• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.5
• /
• pp.54-60
• /
• 2017

In order to identify the characteristics of the flame transfer function gain, cold-flow transfer function was introduced, which is the part of the combustion instability research. Nitrogen and carbon dioxide was used to obtain the cold-flow transfer function and input/output variables was measured by hot wire anemometry. Density and fluid flow rate affect the cold-flow transfer function gain and peak frequency. In addition, acoustic resonance frequency affects the peak frequency of gain in the fuel feeding line.

• Journal of the Korean Institute of Gas
• /
• v.9 no.1 s.26
• /
• pp.9-15
• /
• 2005

Hydrogen is considered to be the most important future energy carrier in many applications reducing significantly greenhouse gas emissions, but the safety issues associated with hydrogen applications need to be investigated and fully understood to be applicable as the carrier. Therefore, there is a considerable demand for further research concerning the dispersion of hydrogen/air mixture clouds and the possible consequences of their ignition. In this study, the dispersion of hydrogen gas in atmosphere has been analysed with atmospheric condition by concerning the buoyancy of hydrogen. The hazard ranges to wind direction increase with wind speed and the stability of atmosphere. The concentration of hydrogen at just above ground is nearly zero due to buoyancy of hydrogen gas. Therefore, the ignition probability of hydrogen gas cloud is low and the hazard of explosion or fire associated with hydrogen gas is relatively low comparing with the other fuel gas such as propane or butane.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.495-501
• /
• 2012

Spray characteristics of liquid jets in crossflow, which can be observed in the liquid jet injection system of a gas turbine or ramjet engine, were experimentally investigated. By measuring liquid jet penetration in the case of single orifice and double orifice injectors, the experimental formula for jet penetration was modified to consider penetration distances greater than that considered in a previous study. The changes in spray characteristics resulting from changes in the liquid jet and crossflow pressure, including SMD and jet disintegration, were carefully studied. Specifically, the jet penetration was measured for different injector shapes, and in the case of a double orifice injector, the penetration of the rear orifice jet was found to be greater by approximately 20% ($L_h$ = 4 mm) compared to that in the case of a single orifice injector because of the influence of the front orifice.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.9
• /
• pp.837-845
• /
• 2013

An airlift pump can be used to pump liquids and sediments within itself, which cannot easily be pumped up by a conventional method, by using the airlift effect. This characteristic of the airlift pump can be exploited in a DCFC (Direct Carbon Fuel Cell) so that molten fuel with high temperature may be carried or transported. The basic characteristics of airlift are investigated. A simple system is constructed, where the reservoir is filled with water, a tube is inserted, and air is supplied from the bottom of the tube. Then, water is lifted and its flow rate is measured. Bubble patterns in the tube are observed in a range of air flow rates with the parameters of the tube diameter and submergence ratio, leading to four distinct regimes. The pumping performance is predicted, and the correlation between the supplied gas flow rate and the induced flow rate of water is found.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.2
• /
• pp.147-152
• /
• 2014

In this research, polysulfone hollow fiber membrane was used to recover $CO_2$ which is one of greenhouse gases from flue gas stream being emitted after the combustion of fossil fuels. The prerequisite requirement is to design the membrane process producing high-purity $CO_2$ from flue gas. For separation of $CO_2$, a membrane module and flue gas containing 10% carbon dioxide was used. The effects of operating conditions such as pressure, temperature, feed gas composition and multi-stage membrane on separation performance were examined at various stage cuts. Higher operating pressure and temperature increased carbon dioxide concentration and recovery ratio in permeate. Recovery ratio and separation efficiency increased if a higher content of $CO_2$ injection gas composition. Three-stage membrane system was producing a 95% $CO_2$ with 90% recovery from flue gas. The separation efficiency of three-stage membrane system was higher than one-stage system.

• Journal of Energy Engineering
• /
• v.25 no.3
• /
• pp.9-17
• /
• 2016

In this study, a method for CO reduction using char-coal combustions was developed with lignin and glycerin as combustion improvers. The relationship between CO emission and the combustion improvers was confirmed by measuring the CO concentration. The experiment to determine the combustion characteristics was conducted using glycerin, which shows high combustibility at low temperatures, impregnated with lignin, which has a specific surface area. The combustibility, volatility, and CO concentration were measured using thermo-gravimetric analysis(TGA), and gas chromatography-mass spectrometry(GC-MS). This study presents the optimal CO reduction ratio, which occurred when the combustible material contained a 20% blend of combustion improvers. This resulted in a 20-30% CO reduction rate compared to that achieved with normal char-coal.

