• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.205-205
• /
• 2012

Korea Superconducting Tokamak Advanced Research (KSTAR) 장치는 국내 유일의 초전도 자석을 이용한 핵융합 연구 장치로서 초고온의 플라즈마를 생성하여 차세대 에너지원인 핵융합 에너지를 획득하는 것을 목표로 두고 있다. 플라즈마를 생성부터 유지하기 위해서는 수소 동위원소를 토카막 내부로 공급해 주어야 하는데 이러한 수소동위원소를 "연료"라 부르며, 이 연료를 토카막 내부로 공급해 주는 시스템을 연료주입 시스템(Fueling System)이라고 한다. KSTAR에서는 토카막 내부로 고속의 연료 주입이 필요하고 정밀한 양의 연료를 공급하는 밸브를 사용하여야 하며, 이러한 밸브를 제어 할 수 있는 제어기를 필요로 한다. 위의 사항에 적합한 피에조 밸브(Piezoelectric Valve)는 2 msec 이내의 개폐시간과 500 Torr ${\ell}$/s 이상의 유량을 흘려줄 수 있는 피에조 밸브로 압전소자에 가해지는 전압(0~250 V)에 따라 변위의 양에 비례하여 연료가 진공용기 내로 유입된다. 압전소자의 변위는 최대 140 ${\mu}m$로 최적화되어 있어야 하며, 정전용량(Capacitance)는 30~40 nF이어야 한다. 또한 소자에 힘(Force)를 가해 최대 7 N으로 136 ${\mu}m$의 변위를 가진 소자를 사용해야 한다. 피에조 밸브의 특성으로는 아날로그 신호로 작동이 되어야 하며, 유량신호를 피드백하여 밸브의 구동 전압을 정밀하게 제어 되어야 한다. 피드백 제어를 위해 압력센서는 XCS-190 Series를 사용하여 낮은 유량에서도 민감하게 반응하도록 제작하였으며, 고전압이 유기 되었을 때 제어기를 보호하기 위한 정션박스를 설치하였다. 밸브 제어기는 피에조 밸브의 개방 속도를 높이기 위해 밸브 구동 전압을 순간적으로 높이는 POP 전압을 생성하는 기능과 유량 신호를 피드백해서 밸브 구동 전압을 정밀 제어 하는 기능을 가지고 있다. 제어장치는 아날로그 및 디지털 제어회로의 전원용 +15 V DC와 밸브 구동용 +250 V DC 출력용의 전원 공급 장치(Power supply unit), 펄스 및 트리거 신호를 생성하는 Master Programmer unit), Pop 전압과 피드백의 중요한 기능을 수행하는 Valve controller unit로 제작 되었다. 피에조 밸브와 제어기는 상호 작용하여 동작을 원활히 할 수 있도록 특성 실험을 진행하여야 하며, 진공상태에서 Lack의 유무를 확인하여야 한다. 현재 개발 제작된 밸브의 진공누설시험 및 특성실험을 진행하고 있으며, KSTAR 5차 캠페인에 적용할 계획이다.

• 한국ITS학회:학술대회논문집
• /
• 2003.11a
• /
• pp.56-61
• /
• 2003

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.6
• /
• pp.509-523
• /
• 2023

The high-level nuclear waste (HLW) repository is exposed to complex environmental conditions consisting of high temperature, high humidity, and radiation, resulting in structural deterioration. Therefore, structural health monitoring is essential, and piezo sensors are used to detect cracks and estimate strength. However, since the monitoring sensors installed in the disposal tunnel and disposal container cannot be replaced or removed, the quantitative life of the monitoring sensor and its suitability must be assessed. In this study, the life of a piezo sensor for monitoring was assessed using an accelerated life test (ALT). The failure mode and mechanism of the piezo sensor under high temperature conditions were determined, and temperature stress's influence on the piezo sensor's life was analyzed. ALT was conducted on temperature stress and the relationship between temperature stress and piezo sensor life was suggested. The life of the piezo sensor was assessed using the Weibull probability distribution and the Arrhenius acceleration model. The suggested relationship can be used in multiple stress ALT designs for more precise life assessment.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3191-3196
• /
• 2013

Ultrasonic transducer is the sensor which is measuring distance. Piezo ceramic of ultrasonic sensor and adhesive technique of matching layer are the most core techniques. With the study of relation on matching layer which takes off the ultrasonic wave into the air, this paper aims to find the second useful frequency as the results which can be changed are extracted in case piezo ceramic and matching layer are bonded. And the experiment is done with piezo ceramic as real piezoelectric element and matching layer of chemical wood. OD of piezo ceramic has designed by ${\Phi}50{\times}3T$ and OD of matching layer is designed by ${\Phi}62{\times}12t$ with ${\lambda}=1/4$. Acoustic impedance is generated at the most optimum resonant frequency of 53 Khz. As experimental result, more available frequency can be generated by using the adhesive close to solid than the flexible one.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.181-187
• /
• 2013

