• Journal of Animal Environmental Science
• /
• v.18 no.2
• /
• pp.99-110
• /
• 2012

The purpose of the study is to collect basis data for to establish standard administrative processes of liquid fertilizer treatment. From this survey we could make out the key point of each step through a case of effective liquid manure treatment system in pig house. It is divided into six step; 1. piggery slurry management step, 2. Solid-liquid separation step, 3. liquid fertilizer treatment (aeration) step, 4. liquid fertilizer treatment (microorganism, recirculation and internal return) step, 5. liquid fertilizer treatment (completion) step, 6. land application step. From now on, standardization process of liquid manure treatment technologies need to be develop based on the six steps process.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.6
• /
• pp.396-404
• /
• 2011

An investigation on the removals of PAH-quinone compounds, which are commonly produced from the biological and/or chemical treatments of PAH-contaminated soils, from the aqueous phase via birnessite (${\delta}-MnO_2$)-mediated oxidative transformation is described. It was demonstrated that acenaphthenequinone (APQ), p-PAH quinone can be removed via birnessite-mediated oxidative-coupling reactions, and anthraquinone (AQ) and 1,4-naphthoquinone (1,4-NPQ), o-PAH quinones were efficiently removed by birnessite-mediated cross-coupling reactions in the presence of catechol (CAT) as a reactive mediator. The removals of PAH-quinone compounds followed pseudo-first-order reactions, and the rate constant (k, $hr^{-1}$) for the removals of 1,4-NPQ under the experiment conditions (1,4-NPQ = 10 mg/L, CAT = 50 mg/L, ${\delta}-MnO_2$ = 1.0 g/L, pH 5, Reaction time = 6~96 hr) was 0.0426, which was about 4 times lower than that of APQ (0.173). With the observed pseudo-first order rate constants with respect to birnessite loadings under the same experimental conditions, the surface-normalized specific rate constant, $K_{surf}$, for 1,4-NPQ was determined to be $8.5{\times}10^{-4}L/m^2{\cdot}hr$. The analysis of the kinetic data with respect to birnessite loading indicated that the cross-coupling reactions of 1,4-NPQ consist of two different reaction steps over time and the results have also been discussed in terms of the reaction mechanisms.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.3
• /
• pp.164-176
• /
• 2012

In the present study, rapeseed flour (RSF), which is a by-product from the production of edible oil and biodiesel extracted from rapeseed, was used to develop alternative adhesives for the production of plywood panels. To examine the effects of the enzyme on the adhesive properties and formaldehyde emission of the RSF-based adhesive resins, three enzymes, such as cellulase (CEL), pectinase (PEC) and protease (ALC), were used either separately or together. As a crosslinking agent, PF prepolymers, which were prepared with 1.5, 1.8 and 2.1 mole formaldehyde and 1 mol phenol (1.8-, 2.1- and 2.4-PF), were added into the RSF hydrolyzates. The adhesive resins formulated with CEL- or CEL-PEC-RSF hydrolyzates and 1.8-F/P PF prepolymers exhibited excellent adhesive strengths and formaldehyde emission. The tensile shear strength and formaldehyde emission of the plywood panels bonded with the formulate resins were satisfied with the minimum requirement of the KS standard for ordinary plywood panels (0.6 N/$mm^2$). In addition, formaldehyde emissions of the plywood panels approached to that of E0 specified in the KS standard (0.5 mg/${\ell}$), and even had much better than those of commercial UF glue mixes. Overall, the use of RSF-based adhesive resins for the production of plywood panels might provide durable adhesive properties and an environmentally friendly substitute for petroleum-based adhesive resins. However, further researches - the increase of solid content of RSF-based adhesives for reducing press time and the microscopic observation of plywood specimen for identifying the relationship between tensile shear strength and the penetration of adhesives into wood structure - are required to commercialize the RSF-based adhesives.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.25-35
• /
• 2005

