• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.3
• /
• pp.187-193
• /
• 2004

In this study, Anaerobic sewage sludge in a batch reactor operation at $35^\circ{C}$ was used as the seed to investigate the effect of pretreatments of waste activated sludge and to evaluate its hydrogen production potential by anaerobic fermentation. Various pretreatments including physical, chemical and biological means were conducted to utilize for substrate. As a result, SCODcr of alkali and mechanical treatment was 15 and 12 times enhanced, compared with a supernatant of activated sludge. And SCODcr was 2 time increase after re-treatment with biological hydrolysis. Those were shown that sequential hybridized treatment of sludge by chemical & biological methods to conform hydrogen production potential in bath experiments. When buffer solution was added to the activated sludge, hydrogen production potential increased as compare with no addition. Combination of alkali and mechanical treatment was higher in hydrogen production potential than other treatments.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.7
• /
• pp.387-395
• /
• 2015

Anaerobic mesophilic batch test of several organic wastes were carried out by a graphical statistic analysis (GSA) to evaluate their ultimate biodegradability and two distinctive decay rates ($k_1$ and $k_2$) with their corresponding degradable substrate fractions ($S_1$ and $S_2$). Each 3 L batch reactor was operated for more than 100 days at the substrate to inoculum ratio (S/I) of 0.5 as an initial total volatile solids (TVS) mass basis. Their Ultimate biodegradabilities were obtained respectively as follow; 69% swine waste, 45% dairy cow manure, 66% slaughterhouse waste, 79% food waste, 87% food waste leachate, 68% primary sludge and 39% waste activated sludge. The readily biodegradable fraction of 89% ($S_1$) of Swine Waste BVS ($S_o$) degraded with in the initial 31 days with $k_1$ of $0.116day^{-1}$, where as the rest 11% slowly biodegradable fraction ($S_2$) of BVS degraded for more than 100 days with the long term batch reaction rates ($k_2$) of $0.004day^{-1}$. For the Food Waste and Waste Activated Sludge, their readily biodegradable portions ($S_1$) appeared 89% and 80%, which degrades with $k_1$ of $0.195day^{-1}$ and $0.054day^{-1}$ for an initial 15 days and 28 days, respectively. Their corresponding long term batch reaction rates ($k_2$) were $0.003day^{-1}$ and $0.002day^{-1}$. Results from other organic wastes are addressed in this paper. The theoretical hydraulic retention times (HRTs) of anaerobic digesters treating organic wastes are easily determined by the analysis of multiple decay rate coefficients ($k_1$ and $k_2$) and their corresponding biodegradable substrate fractions ($S_1$ and $S_2$).

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.3
• /
• pp.463-473
• /
• 2000

This research was carried out to investigate chemical pretreatment using limestone in treating abandoned metallic mine drainage with anaerobic biological treatment, and to estimate application of papermill and livestock sludge as carbon sources for SRB (Sulfate Reducing Bacterial. Capacity of anaerobic limestone bed was steeply decreased. But if limestone was utilized as pretreatment process in treating them with anaerobic biological treatment. it could look forward to stabilize system because it did initally neutralize them. Effluent SCOD in R-4 was lower than R-l~R-3 in inital HRT 5day but its concentration was high in HRT 1day after passed time. Therefore in point of durability and supply of organic matter. it seemed that R-4 was useful became organic matter in R-4 was not consumed by excessive degradation within short period. In all reactors, pH was suitable for SRB growth in whole HRT, but on the evidence of ORP, SRB was active after HRT 2day. Fixation trend of heavy meta s showed high as $SO_4{^{2-}}$ reduction efficiency increased, and $SO_4{^{2-}}$ reduction and fixation of heavy metals were relatively high in HET 2day.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.5
• /
• pp.555-561
• /
• 2005

