• Applied Chemistry for Engineering
• /
• v.16 no.6
• /
• pp.827-833
• /
• 2005

This study focused on the establishment of optimum formulation of polyamide based hot melt adhesive through adhesive synthesis, study of physical property, and adhesion study. In the previous study, the optimum formulation of base resins (CM831, 843P) and tackifying resin (terpene resin) was determined. The weight ratio of CM831, 843P, and terpene resin was 75, 25, and 10, respectively. Based on the optimum formulation, the effect of wax and filler addition was examined in this study. According to the results, the maximum adhesion strength with the steel could be obtained by the addition of 5 wt% of polyethylene wax although the melt viscosity of adhesive decreased continuously with the addition of wax. In the case of filler, the optimum adhesion property could be achieved by the addition of 10 wt% of talc. However, the addition of filler caused little increase of melt viscosity of adhesive.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.311-321
• /
• 2021

Many studies have been performed on hybrid fiber reinforced concrete for years, which is to improve some of the weak material properties of concrete. Studies on characteristics of hybrid fiber reinforced concrete using amorphous steel fiber and organic fiber, however, yet remain to be done. The purpose of this research is to evaluate the compressive and tensile behaviors and then propose a material model of high performance hybrid fiber reinforced concrete using amorphous steel fiber and polyamide fiber. For this purpose, the high performance hybrid fiber reinforced concretes were made according to their total volume fraction of 1.0% for target compressive strength of 40MPa and 60MPa, respectively, and then the compressive and tensile behaviors of those were evaluated. Also, based on the experimental results of the high performance hybrid fiber reinforced concrete and mortar, each material model for the compressive and tensile behavior was suggested. It was found that the experimental results and the proposed models corresponded relatively well.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.458-466
• /
• 2020

The purpose of this experimental research is to evaluate the compressive and tensile behaviors of high performance hybrid fiber reinforced concrete(HPHFRC) using amorphous steel fiber(ASF) and polyamide fiber(PAF). For this purpose, the HPHFRCs using ASF and PAF were made according to their total volume fraction of 1.0% for target compressive strength of 40MPa and 60MPa, respectively. And then the compressive and tensile behaviors such as the compressive strength, compressive toughness, direct tensile strength, and stress-strain characteristics under compressive and tensile tests were estimated. It was observed from the test results that the compressive strength of HPHFRC was slightly decreased than that of plain concrete, but the compressive toughness, compressive toughness ratio, and direct tensile strength of HPHFRC increased significantly. Also, it was revealed that the plain concrete showed brittle fracture after the maximum stress from the stress-strain curves, but HPHFRC showed strain softening.

• Fashion & Textile Research Journal
• /
• v.24 no.1
• /
• pp.146-155
• /
• 2022

We proposed a simple process of creating electroconductive textiles by using PEDOT:PSS(Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate))/non-oxidized graphene to coat polyamide or polyurethane knitted fabric for smart healthcare purposes. Electroconductive textiles were obtained through a coating process that used different amounts of PEDOT:PSS/non-oxidized graphene solutions on polyamide/polyurethane knitted fabric. Subsequently, the surface, electrical, chemical, weight change, and elongation properties were evaluated according to the ratio of PEDOT:PSS/non-oxidized graphene composite(1.3 wt%:1.0 wt%; 1.3 wt%:0.6 wt%; 1.3 wt%:0.3 wt%) and the number of applications(once, twice, or thrice). The specimens' surface morphology was observed by FE-SEM. Further, their chemical structures were characterized using FTIR and Raman spectroscopy. The electrical properties measurement (sheet resistance) of the specimens, which was conducted by four-point contacts, shows the increase in conductivity with non-oxidized graphene and the number of applications in the composite system. Moreover, a test of the fabrics' mechanical properties shows that PEDOT:PSS/non-oxidized graphene-treated fabrics exhibited less elongation and better ability to recover their original length than untreated samples. Furthermore, the PEDOT:PSS/non-oxidized graphene polyamide/polyurethane knitted fabric was tested by performing tensile operations 1,000 times with a tensile strength of 20%; Consequently, sensors maintained a constant resistance without noticeable damage. This indicates that PEDOT:PSS/non-oxidized graphene strain sensors have sufficient durability and conductivity to be used as smart wearable devices.