This study analyzed total concentrations and existing forms of heavy metals in soils of Ulsan using a sequential extraction method. Soil samples were collected from 6 categorized areas including green, residential, heavy traffic, petrochemical industrial complex(IC), mechanical and shipbuilding IC, and non-ferrous metal IC areas. which represent different emission characteristics. The highest total concentrations of heavy metals by a sequential extraction analysis were observed in the soils collected from the non-ferrous metal IC area, followed by the mechanical and shipbuilding IC and heavy traffic areas. Dominant(> 50%) existing forms of Cd, Cr and Ni were residual forms followed by Fe and Mn oxides in almost areas. Residual fractions in the non-ferrous metal IC areas were relatively lower than those in other areas. However, the fractions of organic and sulphides in the IC areas were higher. The dominant farms of Cu were much different with the investigated areas. In most areas, the dominant forms of Pb and Zn were Fe and Mn oxides, followed by residual fraction for Pb. The exchangeable and carbonate fractions represent mobility of metallic elements in soils. They are also significantly affected by the environmental renditions, such as pHs of soil and rainfall. In this study the exchangeable and carbonate fractions were lower than other fractions. Because the total concentrations of heavy metals in the soils of the non-ferrous metal IC area were extremely high, however, the mobile fractions of heavy metals in the IC area would be significant. Thus a large amount of heavy metals can be released into plants, water bodies, and soils. Therefore, urgent measures, such as source control for soil remediation of heavy metals, in the non-ferrous metal IC areas are essentially required. Analysis results obtained from the sequential extraction and the aqua regia extraction showed a high correlation, whose determination coefficients(R2) of heavy metals except Cd approximately ranged from 0.7 to 0.9.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.75-84
• /
• 2005

The aim of this study is to evaluate the leaching characteristics of lead, copper, cadmium, and mercury from steel making slag by seawater. To demonstrate the leaching characteristics of heavy metals from steel making slag by seawater, it was carried to various leaching tests such as regular leaching tests, liquid/sold(LS) leaching test and pH static test. From the leachability of $Pb^{+2},\;Cu^{+2},\;and\;Cd^{+2}$ from steel making slag in pH static test, it is distinguished between distilled water and seawater. With distilled water, it is very low between pH 7-8 and pH 11-12. On the other hands, with the seawater, its leaching is higher than that of distilled water. In particular, concentration of $Hg^{+2}$ leached from slag by seawater is lower than that of distilled water. Meanwhile, we found that the heavy metals from steel making slag would be dissolved and precipitated using geochemcial equilibrium program such as visual minteq. Lead and copper leached from steel making slag with seawater were dissolved nearly in the range of pH 11-12, but in the range of pH 7-10 those were precipitated about 90%. And cadmium leached from steel making slag with seawater were dissolved completely. On pH static test with distilled water, lead leached from steel making slag seemed to be similar to pH static test with seawater. However, copper and cadmium leached from steel making slag were dissolved. In general, the species of lead leached from steel making slag were formed mainly of $PbCl^+,\;PbSO_4$, the species of copper were formed mainly of $CuSO_4,\;CuCO_3$, the species of cadmium were formed mainly of $CdCl^+,\;CdSO_4$ due to being sorbed with the anions($Cl^-,\;CO_3^{-2},\;SO_4^{-2}$) of the seawater. Both pH static test with seawater and distilled water, it is not in the case of the mercury. Most of mercury leached from steel making slag was precipitated(SI=0). Because the decreasing of $Hg^{+2}$ concentrations depends ferociously on the variation of chloride($Cl^-$) existed in the seawater. $Hg^{+2}$ leached from steel making slag could be sorbed strongly with chloride($Cl^-$) compared of carbonate($CO_3^{-2}$) and sulfate($SO_4^{-2}$) in the seawater. On the basis of that result, we found that the species of mercury was formed of calomel($Hg_2Cl_2$) as one of finite solid. Due to forming a calomel($Hg_2Cl_2$) in the seawater, the stability of mercury species by steel making slag should be higher than those of lead, copper, and cadmium species. Regarding the results stated above, we postulated that the steel making slag could be recycled to sea aggregates due to being distinguishing leachability of heavy metals($Pb^{+2},\;Cu^{+2},\;Cd^{+2},\;and\;Hg^{+2}$) between leaching tests by distilled water and seawater.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.101-108
• /
• 2005