A new graphical method was developed to separate two distinctive decay rate coefficients($k_1$ and $k_2$) at their respective degradable substrate fractions($S_1 and $S_2$). The mesophilic batch reactor showed $k_1$ of $0.151\;day^{-1}$ for wasted activated sludge(WAS), $0.123\;day^{-1}$ for thickened sludge(T-S), $0.248{\sim}0.358\;day^{-1}$ at S/I ratio of $1{\sim}3$ for sorghum and $0.155{\sim}0.209\;day^{-1}$ at S/I ratio $0.2{\sim}1.0$ for swine waste, whereas their long term batch decay rate coefficients($k_2$) were $0.021\;day^{-1}$, $0.001\;day^{-1}$, $0.03\;day^{-1}$ and $0.04\;day^{-1}$ respectively. At least an order of magnitude difference between $k_1$ and $k_2$ was routinely observed in the batch tests. The portion of $S_1$, which degrades with each $k_1$ appeared 71% for WAS, 39% for T-S, 90% for sorghum, and $84{\sim}91%$ at S/I ratio of $0.2{\sim}1.0$ for swine waste. Ultimate biodegradabilities of 50% for WAS, 40% of T-S, $82{\sim}92%$ for sorghum, and $81{\sim}89%$ for swine waste were observed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.16-23
• /
• 2018

Alternative technologies for sludge treatment and disposal need to be developed urgently because the amount of produced production has increased continuously. In this study, Pulsed Electric Fields (PEF) technique was applied for sludge solubilization and the performance was evaluated. The PEF equipped with electrodes coated by epoxy resin and teflon was inducted to the activated sludge suspension, and the effect of the coating materials on the solubilization was determined. In addition, the effect of the applied voltage on the solubilization yield was investigated as the applied voltage was increased from 6 to 12 and 15 kV. Sludge solubilization was not observed when the epoxy-coated electrode was used for PEF induction regardless of the applied voltage. However, sludge solubilization occurred when 12 and 15 kV were applied to the teflon-coated electrodes. The MLSS decreased to 9%, and the soluble-COD increased to 496% when the applied voltage was 15 kV. But sludge solubilization did not happen under 6 kV condition. The corona discharge was observed at applied voltages of 12 and 15 kV, (Ed- sorry but I cannot understand the following highlight) but if 6 kV, strongly indicating that the corona discharge make the sludge solubilized, which suggests that the critical voltage for sludge solubilization lies between 6 and 12 kV. Consequently, proper selection of electrode-coating materials and the applied voltage of PEF could lead to sludge solubilization by corona discharge.

• Journal of Korean Society of Water and Wastewater
• /
• v.33 no.4
• /
• pp.291-297
• /
• 2019

Phosphorus is a vital resource for sustaining agriculture and nutrition, but a limited non-renewable resource. Thus, the recovery of phosphorus from waste activated sludge(WAS) was attempted by microwave heating and magnesium ammonium phosphorus(MAP) crystallization. Polyphosphate-accumulating organisms(PAOs) in WAS release phosphate from the cell when they are exposed to high temperature environments. Microwave heating caused phosphorus and ammonia to release from WAS. The amount was increased with increasing temperature, showing that 88.5% of polyphosphate present in the cells were released in the form of phosphate at $80^{\circ}C$. A similar result was also observed in the release of ammonia. On the other hand, both phosphorus and ammonia were crystallized with magnesium, and then was harvested as MAP. Phosphorus recovery rate reached almost 97.8%, but the ammonia was about 13.4%. These results cleary indicate that phosphorus could be recovered from WAS using a physiological trait of PAOs. Heavy metal analyses also show that the MAP crystal is useful and safe as a phosphorus fertilizer.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.299-306
• /
• 2005

Anaerobic fermentation of food waste (FW) and waste activated sludge (WAS) for hydrogen production was performed in CSTR (Continuous Stirred tank reactor) under various HRTs and volumetric mixing ratio (V/V) of two substrates, FW and WAS. The specific hydrogen production potential of FW was higher than that of WAS. However, pH drop in the CSTR for hydrogen production from FW was higher than that from WAS. The maintenance of desired pH during fermentative hydrogen production is regarded as the most important operation parameter for the stable hydrogen production. Therefore, when the potential of hydrogen production from FW and better buffer capacity of WAS, the proper mixture of FW and WAS for fermentative hydrogen production were considered as a useful complementary substrate. The maximum yield of specific hydrogen production, 140 mL/g VSS, was found at HRT of 2 day and the volumetric mixing ratio of 20:80 (WAS : FW). The spatial distribution of hydrogen producing bacteria was observed in anaerobic fermentative reactor using fluorescent in situ hybridization (FISH) method.

