• Journal of the Korean Electrochemical Society
• /
• v.4 no.4
• /
• pp.152-159
• /
• 2001

Electric vehicle performance is very dependent on traction batteries. For developing the electric vehicles with high performance and good reliability, the traction batteries have to be managed to get maximum performance under various operating conditions. The enhancement of the battery performance can be accomplished by implementing battery management system (BMS) that plays important roles of optimizing the control mechanism of charge and discharge of the batteries as well as monitoring battery status. In this study the battery management system has been developed for maximizing the use of Ni/MH batteries in electric vehicle. This system provides several tasks: the control of charging and discharging, overcharge and over-discharge protection, the calculation and display of state of charge, safety and thermal management. The BMS was installed in and tested using the DEV5-5 electric vehicle developed by Daewoo Motor Co. and Institute for Advanced Engineering in Korea. The 18 modules of Panasonic Ni/MH battery, 12 V-95 Ah, were used in the DEV5-5. The high accuracy within the range of $3\%$ and the good reliability were shown in the test results. The BMS can also improve the performance and cycle life of Ni/MH battery pack as well as the reliability and safety of the electric vehicles (EV).

• Proceedings of the Korean Quaternary Association Conference
• /
• 2004.06a
• /
• pp.46-46
• /
• 2004

Van Mijenfjorden은 스발바드 군도의 Spitsbergen 서부에 위치하는 두 번째로 큰 피오르드로 온난하고 염분도가 높은 북대서양의 표층수가 북극해로 유입되는 Gateway에 위치하기 때문에 전지구적이며 지역적인 기후변화의 영향을 받는 지역이다. 1999년 IMAGES 프로그램의 일환으로 프랑스 탐사선인 'R/V Marion Dufresne'을 이용하여 북극해의 스발바드 군도에 위치하는 Van Mijenfjorden (77$^{\circ}$ 46.87'N and 15$^{\circ}$ 17.81'E)에서 약 18m의 빙ㆍ해양 퇴적물 코아(MD99-2305)를 시추하여 마지막 최대 빙하기 이후의 고환경변화를 연구하였다. AMS 14C 연대 측정에 의하면 diamicton 층인 하부 2m를 제외한 16m의 퇴적층은 지난 12cal. ka BP경에 피오르드에 존재하던 조수빙하(tidewater glacier)가 해빙되기 시작한 이후에 퇴적되었다. 특히 유기지화학 자료와 부유성과 저서성 유공충의 산출양상 그리고 저서성 유공충인 C. reniforme의 산소ㆍ탄소 안정동위원소 비에 의하면 코아 MD99-2305에는 Van Mijenfjorden에서 홀로세 동안에 일어난 퇴적환경변화를 잘 기록하고 있다. 특히 홀로세 동안에 피오르드내의 퇴적환경 변화는 조수빙하의 확장과 후퇴와 밀접한 관계가 있으며, 유기물의 탄소동위원소(13Corg) 비는 -24에서 -22$\textperthousand$ 값의 변화를 보인다. 이는 Van Mijenfjorden 퇴적물에 공급된 유기물은 육상과 해양기원이 혼합되어 퇴적되었음을 지시한다. 지난 12 cal. ka BP 이후 13Corg 값이 뚜렷하게 변하는 것은 Van Mijenfiorden에서 조수빙하의 변동과 표층수에서의 생산력의 변화를 강하게 반영한다. 강하게 반영한다.53%가 이공계 출신, 100대 기업 CEO의 38.4%가 이공계 출신, 대입수능시험에서 자연계 지원비율이 감소 -40.1%('99)\$\longrightarrow$34.7%('00)\$\longrightarrow$29.4%('01)\$\longrightarrow$26.9%('02)\$\longrightarrow$30.3%('03)\$\longrightarrow$31.5%\$\longrightarrow$'04)필요성, 효과적인 운전자 교육 정책 등이 그것이다. 자동차 긴급 피난 차선은 유용한 시설로 여러곳에서 그 기능이 발휘되고 있으므로 많은 고속도로 관계자들은 설계, 시공 및 유지 관리 측면에서 유의해야 할 것이다.미세조직을 광학현미경으로 압출방향에 평행한 방향과 수직방향으로 관찰하였고, 열간 압출재 이방성을 검토하기 위하여 X선 회절분석을 실실하여 결정방위를 확인하였다. 전기 비저항 및 Seebeck 계수 측정을 위하여 각각 2$\times$2$\times$10$mm^3$ 그리고 5$\times$5$\times$10TEX>$mm^3$ 크기의 시편을 준비하였다.준비하였다.전류를 구성하는 주요 입자의 에너지 영역(75~l13keV)에서 가장 높은(0.80) 상관계수를 기록했다. 넷째, 회복기 중에 일어나는 입자들의 유입은 자기폭풍의 지속시간을 연장시키는 경향을 보이며 큰 자기폭풍일수록 현저했다. 주상에서 관측된 이러한 특성은 서브스톰 확장기 활동이 자기폭풍의 발달과 밀접한 관계가 있음을 시사한다.se that were all low in two aspects, named "the Nonsignificant group". And the issues were