Because the stone cultural properties located outdoors, they have been altered and deteriorated in external appearance due to environmental factors such as acid rain, extreme change in temperature, and salts. Damage to stone cultural properties is accelerated particularly due to recent industrial development and environmental pollution. An experimental study was conducted to evaluate the effect of environmental contaminants on the weathering of granite. And as part of the developing of conservation method, $TiO_2$ catalyst was prepared and tested. When fresh granite was dipped into the salt and acid solutions, dissolution rate of eight minerals (Si, Mg, Ca, Na, K, Fe, Mn, Al) are abruptly increased at initial stage of reaction and then increased steadily until 100 cycles. After salt and acid solution experiments, the mineral compositions of the granite surface were lower then that of the fresh granite and density of the weathered granite was steadily decreased from $2.60\;g/cm^3$ to $2.56\;g/cm^3$, but Poissions ratio and absorption ratio were slightly increased. It was expected at stone cultural assets could be weathered by salts and acid rain. In the case of $TiO_2$ was coated to the granite, the dissolution rate of minerals and absorption ratio of $TiO_2$ coated granite were decreased. Therefore, the $TiO_2$ coating method tested in this study considered to be a viable method to assist in the conservation of stone cultural properties from environmental contaminants.

• Journal of environmental and Sanitary engineering
• /
• v.5 no.1
• /
• pp.7-13
• /
• 1990

The water environmental characters of the Nakdong River, Geumho River and Sin Stream, both before-flood (Aug. 24) and after-flood (Sept. 8), have been compared, and their effects on the growth of Spirodela polyrhiza Shleiden have been examined. Before the flood, the concentrations of most of the chemical components of the Geumho River were similar to those of the Sin Stream; (COD, 19.6~21.4; alkalinity, 177~183; $NH_4\;^+$, 20.7~24.4; $NO_3\;^-$, 3.9~4.3; $PO_\;4^{3-}$, 3.4~3.7; $Mg^{2+}$, 42; $Ca^{2+}$, 68.5~69.7; $Cl^-$, 90~92; $SiO_2$, 10.4~11.2; , 11~32; LAS, 3.0~3.8; , 0.007~0.010ppm) but much higher than those of the Nakdong River (30~40 fold for $NH_4\;^+$, , $PO_\;4^{3-}$ and LAS, and 2~5 fold for COD, alkalinity, $NO_3\;^-$, $Mg^{2+}$, Cl- and ). Especially in the Geumho River, Secchi disk transparency was very low (17cm) and DO was not detected. The flood caused significant increases in some chemical components: $NH_4\;^+$, 1.0;$NO_3\;^-$, 9.6; , 12.8 and , 5.4 ppm in the Nakdong River; DO, 1.0; $NO_2\;^-$, 0.92; $NO_3\;^-$, 22.2 and $SiO_2$, 17.6ppm in the Geumho River; DO, 3.0; $NO_2\;^-$, 1.4; $NO_3\;^-$, 22.2; SiO2$SiO_2$, 19.2 and , 25.0ppm in the Sin Stream. General species diversity index (H) of phytoplankton community in the Nakdong River, Geumho River and Sin Stream before flood was 3.1, 2.7 and 1.6, respectively. After the flood, the phytoplankton growth was highly sparse in each river water, hence indices have no significance. The growth of S. polyrhiza was enhanced in Geumho River water (max. RGR=26%/day), while it ceased within 7days in Nakdong River water.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.126-138
• /
• 2017

This study was conducted to investigate the potential of chicken feather (CF), which is a by-product in poultry industry, as a raw material of wood adhesives. For the purpose, adhesive resins were formulated with NaOH- and $H_2SO_4$-hydrolyzed CF as well as crosslinkers, and then the properties and water resistance of the adhesive resins against hot water were measured. CF was made of mainly keratin-type protein, and no or very low content of heavy metals was detected. Hydrolysis rate of CF increased as NaOH concentration in hydrolysis solutions increased. However, in order to minimize the loss of adhesive property of protein itself by the severe hydrolysis of CF and to seek its proper hydrolysis conditions, NaOH concentrations in hydrolysis solution determined to adjust to 5%, 7.5% and 10%. In the NaOH-hydrolyzed CF, $H_2SO_4$-hydrolyzed CF as a hardener and crosslinker were added to formulate CF-based adhesive resins. Solid content of the resins ranged from 28.3% to 44.8% depending on hydrolysis conditions and type of crosslinker. Viscosity of the resins at $25^{\circ}C$ was very high. However, when the temperature of the resins was increased to $50^{\circ}C$, the viscosity decreased greatly and thus the resins could be applied as a sprayable resin. Retention rate measured to evaluate the water resistance of adhesive resins was the highest in the cured resin formulated with 5% NaOH-hydrolyzed CF and 5% $H_2SO_4$-hydrolyzed CF of 10% based on the solid weight as a hardener. Retention rate depending on crosslinkers added into adhesive resins was the highest phenol-formaldehyde (PF) followed by melamine-urea-formaldehyde (MUF) and formalin. The retention rate of CF-based adhesives formulated with 5% NaOH-hydrolyzed CF, PF and $H_2SO_4$-hydrolyzed CF of 10% and over did not differ statistically from that of commercial MUF resins. All of CF-based adhesives formulated with PF as a crosslinker and one with 5% NaOH-hydrolyzed CF of 55%, 5% $H_2SO_4$-hydrolyzed CF of 15%, and MUF of 30% on the basis of solid weight could be substituted for commercial urea-formaldehyde resins, From the results, CF can be used as a raw material of wood adhesives if hydrolyzed in proper conditions.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.3
• /
• pp.258-267
• /
• 2017

