• Korean Journal of Materials Research
• /
• v.6 no.4
• /
• pp.428-435
• /
• 1996

초미립 SiC분말과 SiC platelet을 2차성으로 Si3N4에 첨가하여 SiC/Si3N4 하이브리드 복합체를 가압소결로 제조한 후 2차상의 영향을 조사한 결과핫프레스법을 이용한 경우 SiC platelet은 Si3N4 기지 복합채의 치밀화를 저해하지 않고 초미립의 SiC 첨가는 Si3N4의 입성장을 효과적으로 억제하여 미세한 $\beta$-Si3N4의 grain을 형성함을 관찰하였다. 초미립 SiC첨가를 통한 복합체의 강도 증진은 상대적으로 $\beta$-Si3N4입자의 미세화에 의한 인성의 저하를 유도하나 SiC platelet을 첨가하여 급격한 강도 저하 없이 높은 인성을 갖는 하이브리드 복합체를 제조할 수 있었으며 SiC/Si3N4 하이브리드 복합체의 인성증진은 elongated $\beta$-Si3N4와 platelet SiC의 debonding에 의한 grain pull-out 영향임을 알 수 있었다.

• Proceedings of the KAIS Fall Conference
• /
• 2008.05a
• /
• pp.46-48
• /
• 2008

나노복합 블레이드가 반도체 웨이퍼 가공을 위한 마이크로급 나노장치나 그 이상의 나노급 구조체를 위해 사용되었다. 금속 블레이드는 실리콘 웨이퍼 가공을 위해 사용되어 왔다. 그러나, 최근 레진 복합 블레이드는 반도체나 핸드폰의 쿼츠 웨이퍼 가공에 사용된다. 유기 또는 비유기 재료 선정은 기계가공성, 전기 전도성, 강도, 연성 및 웨이퍼 저항을 가진 블레이드를 만드는데 중요하다. 고성능 응용의 증대 요구에 따라 개발된 고기술 비유기성 재료의 혼합은 낮은 가격에 고기능의 신뢰도를 필요로 한다. 나노 입자의 크기를 가진 레진 복합물의 마이크로 설계는 입자간 상호작용의 제어가 필요하다. 형상 제작 동안 마이크로 차원에 두께를 유지하기 위해서는 마이크로/나노급 제작을 위한 가공기술이 중요한 것 중의 하나이다. 본 연구에서는 핫 프레스 구조물이 원래 설계 기준과 두께 차이의 실험 접근법을 사용해 만들어졌다. 다른 습식 공정 기술은 차원의 허용치를 개선하기 위해 만들었다. 실험들과 해석들은 신뢰성 결과가 사용가능함을 보여주었다. 반도체 시장에 사용될 레진 복합 블레이드의 개선 효과가 논의되었다.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.347-351
• /
• 2004

[ $Si_3N_4$ ] composites have been extensively studied for engineering ceramics, because it has excellent room and high temperature strength, wear resistance properties, good resistance to oxidation, and good thermal and chemical stability. In the present work, carbon short fiber reinforced $Si_3N_4$ ceramics were fabricated by hot press method in $N_2$ atmosphere at $1800^{\circ}C$ using $Al_2O_3\;and\;Y_2O_3$ as sintering additives. Content of carbon short fiber was $0\%,\;0.1\%\;and\;0.3\%$. The composites were evaluated in terms of density, flexural strength and elastic modulus through the 3-point bending test at room temperature. Also, The wear behavior was determined by the pin on disk wear tester using silicon nitride ball. Experimental density and flexural strength decreased with increasing content of carbon fiber. But specific modulus increased with increasing content of carbon fiber. In addition, friction coefficient and specific wear loss decreased with increasing content of carbon short fiber by reason of interfacial defects between matrix and fiber.

• Composites Research
• /
• v.25 no.5
• /
• pp.154-158
• /
• 2012

The effect of structure on the sound absorption and sound transmission loss of composite sheet was investigated. A sheet of polypropylene was bonded by hot press with nonwoven fabric sheets of polyethylene terephthalate on the top side and the back side. Absorption coefficient of composite sheet using nonwoven fabric with surface density of $0.64kg/m^2$ was 0.1-0.2. It is 100-400% improvement compare to that of polypropylene sheet. The transmission loss of composite sheet was increased with surface density of polypropylene board and introduction of hemisphere hole on the surface of sheet. Two types of composite sheet were made using flat sheet and sine wave shaped sheet and the effect of sheet structure on the transmission loss was investigated.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.11a
• /
• pp.266-270
• /
• 2004

SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine because it has excellent high temperature strength, low coefficient of thermal expansion, good resistance to oxidation and good thermal and chemical stability etc. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, SiC/SiC composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing jiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of SiC/SiC composites by hot pressing method. In the present work, monolithic Liquid Phase Sintered SiC (LPS-SiC) was fabricated by hot pressing method in Ar atmosphere at $1800^{\circ}C$ under 20MPa using $Al_2O_3,\;Y_2O_3\;and\;SiO_2$ as sintering additives in order to low sintering temperature and sintering pressure. The starting powder was high purity $\beta-SiC$ nano-powder with all average particle size of 30mm. The characterization of LPS-SiC was investigated by means of SEM and three point bending test. Base on the composition of sintering additives-, microstructure- and mechanical property correlation, tire compositions of sintering additives are discussed.