• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1556-1571
• /
• 1993

Nitrogen oxides ($NO_x$) are air pollutants which are generated from the combustion of fossil fuels. Stage combustion is an effective method to reduce $NO_x$ emissions. The effects of $NO_x$ reduction by stage combustion in a pilot scale combustor(6.6kW) have been investigated using propane gas flames laden with NH$_{3}$ as Fuel-N. The results in this study are follows; (1) $NO_x$ emissions are dependent on the reducing environment of fuel-rich zone regardless of total air ratio. The maximum $NO_x$ reduction is at the stoichiometric ratio of 0.8 to 0.9 in the reducing zone. (2) $NO_x$ reduction is maximum when burnout air is injected at the point where the oxygen in reducing zone is almost consumed. (3) $NO_x$ reduction is dependent upon the temperature of reducing zone with best effect above 950.deg. C in the reducing zone. (4) The fuel stage combustion is more effective to reduce $NO_x$ formation in the wide range of stoichiometric ratio than two stage combustion. (5) The results of this study could be utilized mainly in a design strategy for low $NO_x$ emission from the combustion of high fuel-nitrogen in energy sources ratio than as an indication of the absolute levels of $NO_x$ which can be achieved by stage combustion techniques in large scale facilities.

• Korean Journal of Materials Research
• /
• v.7 no.1
• /
• pp.33-39
• /
• 1997

Single phase pero~~skite lead lanthanum titanate thin films were fabricated on $Pt/Ti/SiO_2/Si$ substrates at the temperature of $480^{\circ}C$ by electron cyclotron resonance plasma-enhanced chemical vapor deposition (ECR PECVD) using metal organic sources $Pb(DPM)_2$ pre-flowing treatment in ECIi oxygen plasma before fabricating PLT films 11romote the perovskite nucleation due to stable supplying of the $Pb(DPM)_2$ and providing the F'h-rich atmosphere in the early stage of deposition. $Pb(DPM)_2$ pie-flonring treatment enhanced the properties of PLT films. The charactcristics of the PLT filrris were investigated as a tunction of the flow rate of Ti-source. The PL'i' films were grown in a perovskite structure tvith (100) preferred orientation. The high X-ray diffraction intensity and dielectric constant were obtained from the stoichiometric perovskite $(Pb,La)TiO_3$.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.239-246
• /
• 1993

The structure of $(BaSr)TiO_3$ thin film deposited on ITO coated glass, bare glass and (100) Si substrates was not changed, but the crystallinity was improved by the polycrystalline ITO layer and (100) Si substrate. The composition of $(BaSr)TiO_3$ thin film deposited on ITO coated glass was nearly stoichiometric ((Ba+Sr)/Ti=1.08~1.09) and very uniform through all deposition process. But as the deposition temperature increases, the interdiffusion between grown thin film and ITO layer and between ITO layer and base glass is severer. $(BaSr)TiO_3$ thin film deposited on ITO coated glass substrate was highly transparent. The refractive index($n_f$) of $(BaSr)TiO_3$ thin film deposited on ITO coated glass was 2.138~2.286 as a function of substrate temperature.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.512-518
• /
• 2008

The present work studied the selective catalytic reduction (SCR) of NO to $N_2$ by $NH_3$ over $V/TiO_2$ focusing on NOx control for the stationary sources. The SCR process depends mainly on the catalyst performance. The reaction characteristics of SCR with $V/TiO_2$ catalysts were closely examined at low and high temperature. In addition, adsorption and desorption characteristics of the reactants on the catalyst surface were investigated with ammonia. Seven different $TiO_2$ supports containing the same loading of vanadia were packed in a fixed bed reactor respectively. The interaction between $TiO_2$ and vanadia would form various non-stoichiometric vanadium oxides, and showed different reaction activities. There were optimum calcination temperatures for each samples, indicating different reactivity. It was finally found from the $NH_3-TPD$ test that the SCR activity was nothing to do with $NH_3$ adsorption amount.