• Journal of the Korean Electrochemical Society
• /
• v.8 no.4
• /
• pp.162-167
• /
• 2005

Using Pechini method, we synthesized the $La_{0.6}Ca_{0.41}CrO_3$ (LCC41) and $La_{0.8}Sr_{0.05}Ca_{0.15}CrO_3$ (LSCC) powders for slurry dip coating, and $La_{0.75}Ca_{0.27}CrO_3$ (LCC27) powder for air plasma spray coating. The sintering property of the powders and their coating properties were investigated. The average particle sizes of the LCC41, LSCC, LCC27 were 0.6, 0.9, $1.5{\mu}m$, respectively. The relative density of LCC41 bulk was to be found about 98%. The LSCC coating on anode support prevented Ca migration of the coated LCC41 on the anode some or less, which was confirmed from EDS result. The air plasma spray-coated LCC27 with the dip-coated LCC41 were more dense and showed better electrical conductivity than those of the air plasma spray-coated LCC27 and the dip-coated LSCC and LSCC41. The LCC41 and LCC27 showed good electrical conductivities, but the LSCC had a poor electrical conductivity probably due to low sinterability

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.1
• /
• pp.31-38
• /
• 2006

There are two types of metal hydride electrodes as a negative electrode in a Ni-MH battery, $AB_2$ Zr-based Laves phases and $AB_5$ LM(La-rich mischmetal)-based alloys. The $AB_5$ alloy electrodes have characteristic properties such as a large discharge capacity per volume, easiness in activation, long cycle life and a low cost of alloy. However they have a relatively small discharge capacity per weight. The $AB_2$alloy electrodes have a much higher discharge capacity per weight than $AB_5$ alloy electrodes, however they have some disadvantages of poor activation behavior and cycle life. Therefore, in order to improve the discharge capacity of the $AB_5$ alloy electrode the Zr, Ti and V which are the alloying elements of the $AB_2$ alloys were added to the $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}$ alloy which was chosen as a $AB_5$ alloy with a high capacity. The addition of Zr, Ti and V to $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}$ alloy improved the activation to be completed in two cycles. The discharge capacities of Zr 0.02, Ti 0.02 and V 0.1 alloys in $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V) were respectively 346, 348 and 366 mAh/g alloy. The alloy electrodes, Zr 0.02, Ti 0.05 and V 0.1 in $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V), have shown good cycle property after 200 cycles. The rate capability of the $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V) alloy electrodes were very good until 0.6 C rate and the alloys, Zr 0.02, Ti 0.05 and V 0.1, have shown the best result as 92 % at 2.4 C rate. The charge retention property of the $LaNi_{3.6}Ai_{0.4}Co_{0.7}Mn_{0.3}M_y$ (M = Zr, Ti, V) alloys was not good and the alloys with M content from 0.02 to 0.05 showed better charge retention properties.

• Applied Chemistry for Engineering
• /
• v.5 no.5
• /
• pp.764-771
• /
• 1994

Electrochemical synthesis of conductive polypyrrole films was carried out in nucleophilic solvent containing p-toluenesulfonic acid or bezensulfonic acid as supporting electrolyte and dopant. Also characteristics of degradation and improvement of mechanical properties were studied. The conductivity, tensile strength and elongation of the films obtained in dimethyformamide/p-toluenesulfonic acid had the highest value of 10-40S/cm, $25N/mm^2$ and 10%, respectively. The optimum condition of electrochemical synthesis was $2mA/cm^2$ for constant current method and 0.9V for constant potential method containing 0.5M pyrrole and 0.5M p-TSA. The obtained films showed good stability in air and electrode characteristics of secondary battery by reversibility in doping and undoping. The degradation process was 1st order reaction at various temeprature. The activation energy and rate constant of degradation reaction were $1.01JK^{-1}mol^{-1}$ and $3.1{\times}10^{-7}min^{-1}$ respectively at $25^{\circ}C$. For the improvement of mechanical properties, composition of polypyrrole films with various host polymer were investigated and increase of tensile strength and elongation was confirmed.

