• The Journal of Engineering Geology
• /
• v.17 no.4
• /
• pp.525-534
• /
• 2007

The peculiarity of end-expanded soil nailing method(EESNM) is in fixing the wedge-type steel body spreaded by collars and grouting its surroundings by cement milk within soils, after extending hole bottom over drilling hole diameter with top drill bit. The present study was done to establish the effect of this method. Laboratory model test were carried out to investigate the behavior characteristics with the performance of the pull-out test and failure experiment, after preparing soil test box having 1,300mm length, width 1,000mm, and height 1,100mm, and the same experimental condition was set up to compare with the general soil nailing method(GSNM). The pull-out force of about 23 percentage was increased, and the horizontal displacements 1.2 from 9.1 percentage in soil-nailed wall decreased in EESNM compare with GSNM. The axial force acting on nail increased considerably at load level over 7 ton in EESNM and 5 ton in GSNM. The predicted failure line from the maxima analyzed by axial tensile strain located at long distance from soil-nailed wall in EESNM. The EESNM demonstrated the superiority of reinforcement effect in comparison with GSNM from the results above mentioned.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3336-3344
• /
• 2014

The purpose of this study is small scale coagulation module is developed and demonstrated through a lab-scale test. Recent as a sewage treatment rate increases, have heightened the interest in the necessity on the nonpoint source and developing a small processing unit has been increased. Coagulation sedimentation module in this study is additional growth of floc through swirling in the outside zone, reduction of microstructure floc number and the internal settling zone through vertical/level flow complex sedimentation method after the coagulation process precipitation method as an effective high separation efficiency can be divided was also assessed. Coagulation sedimentation module can increase the load factor was 4.4 times compared to conventional clarifier base on the same volume and surface area through vertical/level flow. In this study, this process was selected formation and maintenance of swirling and uniform flow distribution in the internal settling zone as an important design factor, to derive its FLUENT was used to characteristics of the flow model. Through the simulation of swirling, influent velocity, dimensions of external basin, hopper depth of bottom cone was determined and through analysis of velocity distribution, flow distribution detailed specifications are derived like as diameter and number of effluent hole. Lab-scale($120{\ell}/hr$) test results, influent of 300~800 NTU to less than 10 NTU without polymer feeding was able to operate in the 20minutes retention time(surface loading rate $37.3m^3/m^2$-day), and through analysis FLUENT the possibility of using design parameters were derived.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.216-220
• /
• 2006

One of the approaches for reducing the size of the quarter wavelength monopole antenna is the helix and the stacked structure. This paper presents a formula for the relationship between the geometrical parameter and the operating frequency of a slacked helix chip antenna. The stacked helix chip antenna was designed for PCS/IMT-2000 dual-bands operation. The fabricated antenna uses an FR-4 substrate with relative permittivity of 4.2, and its dimensions are $15{\times}7.5{\times}0.4mm^3$. The measured impedance bandwidth (VSWR<2) is 400MHz at the operating frequency.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.4
• /
• pp.63-69
• /
• 2007

We investigated interconnection processes using Cu vias for MEMS sensor packages. Ag paste layer was formed on a glass substrate and used as a seed layer for electrodeposition of Cu vias after bonding a Si substrate with through-via holes. With applying electrodeposition current densities of $20mA/cm^2\;and\;30mA/cm^2$ at direct current mode to the Ag paste seed-layer, Cu vias of $200{\mu}m$ diameter and $350{\mu}m$ depth were formed successfully without electrodeposition defects. Interconnection processes for MEMS sensor packages could be accomplished with Ti/Cu/Ti line formation, Au pad electrodeposition, Sn solder electrodeposition and reflow process on the Si substrate where Cu vias were formed by Cu electrodeposition into through-via holes.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.465-472
• /
• 2008

Fabrication of nanostructured materials and synthesis of nanomaterials have intensively studied to realize electronic devices for nanotechnology. By using nanoporous alumina mask, nanostructured material can be fabricated in the form of uniform array. The size and the density of the nanostructured materials can be controllable by changing the pore diameter and the density of the alumina mask. This method is possible low cost and on large scale process, and feasible to contribute the fusion technology consisting of information technology, nanotechnology, and biotechnology. Therefore, these techniques provide alternative approaches for development of new electronic applications. In this paper, the fabrication technique and its applications of nanoporous alumina mask are described and nanostructured materials such as quantum dots, nanoholes, and nanorods are introduced.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1151-1159
• /
• 2012

Spray visualization and computer simulation of a DME injector have been conducted to investigate the enlarged injection hole diameter effect. To increase the reliability of the computational result, simulation results have been compared with the visualization test results, and the behaviors of a DME spray under various high-pressure and -temperature conditions have been computed. This study shows a discrepancy of 3.57% between the experimental and the computational results of penetration length for an injection pressure of 35 MPa and ambient pressure of 5 MPa. When simulating the engine conditions, the maximum penetration length of a fully developed DME spray is 42 mm when the temperature to pressure ratio is 300 K/MPa. The DME spray behavior is dominantly affected by the ambient pressure under the condition that the ratio is less than 300 K/MPa, and by the ambient temperature under the condition that the ratio is more than 300 K/MPa.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.4
• /
• pp.373-379
• /
• 2010

