• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.636-643
• /
• 2008

The objective of this paper is to assess the potential use of the geogauge and the light falling weight deflectometer (LFWD) and the soil impact hammer as quality control/quality assurance $Q_C/Q_A$ devices for compacted soil layers. A comprehensive field experimental program considering variation of number of compaction, water contents and thickness of compaction layer was conducted on compacted layers of gravel sand. The geogauge, LFWD, the soil impact hammer and static load test (PLT) as a reference test were performed for the compacted layers. The geogauge elastic modulus, $E_G$, the LFWD dynamic modulus, ELFWD, empirical soil stiffness, $K_{30}$, obtained from soil impact hammer and soil stiffness directly obtained from PLT, $K_{30}$, were correlated with increasing number of compaction. The results of this study show that the geogauge, LFWD and the soil impact hammer, which are very simple to test, can be used as substituting devices for static PLT which is a conventional quality control/quality assurance $Q_C/Q_A$ devices for compacted soil layers.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.5
• /
• pp.117-126
• /
• 2004

Recently, the top ＆ down method with drilled shafts as a foundation of high rise building is often adopted for the purpose of construction period reduction and construction cost effectiveness. It is common to omit the loading test as a quality assurance on account of the high capacity of drilled shafts for the top ＆ down method. It seems that the capacity of drilled shaft in recent top ＆ down method is beyond that of conventional loading test method. However, the quality assurance for the drilled shaft as foundation of high rise building becomes much more important since the drilled shaft should bear much higher working load. A small scale test pile can be an alternative as a quality assurance for the drilled shaft with hish capacities. Through a case study, this paper gives an idea for solving the limitation of the conventional loading test method for the quality assurance of drilled shaft with high capacities. In particular, this paper analyzed the scale effect for a small drilled shaft installed into bedrock, which could be used for an alternative.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.5
• /
• pp.135-143
• /
• 2004

In the land section of marine bridge construction site, to confirm the end bearing of large diameter drilled shaft constructed in the fault zone which was discovered unexpectedly, the hi-directional end loading tests were performed. The objectives of this study are to confirm the end bearing of the pile constructed in fault zone and the increasing effect of end bearing after grouting the base ground beneath the pile toe. After grouting the pile base ground, the settlement of pile base decreased considerably and the pile base resistance increased more than twice.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.520-529
• /
• 2006

그 동안 몇 차례 오스터버그 셀$(O-cell^{\circledR})$을 이용한 양방향 말뚝 재하시험기법이 국내에 성공적으로 소개/적용된 바 있다. 이 방법은 상대적으로 새롭고 독특한 방법으로서 시험비용과 기존 재래적인 시험방법이 적용상 제한을 받는 경우나 대규모 시험에서 발생할 수 있는 문제점들을 극복할 수 있다. 국내에서는 설계목적을 위한 시험말뚝 뿐 아니라 설계하중이 큰 실제말뚝에 대한 시험이 증가하는 추세에 있다. 이 논문에서 소개하는 양방향 재하시험 방법을 적용하면 기존의 소규모 재하시험 방법에서 발생될 수 있는 주면 마찰력과 선단지지력의 분리측정이나 각각의 지지력에 대한 극한상태를 확인하지 못하는 한계를 극복할 수 있고 시험하중이 270MN을 초과하는 경우까지 적용할 수 있는 장점을 갖고 있다. 본 논문에서는 오스터버그 셀을 이용한 정적 재하시험 방법에 대하여 말뚝종류별로 상세히 기술하였으며 이 시험방법의 장점과 국내현장에 적용되었던 사례를 소개하였다.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.11
• /
• pp.5-15
• /
• 2013

The end bearing capacity of rock-socketed drilled shafts under axial loading is investigated by Hoek-cell tests and a numerical analysis. From the test results, it was found that the ultimate end bearing capacity ($q_{max}$) was influenced by pile diameter, rock mass modulus and the spacing of discontinuity. A new ultimate end bearing capacity method is proposed by taking end bearing capacity influence factors, including rock mass discontinuity, based on field data. Through comparisons with other field data, the proposed $q_{max}$ method represents a definite improvement in the prediction of ultimate end bearing capacity of rock-socketed drilled shafts.

