sensitive to changes in the natural environment, using naturally occurring waves. In other words, factors such as the construction of coastal structures, coastal erosion, and sediment transportation could cause the wave to change into a direction inappropriate for surfing at the shore where surfable waves were reaching. In this study, we call the characteristics of the coastal environment that affect the formation of surfable waves as surfing resources, which is subsequently analyzed by coastal engineering methodologies. Also, using Delft3D-WAVE module (SWAN model), a way to evaluate sustainability of surfable wave is suggested through analysis of surfing resources at Jukdo, Yangyang, Gangwon Province, Republic of Korea.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.5 no.1
• /
• pp.3-10
• /
• 2002

Quantifying the settling velocities of fine-cohesive sediments is very essential in the study of ocean pollutions as well as sedimentations. Settling properties of fine-cohesive sediments are influenced largely by aggregation which occurs as a consequence of interparticle collision and cohesion of particles. Since the degree of cohesion of fine-cohesive sediments depends on physico-chemical properties such as grain size distribution, percentage of organic materials, and mineralogical compositions, and these physico-chemical properties varies regionally, the settling velocities of fine-cohesive sediments for a specific site should be determined through field or laboratory experiment. Recently, settling velocities of fine-cohesive sediments in Saemankeum coasts and Kunsan Estuary have been measured through laboratory experiments. Using these data, the previously proposed well-known settling velocity equations for fine-cohesive sediments are examined and a new equation is developed for better representation of the measured data in this study. The newly developed settling velocity equation is simpler in the form and easier in determining the related coefficients than the previous well-known equations.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.4
• /
• pp.5-12
• /
• 2005

In this study, the geotechnical applicability of permeable barriers that could filter the leachate from a landfill was evaluated. Specimens were cast from sand, loess and bentonite according to the specific weight ratios of them. A series of experiments are performed to determine the unconfined compressive strength and permeability of various mixing ratio of bentonite, loess, and sand. From the laboratory test, optimum mixing ratio that satisfied the regulations of unconfined compressive strength($5kgf/cm^2$) and coefficient of permeability ($10^{-3}{\sim}10^{-4}cm/sec$) in landfill was found when the weight ratio of sand and loess was 8:2 with 2% of bentonite. Using the laboratory test data and in situ test results, the applicability of the wall will be tested for various conditions.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.6
• /
• pp.33-41
• /
• 2016

This study attempted to investigate drain capacity and vegetation potential of made-planting soil via finite element simulations. Engineering drain capacity of made-planting soil can be evaluated by an analysis of unsaturated soils. In a perspective for vegetation landscape, it is necessary to check whether the minimum amount of water in the made-planting soil can be supplied for the survival of plants. Herein, 1-m high soil column covered by made-planting soil were numerically simulated. Numerical results showed that how the coefficient of permeability of saturated soil and soil-water characteristics of unsaturated soil are considered significantly influences the drain capacity of soils. Variation in the volumetric water content within the Least Limiting Water Range (LLWR) provides us with information on whether the soil can contain a sufficient amount of water for the plants to survive the drought.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.3
• /
• pp.29-34
• /
• 2008

A large diameter sampler was developed to take undisturbed samples from not only soft ground but also sandy and weathered ground. The large diameter sampler which was developed in Korea Institute of Construction Technology(KICT-type large diameter sampler) was manufactured based on the principle of triple core barrel sampling. A specially designed cutting device was used to cut and contain various kinds of samples in the sampler during a sampling and retrieval procedure. By adjusting the stiffness of the spring located at the top of the sampler, the distance between the cutting shoe and auger can be controlled in accordance with the ground condition. In order to investigate the applicability of the developed sampler and compare the quality of the samples taken by the sampler with that by the traditional thin-walled tube sampler, samples were taken at various sites according to the ground condition. And a series of laboratory tests such as the unconfined compress ion test, triaxial compression test, oedometer test, large diameter Rowe cell consolidation test (D: 150 mm) were performed. The test results showed that the samples by the KICT-type large diameter sampler show higher quality than the samples by the thin-walled tube sampler. And the validity and applicability of the developed KICT-type large diameter sampler was confirmed accordingly.

• Journal of the Korean GEO-environmental Society
• /
• v.25 no.7
• /
• pp.21-27
• /
• 2024

Frost heave, a significant engineering aspect of frozen ground, leads to various damages in Korea during the winter. Both the United States and Japan, encompassing regions with frozen ground, have actively researched frost heave and possess standardized experimental methods. Particularly, the Japanese Geotechnical Society (JGS) has introduced a frost heave standard testing method, offering the advantage of relatively simple specimen preparation and experimental procedures. However, issues persist regarding the ambiguous engineering interpretation of frost heave test results and the lack of clear criteria for frost heave susceptibility assessment. This paper presents laboratory testing results following the JGS testing method on sand and silt mixtures using a triaxial temperature-controllable cell, and thoroughly analyzes the frost heave rate calculation process. Furthermore, it evaluates the applicability of frost heave susceptibility criteria proposed in the United States to frost heave rates based on the JGS testing method.

• Economic and Environmental Geology
• /
• v.41 no.6
• /
• pp.763-771
• /
• 2008

Uncertainties are pervasive in engineering geological problems. Therefore, the presence of uncertainties and their significance in analysis and design of slopes have been recognized. Since the uncertainties cannot be taken into account by the conventional deterministic approaches in slope stability analysis, the probabilistic analysis has been considered as the primary tool for representing uncertainties in mathematical models. However, some uncertainties are caused by incomplete information due to lack of information, and those uncertainties cannot be handled appropriately by the probabilistic approach. For those uncertainties, the theory of fuzzy sets is more appropriate. Therefore, in this study, fuzzy reliability analysis has been proposed in order to deal with the uncertainties which cannot be quantified in the probabilistic analysis due to the limited information. For the practical example, a slope is selected in this study and both the probabilistic analysis and the fuzzy reliability analysis have been carried out for planar failure. In the fuzzy reliability analysis, the dip angle and internal friction angle of discontinuity are considered as triangular fuzzy numbers since the random properties of the variables cannot be obtained completely under the conditions of limited information. In the study, the fuzzy reliability index and the probabilities of failure are evaluated from fuzzy arithmetic and compared to those from the probabilistic approach using Monte Carlo simulation and point estimate method. The analysis results show that the fuzzy reliability analysis is more appropriate for the condition that the uncertainties arise due to incomplete information.