• Korean Journal of Materials Research
• /
• v.9 no.1
• /
• pp.14-17
• /
• 1999

Tin oxide films as an anode layer for microbatteries were deposited by using rf magnetron sputtering. Characterization of the films was carried out in terms of working pressure in the range of 5~30 mtorr. Rf power and substrate temperature during deposition were fixed at 2.5W/$\textrm{cm}^2$ and A.T., respectively. The crystal orientation of $SnO_2$films was changed from (110) to (101) or (211) with the increasing working pressure. Refractive index and film density of the films also decreased with the increasing working pressure. The $SnO_2$ thin film formed under optimum conditions was found to have a reversible capacity of 446.9$\mu$Ah/$\textrm{cm}^2$-$\mu\textrm{m}$ and good reversibility when the working pressure was fixed at 10mtorr. As the working pressure decreased, film density increased. It was thought that the capacity of $SnO_2$films increased due to the increase in the amount of active materials which can react with Li electrochemically. Furthermore, cycle characteristics of the anode material was also influenced by film stress.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.89-94
• /
• 2008

We synthesized and investigated $(La_{0.75}Sr_{0.25})_{1-x}FeO_{3-\delta}$ perovskite oxides having different stoichiomety (x = 0, 0.02, 0.04, 0.06, 0.08) as cathode materials. SEM images and XRD patterns reveal that the synthesized powder has uniform size distribution and high degree of crystallinity. The electrochemical performances of the synthesized powders were investigated by AC impedance spectroscopy. Both the electric conductivity and the electrochemical performance showed the highest properties at the stoichiometry x = 0.02. Finally, we concluded that the variation of A-site deficiency results in the variation of the amount of oxygen vacancy and micro structure, which leads to the variation of electric conductivity and polarization resistance.

• Analytical Science and Technology
• /
• v.7 no.3
• /
• pp.315-320
• /
• 1994

Li-GICs as a high performance energy storager were synthesized as a function of the Li content by the admixture and add-pressure method. The characteristics of these prepared compounds have been determined from the studies by X-ray diffraction, UV-VIS spectrometry and CHN analysis. It follows from the results of X-ray diffraction that the lower-stage intercalation compounds are formed as the Li contents increase, however the mixed stages in these compounds are also observed. In the case of the $Li_{40wt%}$, the compound with the structure of stage 1 has been predominently, but the structure of only stage 1 is not obtained. The $d_{001}$ value of stage 1 was determined to be ca. $3.70{\AA}$. An analysis of spectrometric data shows that each of the compounds gives distingushible energy state spectra. It is seen from the spectra that the positions of $R_{min}$ values, with increase in the Li contents, are shifted in the region of higher energy state. Such a result can be attributed to the formation of stable stages. The results of CHN analysis allow us to find the mixing state related to chemical compositions of the intercalated compounds and the superiority to admixture and add-pressure method. From the results determined, it reveals that $Li_{10wt%}$-GIC and $Li_{20wt%}$-GIC can be utilized for an anode of rechargable battery.

• Journal of Biomedical Engineering Research
• /
• v.39 no.5
• /
• pp.220-228
• /
• 2018

The internal resistance of microbial fuel cell (MFC) using stainless steel skein for oxidizing electrode was investigated and the factors affecting the voltage generation were identified. We also investigated the effect of power management system (PMS) on the usability for MFC and the removal efficiency of organic pollutants. The performance of a stack microbial fuel cell connected with (PMS) or PMS+LED was analyzed by the voltage generation and organic matter reduction. The maximum power density of the unit cells was found to be $5.82W/m^3$ at $200{\Omega}$. The maximum current density was $47.53A/m^3$ without power overshoot even under $1{\Omega}$. The ohmic resistance ($R_s$) and the charge transfer resistance ($R_{ct}$) of the oxidation electrode using stainless steel skein electrode, were $0.56{\Omega}$ and $0.02{\Omega}$, respectively. However, the sum of internal resistance for reduction electrode using graphite felts loaded Pt/C catalyst was $6.64{\Omega}$. Also, in order to understand the internal resistance, the current interruption method was used by changing the external resistance as $50{\Omega}$, $300{\Omega}$, $5k{\Omega}$. It has been shown that the ohm resistance ($R_s$) decreased with the external resistance. In the case of a series-connected microbial fuel cell, the reversal phenomenon occurred even though two cells having the similar performance. However, the output of the PMS constantly remained for 20 hours even when voltage reversal occurred. Also the removal ability of organic pollutants (SCOD) was not reduced. As a result of this study, it was found that buffering effect for a certain period of time when the voltage reversal occurred during the operation of the microbial fuel cell did not have a serious effect on the energy loss or the operation of the microbial fuel cell.

• Korean Chemical Engineering Research
• /
• v.58 no.3
• /
• pp.369-380
• /
• 2020

Most mono-crystalline silicon ingots are manufactured by the Czochralski (Cz) process. But If there are oxygen impurities, These Si-ingot tends to show low-efficiency when it is processed to be solar cell substrate. For making single-crystal Si- ingot, We need Czochralski (Cz) process which melts molten Si and then crystallizing it with seed of single-crystal Si. For melts poly Si-chunk and forming of single-crystalline Si-ingot, the heat transfer plays a main role in the structure of Cz-process. In this study to obtain high-quality Si ingot, the Cz-process was modified with the process design. The crystal growth simulation was employed with pulling rate and rotation speed optimization. Studies for modified Cz-process and the corresponding results have been discussed. The results revealed that using crystal growth simulation, we optimized the oxygen concentration of single crystal silicon by the optimal design of the pulling rate, rotation speed and melt charge level of Cz-process.