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.1
• /
• pp.45-51
• /
• 2005

The distribution of shaft resistance is measured by the static load test with the strain gauge or stress gauge, so that the long-term load distribution must be considered for the pile design. However, the measurement by strain gauge generally assumes the 'zero reading', which is the reading taken at 'zero time' with 'zero' load and the residual stress, which is the negative skin friction(or the negative shaft resistance) caused by the pile construction, is neglected. Therefore, the measured value by strain gauge is different from the true load-distribution because residual stresses were neglected. In this study, the three drilled shafts were constructed, and the strain measurements were carried out just after shaft construction. As a result of this study, it is shown that the true load-distribution of drilled shaft is quite different with known load distribution and the true load-distribution of drilled shaft changed from the negative skin friction to the positive skin according to the load increment.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.6
• /
• pp.67-79
• /
• 2005

The field plate load test has a good potential for determining modulus since it measures both plate pressure and settlement. Conventionally the modulus has been assumed to be a constant secant value defined from the settlement of the plate at a given load intensity. A constant modulus (modulus of subgrade reaction, k), however, may not be a representative value of subgrade soil under working load. Field strain(o. stress)-dependent modulus characteristics of subgrade soils, at relatively low to intermediate strains, are important in the pavement design. In this study, the field strain dependent moduli of subgrade soils were obtained using cyclic plate load test. Testing procedure and data reduction method are proposed. The field crosshole and laboratory resonant column tests were also performed to determine field nonlinear modulus at $0.001\%\;to\;0.1\%$ strains, and the modulus values and nonlinear trends are compared to those obtained by cyclic plate load tests. Both modulus values match relatively well when the different state of stress between two tests was considered, and the applicability of field cyclic plate load test for determining nonlinear modulus values of subgrade soils is verified.

• Journal of the Korean Geosynthetics Society
• /
• v.13 no.4
• /
• pp.77-85
• /
• 2014

The helical pile has become popular with some constructional advantages because relatively compact equipment is needed for installing helical piles. However, field loading tests for estimating the bearing capacity of helical piles have drawbacks that the required dead load should be as much as the operation load, and reaction piles or anchors are required. In this paper, the bi-directional load test without necessity of reaction piles and loading frames was applied to the helical pile, and the load-settlement curves of the helical piles were measured. The bi-directional load test was performed in two separate stages with the aid of a special hydraulic cylinder whose diameter is equal to that of the pile shaft. In the first stage, the hydraulic cylinder is assembled immediately above the bottom helix plate, and the end bearing capacity of the helical pile is measured. In the second stage, the hydraulic cylinder is assembled above the top helix plate, and the skin friction of the helical pile is measured. The pile loading-test program was carried out for the two different helical piles with the shaft diameter of 89 mm and 114 mm, respectively. However, the configuration of helix plates is identical with three helix plates of 450-, 350-, 200- mm diameter. Results of the bi-directional load test were verified by the conventional static pile loading test. As a result, the bearing capacity estimated by the bi-directional load test is in good agreement with the result of the conventional pile loading test.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.8
• /
• pp.53-60
• /
• 2013

The compaction control method of national road substructure is using field density test to determine the relative compaction and plate bearing test to check the load bearing capacity. However, these two tests digitize a construction site manager's judgment based on his experience, so mechanical basis is weak. Resilient modulus method, which is recently being used to resolve such problem, is evaluated as a rational design method of pavement structure that can rationally reflect the stress-strain state of pavement materials that is caused by the condition of load repetition of vehicle load. However, the method of measuring the resilient modulus is difficult and lengthy, and it has many problems. To replace it, light falling weight test is recently being proposed as a simple test method. Therefore, this research uses dynamic plate loading test, which quickly and simply measures the elastic modulus of the subgrade and sub-base construction and site of maintenance, to judge the possibility of compaction control of the stratum under the road, and it proposes relation formula by analyzing the result of static load test.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.3
• /
• pp.127-134
• /
• 2008

The response of a bridge can be influenced by span length, bridge's surface condition, vehicle's weight, and vehicle's velocity. It is difficult to predict accurate behavior of a bridge. In the current standard of specifications, such dynamic effect is defined by impact factor and prescribed to consider live load as to increase design load by means of multiplying this value by live load. However, it is not well understood because the Impact factor method differs from every country. Dynamic, static and pseudo-staitic field loading tests on PSC-I girder bridges were carried out to find out the dynamic property of the bridge. This paper is aimed to figure out actual dynamic property of the bridge by using field loading test. An empirical method based on impact factor is widely used and also argued. Displacement and strain response measured from the tests was compared with one from the empirical method. The former seems to be reasonable since it can consider actual response of a bridge through field tests.