• Explosives and Blasting
• /
• v.33 no.1
• /
• pp.13-20
• /
• 2015

Recently, as the demand for development and utilization of underground space is increasing worldwide, the blast damaged zone has become a major issue in constructing underground structures. In this study, numerical analyses were performed for modelling a small-scale blasting of rock plates using PFC3D and ANSYS LS-DYNA. In order to verify the analysis results, several test blasts were conducted. It is concluded from the study that the numerical modelling methods well simulate the crack propagation procedure near blast holes under given conditions.

• Explosives and Blasting
• /
• v.30 no.1
• /
• pp.1-8
• /
• 2012

In this study, the inner principal stress of concrete blocks caused by an impact load was analyzed with a finite element program, Visual FEA, which was used to model the cross section of the concrete blocks. As a result, it was found that the deviation of the maximum principal stress was varied 2 to 3 times depending on the physical properties of the concrete blocks.

• Explosives and Blasting
• /
• v.26 no.1
• /
• pp.7-14
• /
• 2008

In order to complete successfully the demolition of a silo structure by means of felling method, structural properties and the geometric design of blast mouth have to be considered. In this study, a commercial software, 3-dimensional applied element analysis (3D AEM), was used to investigate the effect of the geometrical parameters of blast mouth on the collapse behavior of the silo structure.

• Explosives and Blasting
• /
• v.35 no.4
• /
• pp.10-18
• /
• 2017

In this study, Rock deformation at the artificially advanced face was investigated by using the finite element code relating to the split blasting conducted in urban area. The maximum principal strain according to the detonation pattern and the detonation delay time at the rock surface was compared with the modeled blast section. As a result, it was found that the maximum principal strain was observed a difference depending on the detonation pattern at the rock surface, and the detonation delay time was an important parameter in split blasting.

• Proceedings of the KSEE Conference
• /
• 2006.10a
• /
• pp.55-66
• /
• 2006

일반적으로 현장에서의 발파공법의 적용은 보안물건과 발파지점의 거리로 구분하여 설계한 종례의 방법에서 탈피하여 건설교통부에서 보안시설건물의 거리${\sim}$지발당장약량을 기초로 한 6가지의 타입으로 표준화한 방법을 제시하였다. 이는 시험발파를 통하여 발파공해 허용 기준치를 확보하고 회귀분석을 통한 발파영향권을 분석한 후 이격거리별 발파패턴 및 발파공법을 선정 및 설계를 기본으로 하는 것이며 이번 00대학교 민석도서관 건립공사에서 적용하여 타당성을 검토하여 실제 설계 시 적용을 하였으며 6 가지 타입의 기초적인 모델링을 기본으로 하여 시공설계 및 계측결과를 분석하였다.

• Explosives and Blasting
• /
• v.38 no.3
• /
• pp.15-29
• /
• 2020

In this paper the Hoek-Brown (HB) failure criterion is integrated into the Holmquist-Johnson-Cook (HJC) concrete material model to reflect the inherent characteristics of field rock masses in LS-DYNA blast modeling. This is intended to emphasize the distinctive characteristics of field rock masses that usually have many geological discontinuities. The replacement is made only for the static strength part of the HJC material model by using a statistical curve fitting technique, and its procedure is described in detail. An example is also given to illustrate the use of the obtained HJC material model. Computation is performed for a plane strain model of a single-hole blasting on a field limestone by using the combination of the fluid-structure interaction (FSI) technique and the multi-material arbitrary Lagrangian Eulerian (MMALE) method in LS-DYNA.

• Explosives and Blasting
• /
• v.37 no.2
• /
• pp.14-21
• /
• 2019

Distinct element method is a powerful numerical tool for modelling the jointed rock masses. It is also a useful tool for modelling of later stage of blasting requiring large displacement. The distinct element method utilizes a rigid block idea in which the interacting force between distinct elements is calculated from contact displacement as elements penetrate slightly. The properties of joints defined as the boundaries of distinct elements are critical parameters to determine the block behavior, and affect the deformation and failure mode. However, regardless of real joint properties, joint stiffnesses have sometimes been selected without special concern just to prevent elements from penetrating too far into each other in some quasi-static problems. Depending on whether the main interest in the analysis is the prediction of the deformation with high precision, or the prediction of the block behaviour after failure, the input data such as joint stiffness may or may not have a significant effect on the results. The purpose of this study is to provide a sound understanding of the effect of the joint stiffness on the distinct element analysis results, and to help guide the selection of input data.

• The Journal of Engineering Geology
• /
• v.28 no.4
• /
• pp.701-714
• /
• 2018

The purpose of this study is to show the possibility of 3-dimensional modeling of open-pit limestone mine by using a rotary-wing unmanned aerial vehicle, a drone, and to estimate the amount of mining before and after mining of limestone by explosive blasting. Analysis of the image duplication of the mine has shown that it is possible to achieve high image quality. Analysis of each axis error at the shooting position after analyzing the distortions through camera calibration was shown the allowable range. As a result of estimating the amount of mining before and after explosive blasting, it was possible to estimate the amount of mining of a wide range quickly and accurately in a relatively short time. In conclusion, it is considered that the drone of a rotary-wing unmanned aerial vehicle can be usefully used for the monitoring of open-pit limestone mines and the estimation of the amount of mining. Furthermore, it is expected that this method will be utilized for periodic monitoring of construction sites and road slopes as well as open-pit mines in the future.

• Explosives and Blasting
• /
• v.39 no.3
• /
• pp.1-14
• /
• 2021

Rockburst is a sudden and violent failure of rock. During the failure process, excess energy is liberated as seismic energy, which in turn causes the surrounding rock mass to vibrate. The level of the ground vibration can reach a magnitude of over 4.5 in the Richter local scale. Thus, a rockburst can cause not only injury to persons, but also damage to both underground workings and surface structures. In this paper the source mechanism of rockburst is analyzed based mainly on the two reports of the Canadian Rockburst Research Program (CRRP). A simplified LS-DYNA modeling is also performed to identify the tensile failure patterns occurring in the remaining rock mass right after blasting in mine stope. The configuration of the simplified model will probably be useful in small-scale laboratory tests for investigating the source mechanism of rockburst.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.75-85
• /
• 2003

Laboratory model blast and in-situ rock blast tests were conducted to determine blast-induced stress wave propagation characteristics under different explosive types, different loading conditions and different mediums. Dynamic numerical approaches were conducted under the same conditions as experimental tests. Stress magnitudes at mid-point between two blast holes which were detonated simultaneously increased up to two times those of single hole detonation. The rise time of maximum stress in a decoupled charge condition was delayed two times that of a fully charged condition. Dynamic numerical analysis showed almost similar results to blast test results, which verifies the effectiveness of numerical approaches fur optimizing the tunnel blast design. Dynamic numerical analysis was executed to evaluate rock behavior and damage of the contour hole, the sloping hole adjacent to the contour hole in the road tunnel blasting pattern. The rock damage zone of the sloping hole from the numerical analysis was larger than that of the contour hole. Damage in the sloping hole can be reduced by using lower density explosive, by applying decoupled charge, or by increasing distance between the sloping hole and the contour hole.