• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.9
• /
• pp.499-504
• /
• 2015

The composite anodes of expanded graphite (EG) and multiwall carbon nanotube (MWCNT) for microbial fuel cells were fabricated by using coal tar pitch (CTP) binder containing nickel (Ni), and the effect of the anodes with the binders on the performance of the MFCs were examined in a batch reactor. During the start-up of the MFCs, quick increase in voltage was observed after a short lag phase time, indicating that the CTP binder is biocompatible. The biomass attatched on the anode surface was more at higher Ni content in the binder, as well as at smaller amount of CTP binder for the fabrication of the anode. The internal resistance of the MFC was smaller for the anode with more biomass. Based on the results, the ideal combination of CTP and Ni for the CTP binder for anode was 2 g and 0.2 g, respectively. The maximum power density was $731.8mW/m^2$, which was higher 23.7% than the anode with Nafion binder as control. The CTP binder containing Ni for the fabrication of anode is a good alternative in terms of performance and economics of MFCs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.66.1-66.1
• /
• 2011

반도체를 비롯하여 LCD, OLED와 같은 디스플레이 (FPD: Flat Panel Display) 분야는 국가 선도 사업으로써 발전을 거듭해오고 있다. 하지만 기술의 성숙도가 높아짐에 따라 최근 중국과 대만 업체와의 경쟁이 심화되고 있으며, 더불어 환경문제가 큰 이슈로 떠오르고 있어 신기술 개발을 통한 생산 수율 향상 및 친환경 공정 개발의 중요성이 커지고 있다. 반도체, 디스플레이 공정에서 생산 수율 저하의 주요 원인으로써 공정 중 발생하는 미세 오염 입자를 들수 있다. 반도체 및 디스플레이 공정에서 세정 기술은 전체 기술의 30% 이상을 차지하며 생산 수율 및 제품의 품질에도 큰 영향을 주는 공정이다. 세정 공정은 일반적으로 습식 세정 공정이 낮은 공정비용을 바탕으로 널리 적용되어 왔으나, 기판의 대형화와 패턴의 미세화에 따라 정밀한 세정 스펙이 요구되며 더불어 막대한 양의 초순수와 화학액의 사용으로 인한 공정비용 증가와 환경 규제 강화에 따른 폐수 처리의 문제에 직면하고 있다. 이에 따라 폐수의 양을 줄이며 건조공정을 필요로 하지 않아 공정비용을 줄일 수 있는 건식 세정 공정에 대한 연구가 활발히 진행 되고 있다. $CO_2$ snow jet 세정 기술은 건식 공정으로써 $CO_2$ 가스를 특수하게 제작된 분사 노즐에서 고압으로 가스를 분사하여 이 때 발생되는 순간적인 감압에 의한 단열 팽창으로 생성된 $CO_2$ snow 입자가 기판 표면의 오염물과 물리적 충돌을 하어 세정이 이루어지는 기술이다. 특히 $CO_2$ 세정은 환경과 인체에 무해하며 공정 후 바로 승화하기 때문에 추가적인 폐수처리 공정 등이 필요하지 않고, 건식 공정으로써 수세(Rinse) 공정을 필요로 하지 않기 때문에, 공정비용을 크게 줄일 수 있으며 물반점 발생을 방지 할 수 있는 친환경 건식 공정으로써의 장점을 가지고 있다. 본 연구에서는 자체적으로 개발한 $CO_2$ snow jet을 바탕으로 하여 다양한 공정조건을 변화시켜 세정효율을 측정하는 한편, 최적화 하기 위한 연구를 진행하였으며 더불어 $CO_2$ snow의 세정력을 정량적으로 평가하기 위한 연구를 진행하였다. 실험을 통해 가장 효과적으로 $CO_2$ snow 입자를 배출 할 수 있는 공정 조건으로써 5 bar의 캐리어 가스 압력을 사용하여, 세정력에 가장 큰 영향을 줄 수 있는 분사 노즐과 기판 사이의 거리 및 분사 노즐의 각도 등을 변화시켜 각 조건에 따른 세정효율을 평가하였다. 세정 오염물은 Silica, PSL 표준 입자(Duke scientific, USA)를 정량적으로 웨이퍼에 오염 시킨 후, 파티클 스캐너(Surfscan 6500, KLA-Tencor, USA)를 이용하여 세정 전 후의 오염입자 개수 변화를 통해 정량적으로 세정효율을 평가하였다. 본 연구를 통하여 $CO_2$ snow jet를 이용한 친환경 고효율 건식 세정 공정 메커니즘을 분석하였으며, 노즐과 기판 사이의 간격 및 분사 노즐의 각도 등을 최적화 한 세정 공정을 얻을 수 있었다.

