• 한국정밀공학회지
• /
• 제18권4호
• /
• pp.9-18
• /
• 2001

• 한국정밀공학회지
• /
• 제19권8호
• /
• pp.26-33
• /
• 2002

• 소음진동
• /
• 제7권3호
• /
• pp.354-361
• /
• 1997

본 글에서는 HDD에 관련된 기술 중 기계적 요소와 관련된 내용을 소개하는데 중점을 두었다. HDD의 기본 요소들을 2절에서 간략히 소개하고 3절에서는 동역학.서보 기술을 기술하였다. 4절에서는 HDD의 진동과 충격에 관련된 문제와 기술적 사항을 설명하였다. 그리고 마지막으로 장래 기술전망에 대해 간략하게 기술하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.216-217
• /
• 2009

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.508-509
• /
• 2012

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1998년도 춘계학술대회논문집; 용평리조트 타워콘도, 21-22 May 1998
• /
• pp.233-237
• /
• 1998

In this work, to identify the dynamic characteristics of disk-spindle system in hard disk drive, experimental modal analysis was performed. And an experimental analysis system including testing apparatus, precision sensors, and analysis software was established in order to perform the testing effectively. From the experimental results, coupled and uncoupled modal characteristics of 3-disk spindle system are clearly identified.

• 한국자기학회지
• /
• 제7권2호
• /
• pp.97-102
• /
• 1997

자기헤드의 오프트랙 성능은 하드디스크 드라이브에서 트랙 피치를 결정하는데 사용되고 오프트랙 성능이 트랙 피치에 관한 함수가 747 곡선이다. 본 논문에서는 747 곡선을 컴퓨터를 이용하여 시뮬레이션 하였다. 헤드의 측면재생과 기록변수는 3차원 유한요소법을 이용한 자장해석을 이용하여 구하였고, 신호대 잡음비 (signal to noise ratio : SNR) 계산을 위한 헤드의 재생 신호와 잡음은 가역정리를 이용하여 구하였다. 생성된 747 곡선에 의하면, 소거밴드의 폭이 클수록 또한 유효 신호대 잡음비 SNR$_{eff}$이 작을 수록 오프트랙의 성능이 향상되었다. 기록된 트랙폭이 4.1 .mu. m 인 평면 실리콘 헤드를 사용하여 시뮬레이션으로 생성된 747 곡선과 스핀 스탠드 (spin stand)로 측정된 747 곡선을 비교했을 때, 두 곡선이 비슷하였으며 이로부터 본 시뮬레이션의 타당성을 입증할 수 있었다.다.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.87-95
• /
• 2005

This paper proposes a method to calculate the characteristics of a coupled hydrodynamic journal and thrust bearing of a HDD spindle motor. The governing equations for the journal and thrust bearings are the two dimensional Reynolds equations in $\theta z$ and $ r\theta$ planes, respectively. Finite element method is appropriately applied to analyze the coupled journal and thrust bearing by satisfying the continuity of mass and pressure at the interface between the journal and thrust bearings. The pressure in a coupled bearing is calculated by applying the Reynolds boundary condition and compared with that by using the Half-Sommerfeld boundary condition. The static characteristics are obtained by integrating the pressure along the fluid film. The flying height of spindle motor is measured to verify the proposed analytical result. This research shows that the proposed method can describe HDB in a HDD system more accurately and realistically than the separate analysis of a journal or thrust bearing.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.75-80
• /
• 2006

This paper introduces the mechanism of the ESD(electrostatic discharge) in the HDD spindle system using FDBs(fluid dynamic bearings). When a HDD(hard disk drive) spindle system is rotating, triboelectric charging occurs in the FDBs through the friction between the lubricant and the rotating shaft or between the lubricant and stationary sleeve. And this electrostatic charge is accumulated in the rotating parts of the HDD spindle system because they are insulated from the ground by the lubricant. This research shows experimentally that the behavior of electric charge and discharge in the FDB spindle system is the same as that of a capacitor. It also measures the electrostatic voltage difference between the rotating and stationary parts in the FDB spindle system due to the change of humidity, supporting load and motor speed. This research shows that the control of ESD is required in the HDD spindle system using FDBs, because the electrostatic charge accumulated in the FDB spindle system may cause the breakdown damage of the GMR head and data loss consequently.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.50-56
• /
• 2006

Since most of small form-factor drives have a load/unload mechanism and the flying height of the head is getting lower as the capacity of disk drives increases, the load/unload velocity becomes one of the important factors to ensure the reliability of the load/unload mechanism. To control the load/unload velocity accurately, velocity sensing is essential. In this paper, we introduce a very practical method that acquires the load/unload velocity from the back electromotive force (BEMF) of a voice coil motor (VCM) and propose a calibration method for measuring the BEMF from a given circuit. Moreover, the effect of calibration error and temperature variation on the measurement of BEMF is shown by simulation. Then, this present method is applied to the load/unload velocity controller and is verified from the experimental result.