EMAT has been applied in various fields for flaw detection and material characterization because it has noncontact property in wave generation and a good mode selectivity. Unfortunately, however, EMAT shows low signal to noise ratio relative to commercial contact transducer because of low energy conversion efficiency. If the phase matching through the control of time delay between each coil consisting of the array EMAT is accomplished, it is expected that it will be a solution for the improvement of low signal to noise ratio. In this experiment, the phased array EMATs which consists of 3 or 4 meander coils and one big magnet were fabricated for surface and vertical shear wave generation. Effect of phased delay control on signal directivity and amplitude enhancement was verified. A slit with the depth of 0.5 mm and a side-drill hole of 0.5 mm diameter were clearly detected by fabricated phased array EMATs, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.96-96
• /
• 2016

나노섬유(nanofiber), 나노선(nanowire), 그리고 나노튜브(nanotube)와 같은 1차원 구조의(one-dimensional structure) 나노재료는 벌크(bulk) 및 박막(film) 재료와는 다르게 물리적, 화학적으로 특이한 성질을 가지고 있으며, 이러한 성질은 나노재료의 구조, 형상, 크기 등에 큰 영향을 받는다. 첫 째, 전기방사(electrospinning) 공정을 이용한 나노섬유의 합성; 용액의 특성, 전기장 세기, 방사시간 등의 변수를 조절하게 되면 방출되는 재료의 형상을 입자 혹은 섬유상의 형태로 얻을 수 있으며, 전기방사를 통해 합성된 나노재료의 소결 온도 및 시간을 달리함으로써 나노입자의 크기를 조절할 수 있다. 또한, 템플레이트 합성법(template synthesis) 및 이중노즐(coaxial nozzle)을 이용해 속이 빈 형태인 중공(hollow) 구조의 나노섬유를 얻을 수 있으며, 전기방사에 사용되는 전구물질에 원하는 금속 및 산화물을 첨가함으로써 복합체(composite) 나노섬유를 얻을 수 있다. 둘 째, VLS(Vapor-Liquid-Solid) 공정을 이용한 나노선의 성장; 온도, 압력, 전구물질의 양, 그리고 시간 등의 변수를 조절하게 되면 원하는 직경 및 길이를 갖는 나노선을 성장시킬 수 있다. 그리고 ALD(Atomic Layer Deposition)를 이용해 나노선에 추가적인 층을 형성함으로써 코어-셀 구조를 형성할 수 있으며, 감마선, UV와 같은 공정을 이용해 귀금속 촉매를 나노선에 기능화 시킬 수도 있다. 코어-셀 구조를 갖는 나노선/나노섬유는 코어 혹은 셀 층의 전자나 홀의 이동을 유발하여 전자공핍층(electron depletion layer) 또는 정공축적층(hole accumulation layer)을 확대 및 축소시켜 센서의 초기저항을 증가시키거나 감소시키는 역할로써 이용되고 있으며, 특히, 셀 층의 두께가 셀 층 재료의 Debye length와 유사한 크기를 갖게 되면, 셀 층은 완전공핍층(fully depleted layer)을 형성해 최대의 감도를 나타낼 수 있다. 본 연구에서는 다양한 제조 공정을 통해 제작될 수 있는 1차원 나노-구조물을 가스센서에 적용하는 사례들을 소개하고, 이러한 가스센서의 감응성능을 향상시키기 위한 방법의 한 가지로 원자층증착법으로 나노선/나노섬유의 표면에 셀층을 형성하여 감응성 향상 메커니즘 및 관련 주요 변수들을 조사하고자 한다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1415-1426
• /
• 2008

Stone columns, locally called "GCP (granular compaction pile)" can be used to improve strength and resistance against lateral movement of a foundation soil like rigid piles and piers. Also installation of such a discrete column facilitates drainage, and densifies and reinforces the soil in the sense of ground improvement. The integrity of the GCP has been indirectly controlled with the records of each batch including depth and the quantity of stone filled. An integrity testing was attempted using crosshole S-wave logging. The method is conceptionally same as the crosshole sonic logging (CSL) for drilled piers. The only and critical difference is that S-wave should be used in the logging, because P-wave velocity of the stone column is less than that of ground water. The crosshole sonic logger does not have the capability to measure S-wave propagating through the skeleton of crushed stone. An electro-mechanical source, which can generate either P- or SH-waves, and a 1-D geophone were used to measure SH-waves. Two 76mm diameter cased boreholes were installed 1 meter apart across the nominal 700mm diameter stone column. At every 10cm of depth, shear wave was measured across the stone column. One more borehole was also installed 1 meter outward from the one of the above boreholes to measure the shear wave profile of the surrounding soil. The diametric variation of the stone column with respect to depth was evaluated from the shear wave arrival times across the stone column, and shear wave velocities of crushed stone and surrounding soil. The volume calculated with these variational diameters is very close to the actual quantity of the stone filled.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.6
• /
• pp.4322-4327
• /
• 2015

Improper backfill materials and compaction controls under pipelines have become one of the major causes of failure in many sewage pipeline systems. A study on backfill materials and compaction controls has been considered for a long time. However, structural supporters under the pipe were recently concerned because of pipeline repair and maintenance. This paper presents a prefabricated plastic foundation for supporting a sewage pipe system and increasing the performance function of the pipes. Several analytical models for the plastic foundations were investigated using finite-element program, ABAQUS, for checking safety. Comparing with the results of analyses, some of economic design sections based on the sizes of pipe diameters, 600mm, 700 and 600mm, were evaluated. These results could be applied to a pipeline system with a prefabricated plastic foundation with respect to pipe diameters and buried depths.