• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.296-299
• /
• 2002

The precision blanking of thin sheet metal is important process on production of precision electronic machine parts such as IC leadframe. In the blanking process, the factors that friction coefficient, tool clearance, material properties are the most important factors in the precision blanking process, because these factors affect the sheared face of product, side forces to punch during blanking process and surface condition after blanking process. So, many investigations have been performed. But, the former studies did not take up the characteristic of material. In this paper, in order to investigate the characteristic of blank, such as K(strength coefficient) and n(strain hardening coefficient), on the sheared face of blank and the side force to punch, FE-simulation has been analyzed by means of DEFORM-2D. To obtain input Parameters on FE-simulation, tensile and friction test has been done.

• Tribology and Lubricants
• /
• 제12권2호
• /
• pp.65-73
• /
• 1996

Rapid increase of Refrigeration and Air conditioning system in modem industries brings attention to the urgency of core technology development in the area. This paper presents theoretical investigation of the lubrication characteristics of rotary compressor for refrigeration and air conditioning. In order to analyze the lubrication characteristics of the main & sub bearing of rotary compressor, the bearing force and locus of shaft center are analyzed by the dynamic analysis of rotary compressor and numerical analysis of Reynolds equation as the operating condition is changed in various ways. In this paper, we used the Runge-Kutta method for the dynamic analysis of rotary compressor and the SOR (Successive OverRelaxation) method for the numerical analysis of Reynolds equation. The result shows that the operating condition of sub bearing is severer than that of main bearing, and eccentricity ratio grows as the bearing force increases. It is believed that the result can be applied to the design of alternative refrigerant rotary compressor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.260-265
• /
• 1997

Large dynamic loads act on the rotor in rotary compressors. There are unbalance forces due to eccentric rotation parts and gas forces induced by the difference in pressure between compression and suction gases6 Rotor-journal bearing system is nonlinear since the stiffness and damping coefficients of the lubricating oil film are not constant in the bearings. In this paper, the program for predicting the behaviors of rotor-journal bearing system of rotary compressor is developed. Finite element modeling is used to analyze the flexible rotor. The numerical results are compared with experimental results. The location of balancer weight are suggested for reducing rotor whiring displacement.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1999년도 춘계학술대회 논문집
• /
• pp.344-351
• /
• 1999

Stress analysis of bogie frame by using the finite element method has been performed for the various loading conditions according to the UIC (International Union of Railways) Code 615-4. Multiaxial fatigue damage models such as signed von Mises method and typical critical plane theories were reviewed, and multiaxial fatigue analysis program (MUFAP) has been developed. Fatigue analysis of bogie frame under multiaxial loading was performed by using MUFAP and finite element analysis results. The procedure developed in this study is considered to be useful for the life prediction in preliminary design stage of railway components under multiaxial loading conditions. 3-dimensional surface modeling, mesh generation and finite element analysis were performed by Pro-Engineer, MSC/PATRAN and MSC/NASTRAN, respectively, which were installed in engineering workstation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.330-337
• /
• 1998

Bogie is mainly consisted of the bogie frame, suspensions, wheels and axles, braking system, and transmission system. The complex shapes of the bogie frame and the multiaxial loading condition induced in real operation make it difficult to design the bogie frame against the fatigue. In this study, multiaxial fatigue criteria were reviewed. Stress analysis of the bogie frame has been performed for the various loading conditions according to the UIC Code 615-4. Magnitudes of the stress amplitude and mean stress were estimated based on the stress analysis results to simulate the operating loads encountered in service. Fatigue strength of the bogie frame was evaluated by using the constant life diagram of the material. 3-D surface model ling, finite element meshing, and finite element analysis were performed by Pro-Engineer, MSC/PATRAN, and MSC/NASTRAN, respectively.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.355-360
• /
• 2001