• Journal of Environmental Science International
• /
• v.14 no.9
• /
• pp.881-888
• /
• 2005

The biosorption of dye, Rhodamine B(Rh-B), onto waste activated sludge was investigated. The biosorption capacity and contact time were shown as a simulation of dye adsorption equilibrium and kinetics models. We observed that biosorption of Rh-B occurred rapidly less than 4 hr. These experimental data could be better fitted by a pseudo-second-order rate equation than a pseudo-first-order rate equation. The equilibrium dependence between biosorption capacity and initial concentration of Rh-B was estimated and it was found that the equilibrium data of biosorption were fitted by four kinds of model such as Langmuir, Freundlich, Redlich-Peterson, and Koble-Corrigan model. The average percentage errors, $\varepsilon(\%)$, observed between experimental and predicted values by above each model were $21.19\%,\;9.97\%,\;10.10\%\;and\;11.76\%$, respectively, indicating that Freundlich and Redlich-Peterson model could be fitted more accrately than other models.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.179.2-179.2
• /
• 2011

바이오매스 가스화 프로세스 개발에 있어서 가장 기본적인 해결과제는 고발열량의 합성가스 제조, 냉가스 효율의 향상, 타르 발생량 저감 및 제거이다. 가스화 효율 향상에 대한 연구는 국내외 적으로 많이 이루어지고 있으나, 타르 발생량 저감에 대한 연구는 많이 이루어져 있지 않다. 타르는 분자량이 큰 방향적 탄화수소로 응축되면 점성이 높아 배관폐쇄, 정제설비의 압력손실 증가로 인해 운전정지 및 가스화율 저하의 원인이 된다. 가스화로에서 타르 발생량을 저감시키는 방법 중에는 Ni계 촉매를 이용하는 방법이 있으나, 카본 누적에 의한 활성저하, 알칼리금속에 의한 응집 등의 문제가 발생할 수 있다. 한편 철산화물은 합성가스 중의 C2-C3계의 타르를 분해하는데 효과가 알려져 있다. 따라서 본 연구에서는 적벽돌, 염색슬러지 회재 등에는 철산화물이 다량 함유되어 있는 것에 착안하여 폐기물중의 폐금속을 이용한 바이오매스 가스화에 대한 연구를 수행하였다. 점토광물계 폐기물인 적벽돌 파쇄물($SiO_2$ 67.2%, $Al_2O_3$ 19.7%, $Fe_2O_3$ 8.7%, $K_2O$ 2.0%, $TiO_2$ 1.2%, MgO 0.7%)을 전처리 한 후 유동매체로하여 우드펠렛을 가스화한 결과, 가스 생성량이 증가하고, 타르 및 탄화수소류가 감소하는 경향을 나타내었다. 특히 타르는 후단의 타르 트랩에서 타르가 거의 검출이 되지 않았다. 전처리를 하지 않은 적벽돌 파쇄물은 반응시간이 경과한 후에 가스화율이 증가함에 따라 철화합이 가스화로내에서 환원되어 타르를 분해하는데에는 어느 정도의 반응시간이 필요한 것을 확인하였다.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.5
• /
• pp.571-580
• /
• 2008

The influence of bacterial stress on anaerobic hydrogen-producing microorganisms was investigated in batch tests using serum bottles. Several physical and chemical stresses (i.e., heating, adding methane producing inhibitor and chemical acidification) were adapted as a pretreament of the seed sludge. In this experiment, the cultivation temperature were set at mesophilic ($35^{\circ}C$) and thermophilic conditions ($55^{\circ}C$) with adjusting pH at 5, 6, and 7 when using the mixture of food waste and activated sludge as a substrate. In conjunction with the pretreatment, hydrogen production was significantly enhanced as compared with that from untreated sludge. However, less biogas (hydrogen and methane) was produced without the pH control, resulted from the decrease of pH to below 4, mainly due to the formation of VFAs. Hydrogen and carbon dioxide gas were analyzed as main components of the biogas while methane not detected. With an application of chemical acidification, the highest hydrogen production value of 248 ml/l/day achieved at pH 7 and $35^{\circ}C$. In addition, more hydrogen gas produced when the ratio of butyric/acetic acid ratio increased. The optimum pH and temperature for hydrogen production were found to be 7 and $35^{\circ}C$, respectively.