• Textile Coloration and Finishing
• /
• v.13 no.3
• /
• pp.165-171
• /
• 2001

In this study, UV/vis. spectra of color solution extracted from onion shell and dyeing properties of polyamide fibers such as wool, silk, and nylon were investigated. Also, the effect of mordanting on wash fastness and light fastness was Investigated. The amount of colors extracted was increased with extracting temperature and time. The wavelength of maximum absorption of onion shell extract corresponds to flavonol peak and quercetin peak. Also, spectra of color solution were shifted to longer wavelength at higher pH values. It appeared that the optimum condition of the dyeing of wool, nylon, and silk fabrics with onion shell extract was $60^\circ{C}$ , 30min, and pH 4.0 of dyed bath. Surface colors of the dyed fabrics were different according to the used mordants: Al and Cr mordanted fabrics were dyed in yellowish colors, Cu mordanted fabric in greenish color, Sn mordanted fabric in orange color, and Fe mordanted fabric in khaki color. The mordanting was effective at improving wash fastness and light fastness.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.308-311
• /
• 2004

Nowadays, plastic industry has needed to produce parts that require high precision and quality. To make a high precision and quality part, before injection molding, plastic material is investigated about their properties such as shrinkage, warpage, etc. In this study, experiments were conducted with PA6(polyamid) to figure out shrinkage behavior according to three type aspect ratio of samples. The injection speed that affects on shear rate, molecular orientation within plastic part was determined as main variable of experiment. As a result of experimental study, part shrinkage had a tendency to be decreased by increasing injection speed and aspect ratio of samples.

• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.51-55
• /
• 2003

Recently the requirements for light weight and high performance of the automobile have increased. Especially, the plastic fuel tube makers have made their efforts to dove]op the various plastic fuel tube module with not only dimensional accuracy but also cost competitiveness. The experiment is performed to investigate spring backs for PA12 plastic fuel tubes in case of compound bending. In the experiment, steam bending process is adopted as bending method. In this study, the results we obtained are used to design the bending fixtures and the compound bending system.

• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.56-60
• /
• 2003

Recently the plastic fuel tube is usually used to reduce production cost and weight in automobiles. These days, material used to plastic fuel tube is the polyamide12. The fuel tube is made of the PA12. Post deformation of the tube has been changed by environmental temperature. So, it is important to prevent post deformation. The experiment is performed to investigate post deformation of the tube produced by each bending process. In this study, the results we obtained are used to bending process system for post deformation as the environmental temperature of the tube. It turned out that the method of steam heating and air cooling was shown less deformation than other methods.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1404-1409
• /
• 2007

Polymers for laser sintering were needed in order to fabricate the articles with the three-dimensional duplication equipment of SLS (selective laser sintering) process. The thermal properties, particle size, distribution, and shape of polymer powder had a close relation with the processibility of laser sintering. In this study, we prepared new polymer powders with uniform size and higher bulk density by wet process. Wet process consists of several finely-controlled steps such as dissolution, nucleation, propagation and crystallization. Several additives were added to improve the thermal, rheological, and flow properties.

• Textile Coloration and Finishing
• /
• v.5 no.2
• /
• pp.134-138
• /
• 1993

Wool, silk and nylon 6 fabrics were treated with low-temperature plasma under atmospheric pressure of acetone/argon or helium/argon for 30 and 180 sec, and then dyed with leveling type acid dye, C.I. Acid Red 18 and milling type acid dye, C.I. Acid Blue 83. In spite of short time of the plasma treatment for thirty seconds, the color depth of wool fabrics was increased remarkably with both of the plasma gases, aceton/argon or helium/argon and with the kinds of dyes i.e., levelin type or milling type. But the atmosperic low-temperature plasmas did not increase the depth of silk and nylon 6 fabrics dyed with both of the acid dyes regardless of the teated time and plasma gases. It seems that low-temperature plasma by atmospheric-pressure discharge is effective for improvement of dyeing of wools as is the same way with the low-temperature plasma by glow discharge. The kinds of plasma gases and treated time did not influnce the depth of wool fabric pretreted with the atmosperic low-temperature plasmas.