In this study, pitch pine (Pinus rigida, PIR) and Mongolian oak (Quercus mongolica, QUM) pellets were fabricated with bark or/and drying waste liquor (DWL) of larch (Larix kaempferi, LAK) as an additive. Based on the results of fuel characteristics of the pellets, optimal conditions for producing the high-quality pellets were provided. In the analysis of chemical composition, bark contained holocelluose and lignin of 90% and over. DWL had 0.1% solid assumed to sugars which are generated from the oven-drying of LAK logs. QUM showed high ash content (2.2%) by containing of bark in the sawdust. Bark and DWL of LAK had high ash content of 4% and over. Calorific values of all specimens and additives were higher than that of the $1^{st}$-grade standard of wood pellets designated by NIFOS (18.0 MJ/kg). PIR and QUM pellets were fabricated with additive of 2 wt% based on the solid weight of oven-dried sawdust using a piston-type flat-die pelletizer, and thus ash content and calorific value of the pellets did not affect by the use of additive. Durability of the pellets increased with the use of additive. Durabilties of pellets, which were fabricated with bark as an additive and DWL as a controller of moisture content for sawdust, did not differ from those of pellets without additives and were lower than those of pellets either with bark or DWL. However, use of both bark and DWL for the production of wood pellets might be favorable because it can make a profit from the collection process of DWL. Based on the results of fuel characteristics of the pellets, QUM and PIR pellets were produced by a flat-die pelletizer. Moisture content (MC), bulk density and durability of the pellets improved with the use of additive. Particularly, sawdust MC of 10% and the addition of bark or DWL for PIR as well as sawdust MC of 12% and the addition of bark for QUM might be optimal conditions for the production of high-quality pellets. Except for the ash content of QUM pellets, other properties of PIR and QUM pellets exceeded the $1^{st}$-grade wood pellets standards of NIFOS.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.599-612
• /
• 2017

Human hair (HH) is produced as a waste from beauty parlor and barbershop. HH-based adhesives were formulated with NaOH-hydrolyzed HH, $H_2SO_4$-hydrolyzed chicken blood (CB) and PF as a crosslinking agent. Physicochemical properties and retention rate against hot water of the adhesives were measured to investigate the potential of HH as a raw material of wood adhesives. HH was composed of keratin-type protein of 80% and over. Ash of less than 0.1% was contained in HH. Among the amino acids included in HH, glutamic acid showed the highest content, followed by cysteine, serine, arginine and threonine. Solid content of the adhesives ranged from 33.2% to 41.8% depending on hydrolysis conditions of HH and PF type. Viscosity at $25^{\circ}C$ ranged from 300 to $600mPa{\cdot}s$ resulting in a sprayable adhesive. Retention rate against hot water measured to evaluate the water resistance of adhesives was the highest in the cured resin formulated with 5% NaOH-hydrolyzed HH and 5% $H_2SO_4$-hydrolyzed CB. Meanwhile, the molar ratio of formaldehyde to phenol in PF did not have a significant impact on the retention rate of HH-based adhesives. When the retention rates of HH-based adhesives were compared to those of conventional wood adhesive resins used for the production of wood-based panels extensively, HH-based adhesives formulated with 30 wt% PF showed lower retention rate than commercial urea-formaldehyde resin. However, when PF content was increased to 35 wt%, the retention rate greatly increased and approached to that of commercial melamine-urea-formaldehyde resin. Except for the results mentioned above, the analysis of economic feasibility suggests that HH-based adhesives can be used for the production of wood-based panels if HH is hydrolyzed in proper conditions and then the HH-based adhesives are formulated by the HH hydrolyzates with 35 wt% PF.