• Journal of Korea Society of Waste Management
• /
• v.35 no.8
• /
• pp.770-776
• /
• 2018

This study measured the energy recovery rate of each municipal waste incineration facility according to the revised energy recovery rate estimation method, which targeted four municipal waste incineration facilities (Unit No. 7). The results calculated by the measuring instruments were used for each factor to estimate the recovery rate, and the available potential of available energy was examined by analyzing the energy production and valid consumption. As a result of the low heating value, 2,540 kcal/kg was calculated on average when the LHVw formula was applied, which is approximately 116 kcal/kg higher than the average design standard of 2,424 kcal/kg. The energy recovery rate was calculated as 96.9% on average based on production and 67.5% based on effective consumption, and the analysis shows that approximately 29.4% energy can be used.

• Journal of Korea Society of Waste Management
• /
• v.35 no.8
• /
• pp.762-769
• /
• 2018

This study was carried out to examine the improvement plan by analyzing the characteristics of imported wastes, operation rate, and benefits of energy recovery for incineration facilities with a treatment capacity greater than 50 ton/day. The incineration facility capacity increased by 3,280 tons over 15 years, and the actual incineration rate increased to 2,783 ton/day. The operation rate dropped to 76% in 2010 and then rose again to 81% in 2016. The actual calorific value compared to the design calorific value increased by 33.8% from 94.6% in 2002 to 128.4% in 2016. The recovery efficiency decreased by 29% over 16 years from 110.7% to 81.7% in 2002. Recovery and sales of thermal energy from the incinerator (capacity 200 ton/day) dominated the operation cost, and operating income was generated by energy sales (such as power generation and steam). The treatment capacity increased by 11% to 18% after the recalculation of the incineration capacity and has remained consistently above 90% in most facilities to date. In order to solve the problem of high calorific value waste, wastewater, leachate, and clean water should be mixed and incinerated, and heat recovery should be performed through a water-cooled grate and water cooling wall installation. Twenty-five of the 38 incineration facilities (about 70%) are due for a major repair. After the main repair of the facility, the operation rate is expected to increase and the operating cost is expected to decline due to energy recovery. Inspection and repair should be carried out in a timely manner to increase incineration and heat energy recovery efficiencies.

• Analytical Science and Technology
• /
• v.19 no.2
• /
• pp.172-180
• /
• 2006

This study was performed to establish new methods for hazardous substances and to develop an analytical method in specified wastes for preventing the environmental pollution caused by hazardous wastes. Therefore, the trends of international management, regulatory criteria, and items of hazardous wastes in various countries were investigated. Based on this study, target priority of new hazardous substances in specified wastes was established. An analytical method was developed using the waste standard reference materials of sludge, oil, bottom ash, etc., which contain the new hazardous substances (Ba, Be, Cr(VI), F, Ni, Sb, Se, and V). A total of 37 waste samples from the representative facilities, which are emitting new hazardous substances, were analyzed.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.15-19
• /
• 2006

The meat consumption produces a lot of bone waste everyday. Dumping bone waste without treatment results into environmental hazards. Conventional treatment by pyrolysis is slow, inefficient and produces hazardous by-products. In the work, an investigation of bone waste incinerated using thermal plasma technology is presented. A high temperature arc plasma torch operated at 33 kW was employed for the experiments. Bone waste was incinerated to remove the infectious organic matter and to vitrify the inorganic matter using plasma torch. Bone waste was reduced its 2/3 weight after the treatment. The process was highly efficient, economical, convenient, and fuel free. This method could be used as an alternative method for disposal of bone waste, small infectious animals, hazardous hospital waste, etc.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.4
• /
• pp.427-436
• /
• 2003

This study is to establish a waste bed combustion model that can be available to assist the design of incinerators for efficient operation control of municipal waste incinerators. An unsteady one -dimensional bed combustion modeling was developed which incorporates the various sub-process models and solves the governing equations for both gases and solids in the waste bed combustion phenomena. The combustion characteristics and the properties of the combustion gas released from the bed were investigated by using a developed model. Besides, a sub-model which predicts the formation and destruction of nitrogen oxides in the waste bed was also developed as a post-processor for the waste combustion model. It is found that the reduction rate of nitrogen oxides is enhanced in the char layer.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.528-535
• /
• 2000

Solid waste incinerator is expected to become widely used in Korea. The incineration of solid waste produces large quantities of bottom and fly ash, which has been disposed of primary by landfilling. However, as landfills become undesirable other disposal method are being sought. In this study, an experimental research is conducted to determine the geotechnical properties of municipal solid waste incinerator fly ash(MSWIF) in order to evaluate the feasibility of using the material for geotechnical applications. Basic pysicochemical characteristics, moisture-density relationship, strength, permeability, and leaching characteristics are examined. The results of MSWIF are compared to other MSWIF and coal fly ash which are used as construction material. In addition, the effectiveness of cement stabilization is investigated using various mix ratios. The result of stabilized mixes are compared to the unstabilized material. Cement stabilization is found to be very effective in reducing permeability, increasing strength, and immobilizing heavy metals. This results indicate that MSWIF with cement stabilization may be used effectively for geotechnical application.

