• The korean journal of orthodontics
• /
• v.31 no.6 s.89
• /
• pp.601-610
• /
• 2001

The purpose of this retrospective study was to evaluate the level oi alveolar bone support of the erupted Permanent canine through the reconstructed cleft region compared to the contralateral canine on the non-cleft side. This study was limited to children with complete unilateral cleft lip and palate who underwent secondary alveolar iliac bone gvaft and the apices of the erupted canine roots were closed at the time of evaluation. With these criteria the study included 21 children whose average age at the time of bone graft reconstruction was 9.8 years, with a minimum of 12.4 years of age at the time of the evaluation. The study was limited to the use of iliac cancellous bone as the autograft material for reconstruction of the alveolar cleft. Cranial bone graft and other autogenous bone sources were excluded. The periapical radiographs were used to evaluate alveolar bone level of each canine. The percentages of root supported by the bone were established by dividing the amount of root covered with the bone by the anatomic root length. The canine oi the non-cleft side was used as an internal control and the canine on the cleft side was used as an experimental. There was a statistically significant difference in the alveolar bone support ratio between the control ($92.9\%$) and experimental canines ($8.7\%$). An average of $95\%$ level of alveolar bone support was achieved for the experimental canine in comparison to the control canine. Neither the presence of lateral incisor, nor the stage of root development of the canine at the time of the bone graft appeared to have affected the alveolar bone support ratio of the canine after the secondary bone graft.

• Journal of the Korean Professional Engineers Association
• /
• v.28 no.4
• /
• pp.54-75
• /
• 1995

This synthesis has been prepared from a review of literature on Truck Escape Ramps technology and a survey of current practice by state department of transportation. Their locations have been determined usually from a combination of accident experience and en-gineering judgement, but new tools are emerging that can identify needs and sites without waiting for catastrophic accidents to happen. The Grade Severity Rating Systems holds promise in this regard. Design Procedures for truck excape ramps continue to evolve. Gravel arrester beds are clearly the preferred choice across the country Rounded aggregate, uniformly graded in the approximate size range of 13 to 18mm. Tech-nical publications typically have dassified TER types as paved gravity, sandpile, and ar-rester bed ramps. The design speed for vehicle entry into the ramp in critical to the deter-mination of ramp length. An escape ramp should be designed for a minimum entry speed of 130km/hr, a 145km/hr design being preferred. The ramps should be straight and their angle to the roadway align-ment should be as possible. The grade of truck escape ramps show the adjustment of ramp design to local topography, such as the tradeoff of ramp length against earthwork requirements. A width of 9 to 12m would more safety acommodate two or more outof con-trol vehicles. Reguarding comments on the most effective material, most respondents cited their own specification or referred to single graded, rounded pea gravel. The consensus essentially Is that single graded, well -rounded gravel is the most desirable material for use in arrester beds. The arrester beds should be constructed with a minimum aggregate depth of 30cm. Successful ramps have used depths between 30 and 90cm.