By using Frenet formulation and Timoshenko beam theory, the partial differential equations of motion are derived for a helical spring having a doubly symmetrical cross section subjected to the pre-load axially. These equations of motion are solved to give the dispersion relationship and dynamic stiffness matrix is assembled. Natural frequencies are obtained from the receptance of the system. The results of the dynamic stiffness method are compared with those of the transfer matrix method from published examples and finite element method.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(III)
• /
• pp.49-58
• /
• 2003

In this paper, the structural strengths of a rolling stock seat were numerically evaluated under several design load conditions based on the UIC requirements. The rolling stock seat was designed for the high speed train of a Chinese conventional line. To maximize its weight reduction and structural strength, some aluminium alloys like 6N01-T5 and ALDC8-T5 were applied to the base frame, side frame and armrest. The designed seat frame satisfied the strength requirements on inertia loads due to accelerations, and fatigue test conditions. However, it violated the requirements on the static test of UIC 566 OR. Some design modifications were suggested and numerically evaluated to satisfy the static test requirements.

• 대한조선학회논문집
• /
• 제45권3호
• /
• pp.322-328
• /
• 2008

Recently, the rapid progress of Internet and Network affects engineering design environment as well as Business fields to utilize Web technologies to enhance it's competitively in the world. In product development, experts and organizations actually taking part in the design process are often geographically dispersed. Furthermore, different divisions and businesses often have heterogeneous CAD/CAE systems and methods for expressing product data, and addressing this heterogeneity creates additional costs and causes longer development periods. To ensure successful collaboration in the design process, it is therefore imperative that distributed CAD, CAE, and other related systems be managed in an organic and integrated manner from the initial stages of product development. Therefore, this study suggests Web-based MDO(Multidisciplinary Design Optimization) framework to support interfacing and the collective use of design and analysis tools.

• 반도체디스플레이기술학회지
• /
• 제10권3호
• /
• pp.61-65
• /
• 2011

The capabilities of finite elements codes allow now accurate simulations of blanking processes when appropriate materials modelling are used. Over the last decade, numerous numerical studies have focused on the influence of process parameters such as punch-die clearance, tools geometry and friction on blanking force and blank profile. In this study, three dimensional finite element analysis is carried out to design a lead frame blanking die using LS-Dyna3D package. After design of the blanking die, an experiment is also carried out to investigate the characteristics of blanking for nickel alloy Alloy42, a kind of IC lead frame material. In this paper, it has been researched the investigation to examine the influence of process parameters such as clearance and air cylinder pressure on the accuracy of sheared plane. Through the experiment results, it is shown that the quality of sheared plane is less affected by clearance and air cylinder pressure.

• 한국수학교육학회지시리즈E:수학교육논문집
• /
• 제9권
• /
• pp.97-114
• /
• 1999

새로운 세기의 수학 교육은 직관과 조작 활동에 바탕을 둔 경험에서 수학적 형식, 관계, 개념, 원리 및 법칙 등을 이해하도록 지도되어야 한다. 즉 학생들의 내면 세계에서 적절한 경험을 통하여 시각적 ${\cdot}$ 직관적으로 수학적 개념을 재구성할 수 있도록 상황과 대상을 제공해야 한다. 이를 위하여 컴퓨터 응용 프로그램을 활용한 자기주도적 수학 개념 형성에 적합한 교수 ${\cdot}$ 학습 모델을 구안하여 보았다. 이는 수학의 필요성과 실용성 인식 및 자기주도적 문제해결력 향상을 위한 상호작용적 매체의 활용이 요구된다. 본 연구는 구성주의적 수학 교수 ${\cdot}$ 학습 이론을 근간으로 대수 ${\cdot}$ 해석 ${\cdot}$ 기하 및 스프레트시트의 상호 연계를 통하여 수학 지식을 재구성할 수 있도록 학습수행지를 제작하여 교사와 학생의 다원적 상호 학습 기회를 제공하는 데 주안점을 두고자 한다.