• Journal of Environmental Science International
• /
• v.8 no.2
• /
• pp.183-187
• /
• 1999

The purpose of this study is providing basic data to control the air pollutants from solid waste incinerator. Incinerating the waste wood, the electrostatic precipitator had the best collection efficiency. The leather incineration had the same collection efficiency as synthetic resin incineration. And the coarse particle collection efficiency was high. As you know in correlation of leather incineration. pollutants produced a from incinerator are mostly fine particles. If the scrubber used only in the process produced a lot of fine particles. It is adequate to use the above control devices, together with high efficiency collector like bag-filter. To select the adequate control devices, it is required to investigate the size distribution before establishing control devices.

• Journal of Environmental Science International
• /
• v.11 no.6
• /
• pp.543-551
• /
• 2002

A Numerical simulation on the thermal flow performance was carried out to propose the incinerator type for the domestic refuses and to investigate the design factor and operating conditions. The SSTI(Standard Stoker Type Incinerator) proposed in this study was modified from the type with central f)ow. It has the characteristics of good mixing between refuse and hot combustion gas in primary combustion chamber and between unburned gas inflowing and secondary air jet in secondary chamber. By predictive results, the SSTI was no recirculation zone in secondary chamber so that mixing time was increased with high residence time. It has good characteristics of combustion and low emission. Parametric screening studies have been understood with phenomenon of combustion in incinerator.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1996.10b
• /
• pp.85-90
• /
• 1996

석탄 직접연소의 신기술인 Cyclone 연소기술은 환경오염저감 기술증의 하나로서, 고온 연소로 인해 회분이 연소실 내부에서 용융, 제거된 후 고온의 청정연소가스만 보일러로 유입된다. 또한 연소기의 fuel-rich 연소조건하에서 생성된 고온의 불완전연소가스는 보일러 입구에서 충분한 재연소공기를 공급함으로서 완전연소시킬 수 있으므로 적은 시설투자 비용으로 기존 오일이나 가스용 보일러를 석탄용으로 전환이 용이할 뿐만 아니라 이러한 다단 연소방식을 채택하여 NOx 제어도 가능하다는 이점이 있다. Cyclone 연소기술의 개발은 석탄의 청정연소 뿐만 아니라 그 기술을 토대로 석탄가스화, MHD 발전, 가연성 폐기물 소각등에도 활용할 수 있다. 따라서 국내 기술자립을 위해 실험용 Cyclone 연소기를 설계, 제작 및 연소실험을 수행한 결과, Peco-semi탄을 연료로 공급량 약 30 kg/hr, 공기비 약 1.0 일 때 탄소전환율은 약 95% 이며 회분제거율은 약 70%임을 확인할 수 있었다.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1993.10a
• /
• pp.68-73
• /
• 1993

여과포에 의한 분진 포집기술은 다른 분진포집기술에 비해 가장 우수한 집진성능을 나타낼수 있는 집진기술로서 최근에 와서는 분진발생공정, 연소설비 및 폐기물 소각설비의 중금속 물질, 유해 기체 및 분진의 동시포집 적용 등 광범위한 산업분야에 적응되어 운전되고 있다. 배출기체의 악조건과 습도가 다량 함유된 조건에서는 여과포 집진장치의 적용이 어렵다고 생각되고 있지만, 처리 기체의 조건 및 포집분진의 특성에 적합한 여과포의 개발과 탈진방식(cleaning method)의 개선으로 인해 해결이 가능하게 되었다. 또한 여과포에 의한 분진포집기술은 장치를 통과하는 배출기체의 속도가 다른 집진기술에 비해 느려 여과포 면적이 상대적으로 넓어져서 장치의 설치면적이 많이 소요된다는 단점이 있으나, 여과포를 원간으로 봉재하여 서로 접근시켜 많은 갯수를 다단으로 배치함과 동시에 연속탈진시스템(on-line cleaning)을 채택함으로써 장치에 소요되는 면적을 최소한으로 줄이려는 연구가 계속되고 있다. 대체적으로 여과포에 의한 분진포집기술의 산업체 적용에서 장치의 압력손실은 약 100 - 100 $mmH_2O$ 정도의 범위가 대부분이고 분진 포집효율은 거의 99.9%에서 99.99% 정도 달성이 가능하다[1,2,3].