• Journal of the Korean Vacuum Society
• /
• v.11 no.1
• /
• pp.50-58
• /
• 2002

The growth of GaN films on Si substrate has many advantages in that Si is less expensive than sapphire substrate and that integration of GaN-based devices with Si substrate is easier The difference of lattice constant and thermal expansion coefficient between GaN and Si is larger than those between GaN and sapphire. However, which results in many defects into the grown GaN. In order to obtain high duality GaN films on Si substrate, we need to reduce defects using the buffer layer such as AlN. In this study, we prepared three types of AlN buffer layer with various crystallinity on Si (111) substrate using MOCVD, Sputtering and MOMBE methods. GaN was grown by MOCVD on three types of AlN/Si substrate. Using TEM and XRD, we carried out comparative investigation of growth and properties of GaN deposited on the various AlN buffers by characterizing lattice coherency, crystallinity, growth orientation and defects formed (voids, stacking faults, dislocations, etc). It is found that the crystallinity of AlN buffer layer has strong effects on growth of GaN. The AlN buffer layers grown by MOCVD and MOMBE showed the reduction of out-of-plane misorientation of GaN at the initial growth stage.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.3
• /
• pp.116-120
• /
• 2015

$La_2NiO_{4+{\delta}}$ based oxides, a mixed electronic-ionic conductors (MIECs) with $K_2NiF_4$ type structure, have been considerably investigated in recent decades as electrode materials for advanced solid oxide fuel cells (SOFCs) due to their high electrical conductivity, and oxidation reduction reaction (ORR). In this study, structure properties of $La(Ca)_2Ni(Cu)O_{4+{\delta}}$ were studied as a potential cathode for intermediate temperature SOFCs (IT-SOFCs).

• Korean Journal of Ichthyology
• /
• v.8 no.1
• /
• pp.83-89
• /
• 1996

The early life history of Korean bullhead, Pseudobagrus fulvidraco was studied to obtain some information required in aquaculture and reinforcement of natural population. The fertilized eggs were almost spherical in shape and demersal. The egg membranes were transparent with minute folds on the surface, causing them to stick to other substrates. Yolk is yellowish without oil droplets. The eggs just after fertilization were measuring $1.4{\pm}0.03mm$(1.3~1.5mm, n=10) and expanded to $1.7{\pm}0.08mm$(1.6~1.8mm, n=10) in diameter in 1.5 hr. The blastodisc was formed in 30 min and cleavage started in 1 hr after fertilization, and the intervals of each stage of cleavage was about 30 min at $25.0^{\circ}C$. The yolk from 32-cell stage to gastrula stage partly depressed and the depressed part moved clockwise. Hatching occurred in 53 hr after fertilization and hatched embryos had 18~19+20~21(38~40) myomeres measuring 4.2~4.3mm in total length. At the age 7 d after hatching, 4 pairs of barbels were already formed ; 1 pair on the posterior part of the nostril, 1 pair on the upper jaw, and 2 pairs on the lower jaw. And the posterior margin of caudal fin changed into two folds. The lateral band and the form of all fins were completed in 3 weeks.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.6
• /
• pp.5-21
• /
• 2014

It has been pointed out that the collapses of unsaturated road embankments caused by earthquake are attributed to high water content caused by the seepage of the underground water and/or the rainfall infiltration. Hence, it is important to study influences of water content on the dynamic stability and deformation mode of unsaturated road embankments for development of a proper design scheme including an effective reinforcement to prevent severe damage. This study demonstrates dynamic centrifugal model tests with different water contents to investigate the effect of water content on deformation and failure behaviors of unsaturated road embankments. Based on the measurement of displacement, the pore water pressure and the acceleration during dynamic loading, dynamic behavior of the unsaturated road embankments with about optimum water content and the higher water content than the optimum one have been examined. In addition, an image analysis has revealed the displacement field and the distributions of strains in the road embankment, by which deformation mode of the road embankment with higher water content has been clarified. It has been confirmed that in the case of higher water content the settlement of the crown is large mainly owing to the volume compression underneath the crown, while the small confining pressure at the toe and near the slope surface induces large shear deformation with volume expansion.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.1
• /
• pp.146-153
• /
• 2001

The difference of composition of composite resin may affect the mechanical properties of composite resin and the environment is important for the properties of materials. The composite resin restoration is always exposed to fluid in oral cavity and the composite resin matrix is able to absorb water, which is accompanied by some swelling of the composite The uptake of water by composites has been correlated with decreases in surface hardness and wear resistance. The purpose of this study was to investigate the effects of water storage in $37^{\circ}C$ distilled water after 7days, 30days, 60days, 120days on compressive strength and flexural strength of dental composite resin, Z-100(group 1) Spectrum(group 2), Clearfil AP-X(group 3), Pyramid(group 4), Heliomolar(group 5). The compressive and flexural strength were measured by instron machine. The following results were obtained: 1. There were significant reduction of compressive strength as water storage time increased, 7days, 30days, 60 days, 120days(p<0.05). 2. There were significant reduction of flexural strength as water storage time increased, 7days, 30days, 60days, 120days(p<0.05). 3. Group 1, 2, 3 -hybrid type showed higher compressive and flexural strength than group 5-microfine type which had lower filler contents.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.38 no.3
• /
• pp.262-269
• /
• 2011

