• Fire Science and Engineering
• /
• v.23 no.1
• /
• pp.55-62
• /
• 2009

A general combustion characteristics of forcing nonpremixed jet in laminar flow rates have been conducted experimentally to investigate the effect of forcing amplitude with the resonant frequency of fuel tube. There are two patterns of the flame lift-off feature according to the velocity increasing; one has the decreasing values of forcing amplitude on the lift-off occurrence when a fuel exit velocity is increasing, while the other has the increasing values. These mean that there are the different mechanisms in the lift-off stability of forced jet diffusion flame. Especially, the characteristics of attached jet flame regime are concentrically observed with flame lengths, shapes, flow response and velocity profiles at the nozzle exit as the central figure. The notable observations are that the flame enlogation, in-homing flame and the occurrence of a vortical motion turnabout have happened according to the increase of forcing amplitude. It is understood by the velocity measurements and visualization methods that these phenomena have been relevance to an entrainment of surrounding oxygen into the fuel nozzle as the negative part of the fluctuating velocity has begun at the inner part of the fuel nozzle.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.6
• /
• pp.11-18
• /
• 2014

The combustion flowfield at the near-injector region of a 50 N scale $N_2O/C_2H_5OH$ thruster was visualized using shadowgraph technique. The explosive ignition was occurred at the design spray condition, and the expanding combustion gas quenched the flame immediately. Approximately after 83 ms from the initial ignition, the propellant spray was re-ignited, and the flame was stabilized after 23 ms elapsed. In the increased oxidizer flow rate condition, the transient pressure at the moment of ignition was smoother than explosive ignition, and the blow down phenomenon was not appeared in the same operating sequence. In addition, the flame was stabilized within 17 ms, and it is caused by improved propellants mixing before ignition.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.57-64
• /
• 1999

Initial flame development and propagation were visualized under the new ignition system developed to estimate the effects of ignition characteristics on the engine performance in a port injection SI engine. Effects of intake air flow characteristics were also investigated by three different kinds of the swirl control valve. Experiments were performed in an optical single cylinder engine modified form a commercial engine. Flame images were captured through the quartz window mounted in the piston by the high speed video camera and analyzed to compare initial flame development. Results show that IMEP tends to rise slightly as the ignition duration gets longer. The direction of flame propagation is decisively governed by the in-cylinder flow motion. Every flame grows toward the exhaust valve forming a kind of turbulent flame. Initial flame propaagation characteristics are very similar to ones analyzed form pressure data.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1727-1736
• /
• 1991

본 연구에서는 자체 제작된 헬름홀쯔형 맥동 연소기를 이용하여 작동원리와 연소특성을 조사함으로써 맥동연소현상을 물리적으로 이해하는 것이다. 주기적 화염 의 직접가시화, 연소장의 시간평균 온도 및 농도분포, 변동압력의 크기와 공기흡입량 을 조사함으로써 맥동에 영향을 미치는 요인이 무엇인지 그리고 이것이 어떠한 변화를 야기시키는가를 살펴보고자 한다. 이렇게 얻어진 결과의 종합을 통해 장치의 형상이 결정된 일반적인 맥동연소기가 자발적인 상태에서 작동될 때 작동결정인자가 무엇인가 를 알수가 있을 것으로 사료된다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.60-69
• /
• 2003

The simplified two-color method is proposed which can estimate the temperature distribution and the soot density of the whole flame with the image analysis of the high-speed photographs. The factors influenced on its processing were examined, for example, the selection of the wave length, the kind of films, the preparation of the calibration curve between the radiance of flame and the luminance temperature. The simplified two-color method reported in this paper can be used as a tool for the improvement of the combustion process in direct injection diesel engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.54-64
• /
• 1995

The effects of swirl on early flame development and late combustion characteristic were investigated using a high speed single-shot visualized 51 engine. LDV measurements were performed to get better understanding of the flow field in this combustion chamber. Spark plugs were located at half radius (R/2) and central location of bore. High speed schlieren photographs at 20,000 frames/sec were taken to visualize the detailed formation and development of the flame kernel with cylinder pressure measurements. This study showed that high swirl gave favorable effects on combustion-related performances in terms of the maximum cylinder pressure and flame growth rate regardless of spark position. However, at R/2 ignition the low swirl shown desirable effects at low engine speed gave worse performances as engine speed increased than without swirl. There were distinct signs of slow-down in flame growth during the period when the flame front expanded from 2.5mm in radius until it reached 5.0mm apparently due to the presence of ground electrode. There seemed to be heat transfer effect on the flame expansion speed which was evidenced in high swirl case by the slowdown of the late flame front presumably caused by relatively large heat loss from burned gas to wall compared with low- or no-swirl cases.

• Journal of the Korean Society of Combustion
• /
• v.4 no.1
• /
• pp.49-57
• /
• 1999

An experimental study on double-concentric diffusion flame has been carried out in order to investigate the shape, the flame length, and the other characteristics of the flame. Flow visualization of the flame by the $TiO_2$ particles and also the emission measurements are conducted. The commercial grade LP gases are used as fuel. The inverse diffusion flames are formed at the center when the central air flow rate is about 0.1 L/min. With a larger flow rate of the central air jet than 0.2 L/min the flame turns to be an annular-shaped flame, which is very bright. When the central air flow rate increases over 2.4 L/min, the flame turns to blue and the flame tips are opened because of the lifting of the inner part of the flame. Because of this lifting and the incomplete combustion, the CO emission increases abruptly from 25 ppm to more than 150 ppm. On the contrary, the NOx emission is decreased.

• Journal of the Korean Society of Combustion
• /
• v.6 no.1
• /
• pp.1-6
• /
• 2001

To evaluate the effect of lobed structure on pollutant emission, an experimental study examines NOx and CO emissions associated with four burner geometries, such as a conventional circular burner and three lobed ones. Rapid mixing allowed by the lobed burner to produce lean premixed flames, with narrower flame stability diagram than for the conventional circular one. Conventional circular burner of wide and uniform burner rim has an advantage of flame stabilization. Correlation on fuel discharge velocity for flame blowout should be included a variable related to the wall effect of the burner. NOx emission reduces by about 5% at the burner with lobed structure in fuel discharge side compared to conventional circular one. This is due to lower flame temperatures through flame elongation and increased radiative heat losses, caused by partially luminous flame in flame front. Meanwhile, at the burner with lobed structure in air discharge side and both fuel and air discharge sides, NOx emission somewhat increases with reduced radiative heat losses in spite of flame elongation. Therefore, the rapid mixing by lobed structure does not always have an advantage on NOx reduction.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.430-432
• /
• 2011

An experimental study of the flame response in a turbulent premixed combustor has been conducted in order to investigate mechanisms for combustion instabilities in lean premixed gas turbine combustor. A lab-scale combustor and mixing section system were fabricated to measure the flame transfer function. Measurements are made of the velocity fluctuation in the nozzle using hot wire anemometry and of the heat release fluctuation in the combustor using chemiluminescence emission. The results are analyzed to determine the phase and gain of the flame transfer function as a function of the modulation frequency and operating conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.70-80
• /
• 2019

Combustion tests using six bi-swirl coaxial injectors with different shapes and recess lengths were performed in a model combustion chamber capable of flame visualization. By utilizing gaseous methane and gaseous oxygen instead of actual propellants, the effects of injector design and experimental conditions on the flame structure and combustion stability were analyzed. It was found that not only the experimental conditions but also the injector geometry such as the recess length and orifice diameter had a considerable influence on the combustion stability. In addition, it was confirmed that the heat release pattern changed with the occurrence of combustion instability.