본 고는 반도체 재료가 갖는 자기효과를 이용하여 자기센서의 종류 및 특성등에 대하여 서술하였다. 반도체 LSI의 응용분야가 확대됨에 따라서 반도체 센서를 이용한 극소형화, 고성능화, 저가격화, 다기능화등이 가능하게 되었다. 이러한 상황에서 반도체를 이용한 홀 소자나 자기저항 소자와 같은 자기센서 등을 주변회로와 일체화시킨 초소형 시스템에 대한 연구가 활발하다. 특히 화합물 반도체는 자기센서에 적합한 물리적인 특성을 갖고 있기 때문에, 자기센서로 효율을 나타내고 있다. 반도체의 미세가공기술의 발전과 LSI제조기술의 발전을 이용하여 센서의 집적화, 저가격화를 가능하게 하였으며, 다른 종류의 반도체 센서들을 자기센서와 함께 하나의 칩위에 장착할 수 있는 응용집적센서(Application-specific Integrated Sensor)가 더욱 중요한 역할을 할 것이다.
Kim, Sung-Woo;Park, Sung-Hyun;Ryu, Jee-Youl;Lee, Dong-Hyun;Noh, Seok-Ho
Proceedings of the Korean Institute of Information and Commucation Sciences Conference
/
2010.10a
/
pp.740-743
/
2010
본 논문에서는 홀 효과를 이용하여 차축(Tone Wheel) 회전에 따른 자속밀도의 변화를 감지하여 속도를 검출하는 자동차용 차륜 속도센서를 개발 제작하였다. 개발된 센서는 능동형 차속센서로서 마그네트 내장형 2-wire 홀 IC와 케이블 연결부를 ABS를 이용 하우징한 모형 구조로 제작 실험하였다. 기존의 능동형 차속센서 중 1개사의 자동차용 차속센서 부품의 특성을 분석하여 본 논문에서 제작한 센서와 각 특성을 비교하였다. 본 논문에서 개발된 차속센서는 12km/h 이하에서의 최소 감지스피드 성능, $80^{\circ}C$이하의 작동온도, 49% ~ 51%의 듀티 사이클$[T_{on}/(T_{on}+T_{off})]$ 동작 특성을 보였다. 본 논문에서 제작한 능동형 차속센서는 수동형과 비교하여 부품수가 적고 소형화 및 경량화, 에어 갭(Air Gap) 변화에도 민감하지 않으며 듀티 사이클과 저속에서의 검출능력이 우수한 특성을 지닌다.
수도 원격검침을 위한 수도미터의 측정방법이 리드스위치, MR 센서방식, 엔코더방식, Cyble 방식등 다양하게 제시되고 있다. 그러나, 홀효과를 이용한 반도체 소자로 제공되는 Hall IC방식의 경우 많은 장점이 있으나 수도 원격검침분야에 적용된 사례가 전무하여 본 연구를 통하여 Hall IC방식이 원격검침용 수도미터에 적용하여 효과적 사용이 가능한지 적용성을 분석코자 한다.
Proceedings of the Korean Society of Computer Information Conference
/
2020.07a
/
pp.327-328
/
2020
본 논문에서는 저전력 저비용 임베디드 환경에서 PCB 검사 기법을 제안한다. 특히, IC 미삽에 대한 검출 알고리즘을 제안하고 실험한다. 고사양의 컴퓨팅 시스템에서는 CNN과 같은 딥러닝 뉴럴 네트워크를 사용하여 특별한 알고리즘을 고려하지 않아도 대규모의 데이터를 입력함으로써 모델을 완성하고 이를 통해 PCB 검사를 수행할 수 있다. 그러나 데이터의 양이 충분하지 않거나 충분한 전력과 비용을 투입하지 못하는 임베디드 환경에서는 각 부품에 따른 컴퓨터 비전 알고리즘이 필요하다. IC의 경우 타부품에 비하여 형태가 직사각으로 정형화 되있으며 색상도 균일한 특징을 가지고 있기에 미삽에 대한 검출이 가능하다. 베어보드(Bare Board)의 색상과 IC 부품의 색상이 확연히 다를 경우에는 RGB 픽셀을 카운트 하는 히스토그램 카운팅 알고리즘만으로 검출이 가능하다. 베어보드의 색삭과 IC의 색상이 유사할 경우에는 베어보드의 핀 혹은 홀의 형태를 감지하여 검출이 가능하다. 본 논문에서는 베어보드의 색상와 IC의 색상이 같을 경우에 다를 경우를 나누어 미삽 검사를 수행하고 그 정확도를 확인한다.
