• Korean Journal of Optics and Photonics
• /
• v.24 no.5
• /
• pp.213-216
• /
• 2013

This paper presents a combination of linear Fresnel lenses optimized for ${\times}25$ solar concentration. The combined lens consists of $5{\times}5$ linear Fresnel lenses. Each Fresnel lens is of $10{\times}10$ mm and optimized to tilt the incoming light onto a solar cell of the same size. All of the optimized Fresnel segments have the same pattern height of 35 ${\mu}m$, draft angle of $4^{\circ}$, and edge groove round of 1 ${\mu}m$ but with different facet angles varying from $14.1^{\circ}$ to $31.2^{\circ}$. The solar concentrating efficiency of the combination is shown to be over 80% and more robust than a conventional single ${\times}25$ circular Fresnel lens in terms of pointing misalignment and manufacturing errors. A sensitivity analysis finds that the edge groove round should be kept as small as machining allows since the concentrating efficiency drops ~5% per 1 ${\mu}m$ increase of the edge groove.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.53-56
• /
• 2009

반사와 굴절이 합쳐진 새로운 형태의 하이브리드 태양광 집광 장치로 기존 집광 장치에 비해 초점 거리가 짧게 설계되었다. 프레넬 렌즈 형태의 굴절부와 프레넬형의 다수의 포물선 반사경이 공통으로 후면 초점(rear focus)을 가지도록 배치하여 기존 프레넬 렌즈만으로 구성된 것보다 선형 집광의 경우는 3배, 점 집광의 경우는 10배 이상 집광비를 높일 수 있다.아울려 이를 이용한 선형 집광형 발전 시스템과 점형 집광 장치는 나름대로 장점을 가진다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.53-54
• /
• 2014

By using geometrical structure of Fresnel lens, it can be applied with receiver antenna and geodetic system. In this paper, radiation pattern from fresnel lens array of Soret type is calculate by the FDTD method. For simplicity, fresnel lens should be located linearly and considered to be dielectric rod with a relative permittivity.

• Korean Journal of Optics and Photonics
• /
• v.32 no.1
• /
• pp.15-21
• /
• 2021

In this paper, an aircraft warning light's optical system was designed using an LED light-source module and a collimating Fresnel lens. As for the optical system, a collimator Fresnel lens was designed for each module to satisfy a vertical-elevation center luminous intensity of 20,000 cd and the divergence-angle luminous-intensity standard conditions of the Ministry of Land for Infrastructure and Transport for aircraft warning lights. In addition, the optical system was optimized by adjusting the position and tilt of the LED light-source module and Fresnel lens. By analyzing and comparing the light-distribution characteristics of the optical system, an aircraft-warning-light optical system with optimal performance was obtained.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.5
• /
• pp.1-6
• /
• 2008

LCD multimedia system is necessary to display and transfer the effective image informations. However, this system uses several LCD screens, so the problem of gap between the LCD screens occurs. In order to solve this problem, this paper presents a method of using binary Fresnel lens. This kind of binary fresnel lens makes each screen enlarge and minimize the gap. The optimization of design parameters of binary Fresnel lens is presented.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.43-44
• /
• 2014

By using geometrical structure of Fresnel lens, it can be applied with receiver antenna and geodetic system. In this paper, we consider Soret typed fresnel lens with reflected plate and its focusing gain characteristics is calculated by the FDTD method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.1
• /
• pp.63-67
• /
• 2015

White light-emitting diode (WLED) is growing interest in using both illumination and communications. This paper reports visible light communication (VLC) composed of a super bright white light-emitting diode, low cost commercial photo-diode and a Fresnel lens. LED driver is consisted of the power MOSFET and MOSFET driver that switches the LED on and off. The modulation bandwidth of the LED used was determined to be 8 MHz. However, it was possible to communicate up to 1 Mbps under illumination of 500 lx because of the weak signal power and a low spectral sensitivity of the SHF213 as a PIN photodiode. In order to enhance the system bandwidth, the LED light was focused on the PIN photodiode by use of the Fresnel lens. As a result of that, visible light link was operated up to modulation bandwidth of the LED. The signal to noise ratio can be improved by 40 dB using an optical concentration at the receiver.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.67-69
• /
• 2012

In this paper, electromagnetic scattering analysis of Fresnel Lens by using 2D FDTD method was performed. Fresnel lens which is consigured 7 diffracted conductors, and considered at 5GHz. As a result, axial gain characteristic corresponding to near design focusing distance at 0.71m is 26dB.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.2
• /
• pp.1-7
• /
• 2006

A light guided plate coupled with the micro Fresnel lens array(MFTA) is designed to improve the efficiency of the LCD backlight unit. Blazed Frenel lens and binary multi-level Fresnel lens are adapted for the MFLA. This type of MFLA can replace the prism sheet and diffuser sheet which are used for the conventional type of the LCD backlight unit. The luminance and uniformity are calculated to verify the performance of the MFLA type LCD backlight unit.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2022.11a
• /
• pp.28-30
• /
• 2022

종래의 프레넬렌즈가 회전하는 중대형 회전식 등명기는 고압방전등(메탈할라이드) 전구를 광원으로 사용하고 있으나, 에너지효율, 수은 등의 함유로 인한 환경오염과 폐기 문제로 인해 2010년 초에서 현재에 이르기까지 선진국을 중심으로 사용규제가 강화되고 있는 실정이다. 국내에 설치 운영되고 있는 회전식 등명기는 내용연수 초과 혹은 도래시기 점차 다가오고 있기 때문에 이에 대한 대응 방안이 필수적인 상황이다. 프레넬렌즈를 회전시키는 회전식 등명기의 LED 광원 개발은 2010년 초부터 해외업체에서 제품출시가 이루어졌으나 국내 중대형 회전식 등명기에 적용된 사례는 없으며 국내에서도 해당 기술 미비로 개발된 사례가 없었다. 이에 본 연구를 통해 단일 고출력 COB LED, 리플렉터, 집광렌즈 등을 이용한 가상초점광원 구현 기술로 회전식 등명기용 LED 광원 연구를 수행하고 해당 연구기술이 적용된 시제품 제작을 통해 성능을 검증하였다.