• Elastomers and Composites
• /
• v.10 no.2
• /
• pp.136-156
• /
• 1975

고무는 불량열전도체(不良熱傳導體)이며 두께가 두꺼우면 내부(內部)가 적정온도수준(適正溫度水準)에 이르기 전까지 가황시간(加黃時間)이 길어진다. 가황온도(加黃溫度)가 상승(上昇)할수록 가황물(加黃物)의 물성(物性)은 열화(劣化)되는 경향(傾向이) 있다. 천연(天然)고무든지 합성(合成)고무든지 간(間)에 과가황(過加黃)에 대(對)한 저항성(抵抗性)이 나쁘므로 특(特)히 고온가황(高溫加黃)에 대(對)해 민감(敏感)하다. 이것은 고온(高溫)에서 단시간(短時間) 가황(加黃)일수록 가속(加速)된다. 평탄가황배합물(平坦加黃配合物)의 경우에서 보더라도 내부(內部)가 적절(適切)히 가황(加黃)되기도 전(前)에 외부(外部)는 과가황(過加黃)이 되는 수가 있다. 근래(近來) 발간(發刊)된 문헌(文獻)에서도 이러한 내용(內容)이 잘 설명(說明)이 되어 있는데 다른 각도(角度)에서 고찰(考察)해 볼것 같으면 정체시간(停滯時間)이 비교적(比較的) 길지 않는 한(限) 가황시간(加黃時間)은 정체시간(停滯時間)과 sheet 가황시간(加黃時間)과의 합(合)이라고 말할 수 있겠다. 예(例)를 들어 설명(說明)하자면 $130^{\circ}C(266^{\circ}F)$에서 정체시간(停滯時間)이 10분(分)이고 sheet 가황시간(加黃時間)이 20분(分)인 제품(製品)은 이 온도(溫度)에서 30분간(分間) 가황(加黃)해야 된다는 것이다. 온도계수(溫度係數)를 2라고 가정(假定)할 경우 $140^{\circ}C(284^{\circ}F)$에서의 가황시간(加黃時間)은 $30\times\frac{1}{2}=15$분(分)이 아니라 $20\times\frac{1}{2}+10=20$분(分)이 된다. 크기가 큰 제품(製品)은 보통(普通) 다음에 있는 여러 방법(方法)들 가운데 한 가지 또는 여러가지를 조합(組合)하여 가황(加黃)시킨다. a) 크기가 작은 것에 대한 것 보다 낮은 온도(溫度)에서 가황(加黃)한다. b) 침투가황-제품(浸透加黃-製品)을 가압하(加壓下)에 두고서 외부가황(外部加黃)은 단속(斷續)시키고 열(熱)이 중심(中心)으로 침투(浸透)하게 한다. c) 단계가황(段階加黃)-처음에는 저온(低溫)에서 시작(始作)하여 일정간격(一定間隔)을 두고 점차(漸次) 온도(溫度)를 상승(上昇)시켜 최종적(最終的)으로 가황온도(加黃溫度)까지 올린다. d) 가능(可能)하다면 metal base나 금형(金型)에서 고무를 증기가황(蒸氣加黃)시킬 경우에 있어서 속이 빈 축(軸)을 사용하여 내부(內部)로 부터 가열(加熱)하면 가황시간(加黃時間)이 단축(短縮)된다. e) 냉각중(冷却中)의 후가황(後加黃)-이것은 가열장치(加熱裝置)에서 끄집어낸 후 제품(製品)의 외부(外部)를 냉각(冷却)시키는 방법(方法)이다. 가열(加熱)된 제품(製品)이 쌓여 있거나 적절(適切)하게 냉각(冷却)되지 않을 때 가황(加黃)이 추가적(追加的)으로 되거나 과가황(過加黃)이 될 우려가 있는 제조공정(製造工程)에서는 흔히들 이 방법(方法)을 무시(無視)하고 있다. 여기서 강조(强調)해 두어야 할 것은 항상 제품(製品)의 외부(外部)를 완전(完全)히 가황(加黃)시킬 필요(必要)는 없다는 것이다. 다공성(多孔性)이나 기포생성(氣泡生成)을 조장(助長)하는 불량가황상태(不良加黃狀態)와 표면(表面)에서의 과가황상태간(過加黃狀態間)의 균형(均衡)을 취(取)해 줘야 하는데 물론(勿論) 이때는 가황시간(加黃時間)을 단축(短縮)시켜야 한다는 경제적(經濟的)인 측면(側面)도 아울러 고려(考慮)해야 한다. 이것은 고무기술자(技術者)가 당면(當面)해야할 과제(課題)에 속(屬)하며 바람직 한것은 본장(本章)의 내용(內容)이 여러 상황하(狀況下)에서 당면(當面)한 문제(問題)에 대(對)해 어떻게 대처(對處)해 야 할지를 모르는 여러 기술자(技術者)들에게 도움이 되었으면 하는 것이다.

• Journal of the Korean Electrochemical Society
• /
• v.20 no.1
• /
• pp.7-12
• /
• 2017

Using a precursor of $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ as a starting material, a surface-modified cathode material was obtained by coating with KCl, where the added KCl reduces residual Li compounds such as $Li_2CO_3$ and LiOH, on the surface. The resulting electrochemical properties were investigated. The amounts of $Li_2CO_3$ and LiOH decreased from 8,464 ppm to 1,639 ppm and from 8,088 ppm to 6,287 ppm, respectively, with 1 wt% KCl added $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ that had been calcined at $800^{\circ}C$. X-ray diffraction results revealed that 1 wt% of KCl added $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ did not affect the parent structure but enhanced the development of hexagonal crystallites. Additionally, the charge transfer resistance ($R_{ct}$) decreased dramatically from $225{\Omega}$ to $99{\Omega}$, and the discharge capacity increased to 182.73mAh/g. Using atomic force microscopy, we observed that the surface area decreased by half because of the exothermic heat released by the Li residues. The reduced surface area protects the cathode material from reacting with the electrolyte and hinders the development of a solid electrolyte interphase (SEI) film on the surface of the oxide particles. Finally, we found that the introduction of KCl into $LiNi_{0.6}Co_{0.2}Mn_{0.2}O_2$ is a very effective method of enhancing the electrochemical properties of this active material by reducing the residual Li. To the best of our knowledge, this report is the first to demonstrate this phenomenon.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.7
• /
• pp.7-14
• /
• 2009