• Fire Science and Engineering
• /
• v.27 no.3
• /
• pp.20-29
• /
• 2013

To investigate numerically the effects of geometry and location of vertical opening on the thermal and chemical fire characteristics in full-scale under-ventilated compartment fires, the ventilation factor ($A\sqrt{h}$) to estimate a theoretical maximum inflow of ambient air and the mass loss rate in a heptane pool fire were fixed for all cases. It was shown that variations in door geometry affected significantly the change in thermal and chemical characteristics inside the compartment. Variations in window location resulted in the complex change in additional fire characteristics including the fire duration time and recirculating flow structure. These results were analyzed in details by the multi-dimensional flow and fire characteristics including the vent flow and fuel/air mixing phenomena.

• Fire Science and Engineering
• /
• v.23 no.1
• /
• pp.55-62
• /
• 2009

A general combustion characteristics of forcing nonpremixed jet in laminar flow rates have been conducted experimentally to investigate the effect of forcing amplitude with the resonant frequency of fuel tube. There are two patterns of the flame lift-off feature according to the velocity increasing; one has the decreasing values of forcing amplitude on the lift-off occurrence when a fuel exit velocity is increasing, while the other has the increasing values. These mean that there are the different mechanisms in the lift-off stability of forced jet diffusion flame. Especially, the characteristics of attached jet flame regime are concentrically observed with flame lengths, shapes, flow response and velocity profiles at the nozzle exit as the central figure. The notable observations are that the flame enlogation, in-homing flame and the occurrence of a vortical motion turnabout have happened according to the increase of forcing amplitude. It is understood by the velocity measurements and visualization methods that these phenomena have been relevance to an entrainment of surrounding oxygen into the fuel nozzle as the negative part of the fluctuating velocity has begun at the inner part of the fuel nozzle.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.121.2-121.2
• /
• 2011

석탄가스화복합발전과 연계하여 사용할 수 있는 $CO_2$분리법으로 연소 전 탈탄소화는 연료가 연소되기 전에 $CO_2$를 회수하는 방법으로 현재 여러가지 분리법이 사용되고 있다. 본 연구에서는 가스 하이드레이트의 다양한 응용 분야 중 이산화탄소 격리분야에서 합성가스로부터 $CO_2$롤 효과적으로 분리/회수하기 위하여 가스 고형화법에 관한 연구를 진행하였다. 가스 하이드레이트 형성과정에서의 반응 특성을 살펴보기 위하여 순수계와 촉진제 첨가계(TBAB, TBAF, THF)에 대하여 반응시간에 따른 가스소모량 및 기상의 $CO_2$ 조성 변화를 측정하였다. 그 결과 하이드레이트 상에 고농도의 $CO_2$가 포집되는 것을 확인 할 수 있었다. 순수계와 THF 첨가계의 경우 가스 소모량이 다른 계에 비하여 높게 나타났다. 이는 순수계의 경우 구조-I의 큰 동공과 작은 동공에 모두 기체가 점유되기 때문이며, THF 첨가계의 경우 구조-II의 큰 동공에만 기체가 점유되지만 THF의 첨가로 인해 전환율이 증가되기 때문이다. 반면, TBAF와 TBAB 첨가계의 경우에는 상재적으로 낮은 가스 소모량을 보였다. 기체 소모량이 큰 경우 최종 기상의 $CO_2$ 조성이 낮게 나타났다. 그리고 모든 실험조건에서 1시간 이내에 하이드레이트 형성반응이 종결되는 것을 확인할 수 있었다. 또한, 촉진제 첨가에 의한 하이드레이트의 구조적인 변화를 확인하기 위하여 Raman 분광법과 $^1H$-NMR을 이용하여 혼합가스 하이드레이트를 분석하였다. 본 실험으로 얻어진 결과는 가스 고형화법을 이용한 합성가스 분리 공정 설계 및 개발에 중요한 기초자료가 될 것으로 사료된다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.4
• /
• pp.140-146
• /
• 2010

An experimental study was carried out to investigate the emission characteristics for various alternative fuels in a 2.0 liter 4-cylinder turbo-charged diesel engine. The conventional diesel fuel, neat GTL (Gas to Liquid), blends of diesel and biodiesel(BD20), and blends of GTL and biodiesel(G+BD20 and G+BD40) were applied, and their emission characteristics were compared at various steady-state engine operating conditions. A noticeable reduction of exhaust emissions compared to conventional diesel fuel, except for NOx emission, was observed for G+BD40, where there is a maximum 30% averaged reduction for gaseous emissions (THC and CO) and 70% for PM mass concentrations. When comparing PM size distributions for biodiesel blended fuels, the PM number concentration in accumulation mode, where the diameter of PM is greater than 50 nm, decreased due to additional oxygen content in the biodiesel fuel; in nucleation mode, where the diameter of PM is less than 50nm, there was a slight increase or decrease in the PM number concentration depending on the amount of oxygen available in the combustion chamber.