• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 2000.06a
• /
• pp.31-36
• /
• 2000

평면연삭은 기계부품의 후가공 공정에 사용되며, 기계부품의 다듬질면은 내마멸성, 피로강도 및 내식성등 품질에 큰 영향을 미친다. 연삭작업중 가장 큰 위험 요소는 고속작업중 연삭숫돌의 파손이다. 연삭숫돌의 파괴되는 주요 원인은 고속 회전중 최고사용 원주속도를 넘어 지나치게 빠를 때 원심력이 결합력보다 커지는 경우와, 숫돌에 균열(crack)이 있을 때이다. 연삭숫돌이 파괴되어 숫돌 파편이 작업자의 머리, 안면등을 강타하여 사망이나 골절등 중대재해가 발생된다. (중략)

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1995.06a
• /
• pp.25-30
• /
• 1995

본 연구에서는 건식 구름접촉시 발생하는 tribological한 현상들을 plate on ball tester를 이용하여 실험적으로 고찰하였다. 실험의 주된 관심은 각 열처리 방법으로 제작한 시편에 대하여 건식 구름접촉시 cycle수에 따른 plate의 표면 거칠기, 트랙의 형상, 졍도 및 구름저항의 변화이며 이런 자료를 토대로 열처리공정의 차이에서 오는 정도수명 및 피로수명에 대한 상대평가를 통해 마찰, 마멸의 저감에 적합한 열처리방법을 제시하고자 한다.

• Tribology and Lubricants
• /
• v.30 no.4
• /
• pp.199-204
• /
• 2014

Various heat-treated and surface coating methods are used to mitigate abrasion in sliding machine parts. The most cost effective of these methods involves hard coatings such as diamond-like carbon (DLC). DLC has various advantages, including a high level of hardness, low coefficient of friction, and low wear rate. In practice, a supporting layer is generally inserted between the DLC layer and the steel substrate to improve the load carrying capacity. In this study, an indentation and sliding contact problem involving a small, hard, spherical particle and a DLC-coated steel surface is modeled and analyzed using a nonlinear finite element code, MARC, to investigate the influence of the supporting layer thickness on the coating characteristics and the related coating failure mechanisms. The results show that the amount of plastic deformation and the maximum principal stress decrease with an increase in the supporting layer thickness. However, the probability of the high tensile stress within the coating layer causing a crack is greatly increased. Therefore, in the case of DLC coating with a supporting layer, fatigue wear can be another important cause of coating layer failure, together with the generally well-known abrasive wear.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2019-2028
• /
• 1997

It has been well established that resistant force and wear that occur during rolling motion depend on several factors such as material type, hardness, subsurface microstructure, applied load, and speed. The purpose of this work is to investigate the effect of microstructure and the state of deformed layer on the rolling contact characteristics in dry and lubricated rolling contacts. The results of this work show that the rolling resistance behavior depends on the state of the deformed layer. Also, lubrication can reduce the plastic flow at the surface but may still have an effect on the subsurface strain. The cross-sectional view of the microstructure shows that surface traction has a difinite effect on the morphology of the surface region. That is, significant slip seems to have taken place between the ball than those of the dry rolling case. The surface generation effects were significantly less compared to the case of dry rolling contact.

• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.225-230
• /
• 2009

Seals are very useful machine components in protection of leakage of lubricant or working fluid, and incoming of debris from outside. Various elastomer are widely used as sealing materials and the shaft surfaces are generally coated with high hardness material after heat treatment. It is generally known that the foreign debris and wear particles get stuck into sealing surface, the steel shaft surface can be damaged and worn by mainly abrasive wear. In this paper, using MARC, contact analysis are conducted to show the hard coated steel shaft surface can be fatigue failed by very small elastic particle intervened between seal and steel surface. Variations of contact and von-Mises stress distributions and contact half-widths with interference and coating thickness are presented. The maximum von-Mises stress occurs always in the coating layer or between coated layer/substrate interface. Therefore the coated sealing surface can be fatigued and then failed by very small particles. The results can be used in design of sealing surface and further studies are required.

• Tribology and Lubricants
• /
• v.10 no.2
• /
• pp.51-55
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1810-1815
• /
• 2000

발전기 회전자와 고정자 사이에 유기되는 전자력은 발전기 운전중 진동 피로 현상을 유발시켜 발전기 수명 저감의 요인이 된다. 특히 고정자 코어부에 비해 기계적 구속력이 비교적 약한 권선 단말부에서의 진동은 냉각수 누수, 권선 마멸등에 의한 2차 사고를 유발시킬수 있다. 따라서 본 논문에서는 국내 발전소에서 운전중인 발전기를 중심으로 수행한 제작사별 고정자 권선의 진동 특성을 비교 분석하였다.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.71-77
• /
• 1994

Rolling friction test was carried out to investigate the effect of the wear amount on rolling contact fatigue process in lubrication oil. The methods of this process were conducted at two Hertzian contact pressure and three slide ratio in each case by employing normalized and annealed carbon steel. During process of the rolling contact fatigue, the number of rotation until surface damage was occurred, the wear amount of rolling contact surface, and residual stress and half-value breadth using X-ray reflection on rolling contact surface were investigated. The result of this study shows that rolling contact fatigue process was directly influenced by wear trend and was confirmed by change of residual stress and half-value breadth on rolling contact surface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1587-1590
• /
• 2005

A rigid-plastic finite element analysis for the die forging process of a socket ball joint, which is used in the transportation system, was carried out. And also with the results, the elastic stress analysis for the forging die was performed in order to get basic data for the die life prediction. The die fatigue life prediction was simulated using Goodman's and Gerber's equation. The prediction technique for the fatigue life of a forged product, the socket ball joint, using DEFORM-3D is presented and the results are commented upon. Archard's wear model was used for the wear simulation and then the wear simulation and then the wear quantity was quantity was evaluated using volume. In order to prove the wear simulation results to be reliable, wear quantity of the real forging die set in used a forging factory was measured using a 3-dimensional measurement apparatus. The simulation results were relatively in good agreement with the experimental measurements.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.4
• /
• pp.583-594
• /
• 1989

The strong nonliner dynamic behavior of mechanical systems in the presence of clearances are studied. The nonlinearity is induced from the assumed symmetric piecewise-linear characteristics for stiffness and damping by the contact and uncontact. Based on Stoker's assertion concering the reasoning beyond the occurrence of subharmonics, the nonlinear differential equation is converted to four nonlinear algebraic equations form the boundary conditions at the contact points. For a single contact per half exciting period, under the assumption of symmetric response, the steady-state solutions obtained are in agreement with those of numerical integration. Also a nondimen-sionalized formulation is made for the purpose of parametric studies.