In this paper, the effects of annealing conditions on the structural ((002) intensity, FWHM, d-spacing, grain size, (002) peak position), optical (UV peak, UV peak position) and electrical properties (carrier concentrations, resistivity, mobility) of ZnO films were investigated. ZnO films were deposited onto SiO$_2$/si substrates by RF magnetron sputtering from a ZnO target. The substrate was not heated during deposition. ZnO films were annealed in temperature ranges of $500\sim650^{\circ}C$ in the O$_2$ flow for 5$\sim$20 min. The film average thicknesses were in the range of 291 nm. The surface morphologies and structures of the samples were characterize by SEM and XRD, respectively. The optical properties were evaluated by photoluminescence (PL) measurement at room temperature (RT) using a He-Cd 325 nm laser. As the annealing temperature and time vary, the following relations were also observed: (1) proportional relationships among UV intensity (002) intensity, and grain size exist, (2) UV intensity is inversely proportional to FWHM, (3) there is no special relationship between UV intensity and electron carrier concentrations, (4) d-spacing is inversely proportional to (002) peak position, (5) UV peak position in the range of 3.20$\sim$3.24 eV means that ZnO films have a n-type conductivity which was consistent with that obtained from the electrical property, (6) the optimal conditions for the best optical and structural characteristics were found to be oxygen fraction, (O$_2$/(O$_2$+Ar)) of 0.2, RF power of 240W, substrate temperature of RT, annealing condition of 600$^{\circ}C$ for 20 min, and sputtering pressure of 20 mTorr.

• International Journal of Highway Engineering
• /
• v.11 no.3
• /
• pp.97-109
• /
• 2009

One of the main causes of asphalt rutting is high temperature of the pavement. Nevertheless, there has been few research on lowering the pavement temperature for reducing rutting. This study investigated the performance characteristics of moisture-retaining porous asphalt pavement, which is known to have a temperature reducing effect. The purpose of this study is to quantify the temperature reducing effect of moisture-retaining porous asphalt pavement and its effect of reducing rutting through Accelerated Pavement Testing(APT). Additionally, the possibility of reducing the thickness of the pavement in comparison to general dense grade pavement by analyzing structural layer coefficient of moisture retaining pavement. A total of three test sections consisting of two moisture-retaining porous asphalt pavement sections and one general dense-grade porous asphalt pavement section were constructed for this study. Heating and spraying of water were carried out in a regular cycle. The loading condition was 8.2 ton of wheel load, the tire pressure of $7.03kgf/cm^2$, and the contact area of $610cm^2$. The result of this experiment revealed that the temperature reducing effect of the pavement was about $6.6{\sim}7.9^{\circ}C$(average of $7.4^{\circ}C$) for the middle layer and $7.9{\sim}9.8^{\circ}C$(average of $8.8^{\circ}C$) for surface course, resulting in a rutting reduction of 26% at the pavement surface. Additionally, the structural layer coefficient of moisture retaining pavement measured from a laboratory test was 0.173, about 1.2 times that of general dense grade pavement. The general dense-grade porous asphalt pavement test section exhibited rutting at all layers of surface course, middle layer, and base layer, while the test sections of moisture-retaining porous asphalt pavement manifested rutting mostly at surface course only.

• Korean Journal of Food Science and Technology
• /
• v.34 no.2
• /
• pp.255-262
• /
• 2002

This experiment was performed to improve the stability of Lactobacillus fermentum YL-3 as a poultry probiotics. The culture conditions that improve acid tolerance of L. fermentum YL-3 were investigated by changing several factors such as medium composition, temperature, anaerobic incubation and culture time. Also, L. fermentum YL-3 was encapsulated with alginate, calcium chloride and chitosan. The stable culture conditions of L. fermentum YL-3 were obtained in anaerobic incubation using MRS media without tween 80 for 20 hour at $42^{\circ}C$. The capsule after treatment with 1% chitosan was formed close membrane by a bridge bond. Immobilization of L. fermentum YL-3 in capsule was observed by confocal laser scanning microscopy, and cell viability was $2.0{\times}10^9\;CFU/g$ above the average. L. fermentum YL-3 capsule after acid treated at pH 2.0 for 3 hour survived about 40%, but those encapsulated with 1% chitosan survived about 65%. Survival rate of capsule stored at room temperature decreased about $2{\sim}3$ log cycle during 3 weeks, but viability of capsule stored at $4^{\circ}C$ during 3 weeks maintained almost $10^8\;CFU/g$ levels.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.1-6
• /
• 2011

