• Journal of Ocean Engineering and Technology
• /
• v.12 no.2 s.28
• /
• pp.121-129
• /
• 1998

A quantitative non-contact multi-point measurement system is proposed to the measurement of three-dimensional movement of floating vessels by using digital image processing. The instantaneous three-dimensional movement of a floating structure which is floating in a small water tank is measured by this system and its three-dimensional movement is reconstructed by the measurement results. The validity of this system is verified by position identification for spatially distributed known positional values of basic landmarks set for the camera calibration. It is expected that this system is applicable to the non-contact measurement for an unsteady physical phenomenon especially for the measurement of three-dimensional movement of floating vessels in the laboratory model test.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.556-560
• /
• 1996

In order to examine thd accuracy of intersection counting method, the fiber orientation distribution of simulation figure platted by PC is measured using image processing. The fiber orientation distribution obtained by an image processing method is compared with those by the intersection counting method. The result shows that the errors of the intersection counting method are large because its measurement is made by the cross point of the scanning line and the fiber.

• Journal of ILASS-Korea
• /
• v.5 no.2
• /
• pp.68-74
• /
• 2000

A this experimental study is executed to analyze spray characteristics for air-shrouded injector and 4hole 2spray type injector used in a gasoline engine. Since spray parameters including spray penetration and angle, SMD, and atomization characteristics are very important to increase the engine performance, the image processing algorithm for measuring the non-spherical spray diameter is developed. Spray characteristics of the air-shrouded injector(2hole 2spray) and 4hole-2spray injector are analyzed respectively by this digital image processing method. Effective spray characteristics to injectors is derived from this experimentation and obtained the design guide for gasoline injector.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.6
• /
• pp.78-83
• /
• 1999

This study discusses a non-contact optical technique, electronic speckle pattern interformetry(ESPI), that is well suited for in-plane and out-of-plane deformation measurement. However, the existing ESPI methods that are based on dual-exposure, real-time and time-average method have difficulties for accurate measurement of structure, due to irregular intensity and shake of phase. Therefore, phase shifting method has been proposed in order to solve this problem. About the method, the path of reference light in interferometry is shifted and added to least square fitting method to make the improvement in distinction and precision. This proposed method is applied to measure in -plane displacement that is compared with the previous method. Also, Used as specimen AS4/PE따 [30/=30/90]s was analyzed by ESPI based on real-time to determine the characteristics of vibration under no-load and tension. These results are quantitatively compared with those of FEM analysis inmode shapes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.120-128
• /
• 1997

The variations of the temperature field in a passenger compartment were measured by using a HSI true color image processing system and TLC(Thermochromic Liquid Crystal) solution. This temperature measurement technique was proved to be useful for analyzing the ventilation flow. The flow field in the passenger compartment was visualized using a particle streak method with pulsed laser light sheet. The temperature field and flow field in the passenger copartment were affected significantly by the ventilation mode. The panel-vent mode heating had shorter elapse time to reach a uniform temperature than the foot-vent mode under the same ventilation condition and nonuniformity inside the passenger compartment could be minimized effectively by using the bilevel heating mode. The temperature increase rate in the rear passenger compartment was iower than the front compartment, especially in the vicinity of the rear seat occupants' knee level.

• Journal of ILASS-Korea
• /
• v.3 no.1
• /
• pp.1-9
• /
• 1998

Two measurement techniques of droplet sizing, an imaging technique(PMAS) and a phase-Doppler measurement technique (PDPA), have been compared using a water spray from a pressurized-type swirl nozzle. The result showed that SMD measured by PDPA was larger than that measured by PMAS by about 40 %. Such discrepancy of SMD could be explained by the fact that the light signal intensity used by PDPA can be biased towards larger particles. On the other hand there could be lower opportunity to capture the images of the large particles with PMAS, since the large particles could be out of sight due to their high speed.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2002.11b
• /
• pp.1277-1280
• /
• 2002