Performance of DI diesel engine with high fuel injection method is directly related to its emission characteristics and fuel consumption. In this study, numerical model of 3rd generation piezo-driven injector was designed to analyze the hydraulic performance. Also the injection response characteristics was investigated by using the AMESim simulation code. From this study, it was shown that 3rd generation piezo-driven injector had a faster response and had better control capability due to its hydraulic bypass-circuit that has potential to higher hydraulic characteristics and improved accuracy of injected fuel quantity.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.4 s.121
• /
• pp.333-341
• /
• 2007

Waveform design method for inkjet printing has been proposed tv pressure wave measurement. The pressure wane inside the inkjet dispenser can be effectively measured by current measurement due to self-sensing capability of PZT. The pressure wave measured from current was verified by commercially availablelaser vibrometer. In order to obtain high speed inkjet droplets, two pulse waveform was designed such that the pressure wane after droplet formation can be minimized.

• Journal of ILASS-Korea
• /
• v.25 no.1
• /
• pp.1-7
• /
• 2020

In the common rail fuel injection system, which is the core of diesel high efficiency and NO_X reduction, injection strategies such as high pressure injection of fuel, accurate injection rate control, and multistage injection are important to increase fuel atomization. In this study, the bypass type piezo injector for the electronic control based common rail injection system applied to diesel fuel vehicle was studied. In particular, the injection rate and internal fuel flow characteristics of the high-pressure injector according to the piezo stacking number and applied voltage were analyzed by theoretical numerical method. When the applied voltage changes, it is determined that additional fuel flow through the bypass compensates for the reduced valve driving force due to the change in the driving voltage.

• The Journal of Engineering Geology
• /
• v.21 no.4
• /
• pp.349-359
• /
• 2011

The consolidation behavior of soft clay is controlled mainly by its compressibility and deformation characteristics. Soil permeability depends on various soil characteristics, including the soil type and anisotropy. The coefficient of permeability of soft clay is determined by using a laboratory test (the Oedometer test) or a piezocone test. The latter test is useful for estimating the permeability characteristics from $c_h$ and $k_h$ by performing an excess pore-pressure dissipation test. This study seeks to validate an existing theoretical formula in applying it to marine clay, and to assess the relation between $k_h/k_c$ and the mechanical properties of soft clay. Piezocone tests and laboratory tests were performed using sediment from the Yellow Sea and from the South Sea near Korea. We compared $k_h/k_v$ values obtained using the piezocone test and using laboratory consolidation tests. The obtained values are similar to the values obtained by Jamiolkowski et al. (M application); therefore, the latter values are recommended to be used as $k_h/k_v$.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.4
• /
• pp.47-55
• /
• 2007

Using the results of the Piezocone Penetration Test (PCPT) which were executed at the Yangsan-Mulgum site, the applicability of the interpretation methods for estimating the coefficient of consolidation ($C_v$) of soft clay was evaluated. At the same time, laboratory soil tests using the total of 172 undisturbed soft clay samples from the 44 regions of the Yangsan-Mulgum site were performed to study the differency in the coefficient of consolidation ($C_v$) compared to the results of PCPT. The calculated constrained modulus ($M_{\varepsilon}$) and coefficient of consolidation ($C_v$) using the results of consolidation laboratory tests which are based upon the consolidation theory of Terzaghi were compared with the predicted constrained modulus ($M_p$) and coefficient of consolidation ($C_{v-{M_p}}$) from the PCPT. The relationship between the predicted constrained modulus ($M_p$) and the calculated constrained modulus($M_c$) were showed good correlation. The $M_p$ by the Jones & Rust method were showed mostly similar to the calculated constrained modulus ($M_c$). The relationship between the coefficient of consolidation ($C_v$) obtained from the consolidation tests and the calculated coefficient of consolidation ($C_{v-{M_p}}$) were showed a linear relationship. The results of the calculated coefficient of consolidation ($C_{v-{M_p}}$) were about 54% of the value of the coefficient of consolidation ($C_v$) obtained from the consolidation tests.

• Proceedings of the KAIS Fall Conference
• /
• 2011.05b
• /
• pp.828-831
• /
• 2011

본 논문에서는 피에조 잉크젯 헤드의 액적 토출 형상에 대해 전산해석을 통하여 연구하였다. 열유체 해석 전용 프로그램인 FLUENT를 이용하여 에틸렌 글리콜이 잉크젯 헤드의 노즐에서 토출될 때의 형상을 전산모사하였다. 노즐 출구에서 메니스커스 변위의 시간에 따른 변화를 직접 측정하여 노즐 입구의 속도분포를 예측하고 이를 해석의 입력 자료로 사용하였다. 측정치와 해석치를 비교한 결과 전산해석이 측정치의 액정 형성 과정을 잘 모사함을 알 수 있었다.