A transparent oxide thin film transistors (Transparent Oxide-TFT) have been fabricated by RF magnetron sputtering at room temperature using amorphous indium zinc oxide (a-IZO) as both of active channel and source/drain, gate electrodes and co-sputtered $HfO_2-Al_2O_3$ (HfAIO) as gate dielectric. In spite of its high dielectric constant > 20), $HfO_2$ has some drawbacks including high leakage current and rough surface morphologies originated from small energy band gap (5.31eV) and microcrystalline structure. In this work, the incorporation of $Al_2O_3$ into $HfO_2$ was obtained by co-sputtering of $HfO_2$ and $Al_2O_3$ without any intentional substrate heating and its structural and electrical properties were investigated by x-ray diffraction (XRD), atomic force microscopy (AFM) and spectroscopic ellipsometer (SE) analyses. The XRD studies confirmed that the microcrystalline structures of $HfO_2$ were transformed to amorphous structures of HfAIO. By AFM analysis, HfAIO films (0.490nm) were considerably smoother than $HfO_2$ films (2.979nm) due to their amorphous structure. The energy band gap ($E_g$) deduced by spectroscopic ellipsometer was increased from 5.17eV ($HfO_2$) to 5.42eV (HfAIO). The electrical performances of TFTs which are made of well-controlled active/electrode IZO materials and co-sputtered HfAIO dielectric material, exhibited a field effect mobility of more than $10cm^2/V{\cdot}s$, a threshold voltage of ~2 V, an $I_{on/off}$ ratio of > $10^5$, and a max on-current of > 2 mA.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.2
• /
• pp.222-231
• /
• 2009

Statements of the problem: Over the past decades, conventional complete dentures were used for various patients although they have incomplete function. Overdentures using dental implants could help the improvement of denture function. Purpose: The purpose of this study was to compare the strains of abutment and bone on implant overdenture between splinted and unsplinted type of prosthesis. Additionally, the strain values of parallel placed implant model and unparallel placed implant model were compared. Material and methods: Two acrylic resin model were prepared and two implants were placed at the canine positions in each model. In the first model, two implant were placed parallel. In the second model, two implants were placed with 10 degree labiolingual divergence. Two types of abutment were connected to the fixtures alternatively. One was splint type of Hader bar, the other was unsplint type of ball abutment. Overdentures were fabricated with corresponding attachment systems and seated on abutments. Strains of abutments and labial bone simulants were measured with electric resistance strain gauges when static load from 100 N to 200 N were applied to overdentures. Results: 1. Splinted type of overdentures using bar and clip showed higher absolute strain values. But the strain was compressive and the load was shared by two implants(P<.05). 2. Unsplinted type overdentures using ball and O-ring showed low absolute strain values(P<.05). 3. Labially inclined implant showed higher tensile strain values in unsplinted type of prosthesis than in splinted type of prosthesis. Lingually inclined implant showed rather low strain values under load(P<.05). 4. Non parallel implant model showed higher absolute strain values than parallel placed implant model comprehensively(P<.05).

• Food Science and Preservation
• /
• v.15 no.1
• /
• pp.49-57
• /
• 2008

This study was conducted to develop an optimal composite recipe for a cookie including yam powder that would be attractive to all age groups. Wheat flour was partially substituted by yam powder to reduce the content of wheat flour. This study has produced the sensory optimal composite recipe by making cookies, respectively with each 5 level of yam powder $(X_1)$, Sugar$(X_2)$, butter$(X_3)$, by C.C.D (Central Composite Design) and conducting sensory evaluation and instrumental analysis by means of RSM (Response Surface Methodology). Sensory items showed very significant values in color, softness, overall quality (p<0.01), flavor (p<0.05) and those of instrumental analysis showed significant values in lightness, redness (p<0.05), spread ratio, hardness (p<0.01). Also sensory optimal ratio of yam cookie was calculated at yam powder 37.35 g, sugar 50.75 g, butter 78.40 g and it was revealed that the factors of influencing yam cookie aptitude were in older of yam powder, butter, sugar.