Ameloblastic fibroma is rare true benign mixed odontogenic tumor. Most of these tumors occur in the posterior region of the mandible under 20 years of age. It develops generally associated with unerupted tooth and grows slowly on the surface of alveolar bone, therefore interferes normal tooth eruption. These lesions rarely showing a little bony expansion, are usually asymptomatic and are discovered incidentally on routine dental exam. It is similar to amleoblastic fibroodontoma and ameloblastic fibrodentinoma clinically and roentgenographically but represents no dental hard tissue formation histologically. Enucleation and curettage of surrounding bone are generally recommended options for treatment. Even though there are some reports of recurrence and malignant transformation and more aggressive treatment options like block resection are suggested sometimes, but in most cases, recurrence is unusual because it is well encapsulated and easily separated from adjucent bony socket. In these cases, we did conservative treatment such as enucleation and curettage to the patients who were visited for ameloblastic fibroma associated with delayed eruption of lower first molar. After regular check-ups, we found relatively natural eruption process of combined teeth.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.12
• /
• pp.1427-1430
• /
• 2014

A thermal barrier coating (TBC) prevents heat directly transferring from a high-temperature flame to a substrate. The TBC system comprises a top coating and bond coating. TBC technology reduces the substrate surface temperature by about $100{\sim}170^{\circ}C$. In the TBC system, internal stress is generated by the difference in thermal expansion coefficients of the substrate and coating. The internal stress also differs according to the shape and position of the blade. In this study, finite element analysis was performed for different curvatures of coin-shaped specimens, which are commonly used for thermal fatigue tests, and the changes in internal stress of the TBC system were compared. Based on the results, the curvature at which the minimum stress occurs was derived, and the thermal stress was confirmed to increase with the difference between a given curvature and the curvature with the minimum stress.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.115-115
• /
• 2010

고휘도 고효율 백색 LED (lighting emitting diode)가 차세대 조명광원으로 급부상하고 있다. 백색 LED를 생산하기 위한 공정에서 MOCVD (유기금속화학증착)장비를 이용한 에피웨이퍼공정은 에피층과 기판의 격자상수 차이와 열팽창계수차이로 인하여 생성되는 에피결함의 문제로 기판과 GaN 박막층 사이에 완충작용을 해줄 수 있는 버퍼층 (Buffer layer)을 만든다. 그 위에 InGaN/GaN MQW (Multi Quantum Well)공정을 하여 고휘도 고효율 백색 LED를 구현 할 수 있다. 이 공정에서 기판의 온도가 불균일해지면 wafer 파장 균일도가 나빠지므로 백색 LED의 yield가 떨어진다. 균일한 기판 온도를 갖기 위한 조건으로 기판과 induction heater의 간격, 가스의 흐름, 기판의 회전, 유도가열코일의 디자인 등이 장비의 설계 요소이다. 본 연구에서는 유도가열방식의 유도가열히터를 이용하여 기판과 히터의 간격에 차이에 따른 기판 균일도 측정했고, 회전에 의한 기판의 온도분포와 자기장분포의 실험적 결과를 상용화 유체역학 코드인 CFD-ACE+의 모델링 결과와 비교 했다. 또한 가스의 inlet위치에 따른 기판의 온도 균일도를 측정하였다. 본 연구에서 사용된 가열원은 유도가열히터 (Viewtong, VT-180C2)를 사용했고, 가열된 흑연판 표면의 온도를 2차원적으로 평가하기 위하여 적외선 열화상 카메라 (Fluke, Ti-10)를 이용하여 온도를 측정했다. 와전류에 의한 흑연판의 가열 현상을 누출 전계의 분포로 확인하기 위하여 Tektronix사의 A6302 probe와 TM502A amplifier를 사용했다. 흑연판 위에 1 cm2 간격으로 211곳에서 유도 전류를 측정했다. 유도전류는 벡터양이므로 $E{\theta}$를 측정했으며, 이때의 측정 방향은 흑연판의 원주방향이다. 또한 자기장에 의한 유도전류의 분포를 확인하기 위하여 KANETEC사의 TM-501을 이용하여 흑연판 중심으로부터 10 mm 간격으로 자기장을 측정 했다. 저항 가열 히터를 통하여 대류에 의한 온도 균일도를 평가한 결과 gap이 3 mm일때, 평균 온도 $166.5^{\circ}C$에서 불균일도 6.5%를 얻었으며, 회전에 의한 온도 균일도 측정 결과는 2.5 RPM일 때 평균온도 $163^{\circ}C$에서 5.5%의 불균일도를 확인했다. 또한 CFD-ACE+를 이용한 모델링 결과 자기장의 분포는 중심이 높은 분포를 나타냄을 확인했고, 기판의 온도분포는 중심으로부터 55 mm되는 곳에서 300 W/m3로 가장 높은 분포를 나타냈다. 가스 inlet 위치를 흑연판 중심으로 수직, 수평 방향으로 흘려주었을 때의 불균일도는 각각 10.5%, 8.0%로 수평 방향으로 가스를 흘려주었을 때 2.5% 온도 균일도 향상을 확인했다.