화상회의 시스템들은 여러 명의 사람들에게 멀티미디어 데이터를 공유하여 전송하기 때문에 안정적인 대역폭을 보장받지 못하며, 계속적으로 변화하는 네트워크 상태에서 최적의 서비스를 제공하기 위해서는 동적 흐름제어 기법이 필요하게 된다. 동적 흐름제어 기법은 최적의 서비스를 제공하기 위해서 사용 대역폭이 클 경우에는 데이터의 량이 많은 고품질의 데이터를, 사용 가능한 대역폭이 낮을 경우에는 데이터의 량이 적은 저품질의 데이터를 생성한다. 본 논문에서는 기존의 두 가지 흐름제어 기법에서 사용된 측정 요소인 패킷 손실율과 왕복 시간외의 성능을 개선시킬 수 있는 요소인 네트워크 상태에 따른 제어 메시지의 빈도수와 데이터의 량을 이용한 동적 흐름제어 기법을 제안한다. 또한 실험을 통하여 기존의 동적 흐름제어 기법과 제안한 동적 흐름제어기법의 성능을 비교하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.3
• /
• pp.1114-1122
• /
• 1996

Variation of temperature field in a Hele-Shaw convection cell was measured by using a HSI true color image processing system and TLC(Thermochromic Liquid Crystal) solution. The relationship between the hue value of TLC color image and real temperature was obtained and this calibration result was used to measure the true temperature. The temperature field in the Hele-Shaw convection cell shows periodic characteristics of 45 sec at Ra = 9.3 * 10$\^$6/. The temperature field measurement technique developed in this study was proved to be a useful and powerful tool for analyzing the unsteady thermal fluid flows.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2002.05a
• /
• pp.205-209
• /
• 2002

인체의 피부온도는 쾌적성과 감성에 크게 영향을 미치며 의류의 개발이나 건축환경의 설계 등에 활용되고 있다. 단순히 몇몇 측정점에서의 피부온도 데이터가 아니라 인체표면에 걸친 온도분포를 파악함으로써 다양한 정보를 이용하여 보다 광범위한 응용분야에 활용될 수 있을 것이다. 현재 인체표면의 온도분포를 측정하기 위하여 대부분 적외선 열화상 카메라를 활용하고 있다 그러나 열화상 카메라는 서미스터 등을 이용한 피부온 센서에 비하여 온도분해능이 떨어지며 특히 의복내의 피부온을 측정하는 것이 불가능하고 노출된 인체표면에 대해서만 측정이 가능하다. 따라서 본 연구에서는 피부온 센서를 이용한 인체표면 온도분포 측정시스템을 개발하기 위하여 각 센서의 위치와 간격, 그리고 인체 곡면을 따라서 보간법에 따라 온도분포 결과에 미치는 영향을 파악하고 적외선 화상 결과와 비교하고자 한다.

• Journal of Biosystems Engineering
• /
• v.22 no.4
• /
• pp.479-486
• /
• 1997

식물 뿌리에 대한 지식은 식물-토양 사이의 관계 이해, 토양의 호율적 관리, 식물에 의한 영양분과 수분의 흡수 과정 이해, 그리고 토양 등급 지수를 만드는데 있어서 아주 중요하다 식물 뿌리에 관한 정보를 정량화하기 위하여는 뿌리를 흙으로부터 씻어내고 뿌리의 길이, 표면적, 중량과 같은 식물 뿌리의 특성을 측정하여야 한다 하지만 이렇게 뿌리를 씻어 낸 다음 뿌리의 특성을 측정하는 기존의 방법을 이용할 경우 막대한 시간과 노동력이 필요하여 뿌리에 관한 많은 양의 정보를 얻는데 큰 어려움이 있다. 이 연구에서는 식물 뿌리를 관측하는데 필요한 시간과 노동력을 줄일 수 있는 식물 뿌리 측정법을 세선 작업과 자외선 명암 증진법을 이용한 영상 정보 처리 장치를 바탕으로 하여 개발하였다. 개발된 화상 정보 처리 장치를 이용하여 옥수수 뿌리의 길이를 재었을 때 기존의 뿌리 길이 측정 방법보다 2.5 배 발리 측정할 수 있는 것으로 나타났다.