• Fire Science and Engineering
• /
• v.19 no.3 s.59
• /
• pp.70-75
• /
• 2005

The heat of combustion of polymer materials is an important fire characteristics, which can be used with other fire parameter to predict the potential fire hazard in the polymer handling process. The aim of this study is to predict the heat of combustion for polymers which used in the building interior materials. By using the literature data and multiple regression, the new equation for predicting the heat of combustion of polymers is proposed. The A.A.p.E.(average absolute percent error) and the A.A.D.(average absolute deviation) of the reported and the calculated heat of combustion by means of the oxygen consumption calorimeter and the stoichiometric coefficient were 4.46 and 1.09, and the correlation coefficient was 0.972. The values calculated by the proposed equations were in good agreement with the literature data. Therefore, it is expected that this proposed equations will support the use of the research for other polymer materials.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.1
• /
• pp.46-49
• /
• 1999

Lithium cobalt oxide cathode for thin-film rechargeable lithium batteries were fablicated by electron-beam evaporation. Annealed lithium cobalt oxide, which was deposited on to stainless steel substrate, showed well-developed (003) planes of the hexagonal structure and potential plateau at $\~3.9 V$. Lithium cobalt oxide thin films had the stoichiometric Li/co ratio at high deposition rates and exhibited high discharge capacity at $15{\AA}/s$. As the annealing temperature increased, discharge capacity increased with maximum value at $700^{\circ}C$, but showed low capacity as a result of reaction with substrate above $700^{\circ}C$. Unuiformity of the lithium and cobalt in the depth profile gave initial capacity loss with charge/discharge performance.

• The Journal of Engineering Research
• /
• v.2 no.1
• /
• pp.133-138
• /
• 1997

The conventional process in synthesizing mullite powder required high temperature ($1300^{\circ}C$) and long chemical reaction time. Thus the combustion process was used to synthesize the mullite powder in order to reduce the reaction time and temperature. The mixture of metal nitrate, fine silica, and fuel was used as the redox compounds under various experimental conditions. The combustion fire in hot plate experiment in rich, lean and stoichiometry fuel does not produce mullite. However, the obvious mullite, small amount of alumina and cristobalite was observed in the $500^{\circ}C$ pre-heat treatment furnace experiment. The components such as silica, urea, aluminm nitrate should be stoichiometry in order to make a perfect mullite crystal.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1152-1157
• /
• 1998

The PZT films were deposited on the Pt/Ti/$SiO_2$/Si substrates using multi- target DC magnetron reactive sputtering. The perovskite single phase with the composition close to the stoichiometric one, was obtained even at high substrate temperature of $540^{\circ}C$ by 2-step method, which is that PZT film was deposited for a short time at low substrate temperature ($480^{\circ}C$) to promote the nucleation of perovskite phase by reducing the volatility of Pb oxide molecules, followed by the deposition at the elevated temperature to suppress the excess incorporation of Pb component in the PZT film. This two-step method, in combination with the RTA treatment, gives rise to good electrical properties of the deposited PZT films: remanent polarifaion,$18\mu$C/$\textrm{cm}^2$; coercive field, 45kV/cm; leakage current of 10$^{-4}$ A/$\textrm{cm}^2$ at high electric field of -500kV/cm.

• Journal of the Korean Vacuum Society
• /
• v.5 no.4
• /
• pp.348-353
• /
• 1996

Rapid thermal annealing (RTA) was applied to polycrystalline CdTe thin films evaporated on CdS/ITO/glass substrate and the effect of the annealing temperatures and the atmosphere on physical properties of polycrystalline CdTe thin films and CdTe/CdS solar cell characteristics were studied. Results obtained by EDX showed that the bulk composition of CdTe remained stoichiometric after annealing at $550^{\circ}C$ in the air but the surface composition became Cd-rich. Cross-sectional TEM and micro EDX showed that columnar grains and micro-twins remained even after RTA, however, and the sulfur content in the annealed CdTe (added by sulfur diffusion from CdS during the annealing) was much smaller than that by furnace annealing. Among the investigated RTA temperatures and gas environments, the cell made with CdTe annealed at $550^{\circ}C$ in air showed the best solar energy conversion efficiency.

• Korean Chemical Engineering Research
• /
• v.44 no.2
• /
• pp.121-128
• /
• 2006

Propylene epoxidation by $H_2O_2$ (30％ aqueous) as oxidant was studied in a semi-batch reactor using TS-1 catalyst: Effects of reaction temperature, time, pressure, solvent, catalyst and $H_2O_2$ concentration on $H_2O_2$ conversion (limiting reagent) and product distribution were investigated. Potential inhibition by propylene oxide on the epoxidation rate was also examined. Ti-MCM-22 with MWW zeolytic structure was found to exhibit better performance than TS-1 with MFI structure, provide that a proper choice of solvent(acetonitrile) is made.