• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.1057-1063
• /
• 1994

An instantaneous frequency analysis is a technique to examine a signature for the rotating machinery if the signal has several transitions within a cycle. This paper discusses the conditions of existing negative frequency components in the instantaneous frequency. By using a signal consisted of two frequency components, the instantaneous frequency analysis is conducted while the amplitude ratio between two frequency components has been changed. The analysis shows that, depending on the amplitude ratio, the instantaneous frequencies have averaged, zero-valued, or negative components. It turns out that the negative-valued instantaneous frequencies, which have been regarded as the noise effect, are the consequence of the calculation process for the multisignal components. The criteria of existing the negative values in instantaneous frequencies is given in terms of the relative amplitude ratio and the frequency difference. Especially when the amplitude ratio approaches to 1, the instantaneous frequency fluctuates ${\pm}\infty$ in theory, which implies that instantaneous frequency has unstable region around the amplitude ratio, 1.Also, as the frequency difference between major signal components is increased, the region of existing negative instantaneous becomes broader. In an instantaneous frequency analysis, therefore, a narrow band analysis is suggested, with extreme care if the amplitude ratio approaches to 1. In this paper, a vibration signal monitored from a rotating machinery is also examined as an application example in order to show the existence of negative instantaneous frequencies components.

• Journal of Advanced Navigation Technology
• /
• v.11 no.1
• /
• pp.9-16
• /
• 2007

In this paper, the Bit Error Ratio (BER) performances of the D8PSK modulation schemes for VDL Mode-2 are analyzed according to the matched and unmatched cases of the channel filters. The carrier frequency and phase offset effects are analyzed with unmatched case. Generally in digital transmission techniques, the Root Raised Cosine filters which are used as channel filters are applied to both sides at transmitter and receiver in order to achieve no ISI, but in VDL Mode-2, the Raised Cosine Filter is used only in transmission section and the receiver section uses general low pass filter, therefore we could not achieve ISI reduction effects but can have better spectrum quality. From the simulation results, the error probability is increased slightly (1~2dB) with use of un-matched channel filter, we got the conclusions that carrier phase offset do not effect to bit error ratio, but the frequency offset effect is so serious. Finally, narrow band D8PSK modulation signals are generated by the use of Digital Up-Converter and then its features are compared with analog modulator.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.4
• /
• pp.468-480
• /
• 1993

In this paper, at first, the characteristics of double mode SAW (DMS) resonator are analysed by applying the wave guide model and coupled mode theory to 1-port resonator. The DMS resonators (2-pole), which are arranged in a close, parallel configuration of two identical 1-port resonators on a single plate, and 4-pole DMS filters are designed and fabricated at the center frequency of 150.15 MHz with 3-dB bandwidth of 80 KHz. The empirical design characteristics are obtained from the comparison of experimental and theoretical values resulted from several fabrications, and the narrow bandpass filters are implemented on the basis of the above empirical results, which can be used to mobile communication systems. A ST-cut quartz substrate is selected for the stable temperature-frequence characteristics, and high resolution photolithography is applied to the fabrication of filter to get the fine electrode patterns.

• Journal of Satellite, Information and Communications
• /
• v.10 no.3
• /
• pp.26-31
• /
• 2015

This paper deals with a size-reduced Ku-band waveguide limiter. Basically, it passes the signal from 16.125 GHz through 16.375 GHz, but when excessively high power is injected to the input port, it should change to a bandstop filter. Furthermore, it is required to change to bring attenuation by more than 20 dB and 50 dB over a narrow band and the entire passband, respectively. Therefore, in order to meet this requirement, a limiting device is implemented with multiple PIN-diode posts that enable the limiter to be the bandpass filter and stopband one at the off and on states of the PIN-diode switch, respectively. So, the design goes through the equivalent circuit modelling and the geometry is realized in the accurate electromagnetic analysis CAD tool. Finally, the result is discussed to shed light on whether it complies with the aforementioned requirement.