Journal of the Korean Institute of Telematics and Electronics A
/
v.32A
no.1
/
pp.138-145
/
1995
The offset voltage in silicon Hall plates is mainly caused by stress and strain in package, and by alignment in process. The offset voltage is appeared random for condition change with time in the factory, is non-linearly changed with temperature. In this paper proposed new method of design of Hall IC, and methematicaly proved relation layout of chip of 90$^{\circ}$-shift-current Hall plate pair is matched with "Differentail to single ended Conversion amplifier." In the experiment, the offset voltage is reduced about 1/100 time than the original offset voltage.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
v.20
no.4
/
pp.56-64
/
2006
Generally, Permanent Magnet Brushless DC Motor(PM BLDC) is necessary the Hall-IC to detect the rotor position. But it will take place the operation standstill of motor or error of rotor position detection according to the circumference temperature, humidity, or limited surroundings. This paper propose the algorithm of rotor position detection only using one or two Hall-IC. Therefore we can estimate information of the others phase in sequence through a rotor instead of using three Hall-IC at 3 phase motor. This paper identify the same characteristics, performance and function of protection circuit by the proposed algorithm with the 3 phase PM BLDC motor in comparison with general method.
In this paper we present an integrated Hail sensor It for fan motors, fabricated in industrial bipolar process. As a discrete Hall sensor and signal processing circuitry In the fan motor system were Integrated into single chip a temperature dependence of Hall sensitivity and Hall offset voltage can be compensated and cancelled by on-chip circuitry. We Propose a novel temperature compensation of Hall sensitivity with negative temperature coefficient (TC) using the differential amplifier gain with Positive TC. After a package of the chip was sealed using a plastic Package 20 Pins, the thermal and magnetic characteristics were investigated. The obtained experimental results are in agreement with analytical predictions and have more excellent performance than\ulcorner conventional the fan motor system using discrete Hall sensor.
Transactions of the Korean Society of Automotive Engineers
/
v.21
no.5
/
pp.1-7
/
2013
The present paper relates to a development of the Gear Detection Sensor for automotive manual transmission. To detect air gap from control finger to detecting zone of sensor based on non-contacted method, permanent magnet and linear type Hall IC are mounted in this sensor. Control finger is machined to 3 step heights to detect 3 gear stages such as In-Gear, Normal and Rear. After conducting actual experimentation based on exclusive Jig and FEM, it is described to consider possibility for automotive application of Gear Detection Sensor.
Yoon Y. H.;Kim Y. C.;Lee S. S.;Won C. Y.;Choe Y. Y.
The Transactions of the Korean Institute of Power Electronics
/
v.9
no.6
/
pp.536-543
/
2004
Slotless Permanent Magnet Brushless DC Motor(PM BLDC) with the characteristics of high speed and power density has been more widely used In Industrial and factory machine. Generally, PM BLDC meter is necessary that the three Hall-lCs evenly be distributed around the stator circumference in case of the 3 phase motor. The Hall-ICs are set up in PM BLDC Motor to detect the main flux from the rotor. therefore the output signal from Hall-ICs is used to drive a power transistor to control the stator winding current. However, instead of using three Hall-ICs, if it used only one Hall-IC, we can estimate information of the others phase in sequence through a rotor This paper identified the characteristics and performance by using one Hall-IC with the 3-phase, 2-pole, 6-slot PM BLDC motor.
SiGe integrated circuits are being used in the field of high-speed wire/wireless communications and microwave systems due to the RF/high-speed analog characteristics and the easiness in the fabrication. Reducing the resistance variation in SiGe thin film resistors results in enhancing the reliability of integrated circuits. In this paper, we investigate the causes that generate the resistance nonuniformity after the silicon-based thin film resistor was fabricated, and consider the counter plan against that. Because the Ti-B precipitate, which formed during the silicide process of the SiGe thin film resistor, gives rise to the nonuniformity of SiGe resistors, the boron ions should be implanted as many as possible. In addition, the resistance deviation increases as the size of the contact hole that interconnects the SiGe resistor and the metal line decreases. Therefore, the size of the contact hole must be enlarged in order to reduce the resistance deviation.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.