• Railway Journal
• /
• v.14 no.5
• /
• pp.41-45
• /
• 2011

• Journal of the Korean GEO-environmental Society
• /
• v.6 no.3
• /
• pp.25-34
• /
• 2005

The governing design point of shallow foundation is not its bearing capacity but its settlemen and N-value by the SPT is one of the key parameters for settlement estimation. However, if the N-value is more than 50/30, such as 50/10 or 50/20, the N-vlaues are not blow count of 30cm depth penetration. In these cases, the estimated settlements have big difference with the measured values because the applied maximum N value for the settlement estimation is 50. Therefore, in this study, the modified method for N-value estimation is suggested. The settlements by four methods, which are based on Elastic Theory with application of modified N-value, are compared with the Origina Plate Load Test data. The same comparision was carried out with another seven Empirical Methods. The result of this study showed that the error range of settlement is decreased from 260.4~2136.5% to 20.3~272.7%. Among four methods which are based on Elastic Theory, the original method by Elastic Theory is the most accurate with the application of modified N-value. Among Empirical Methods, Terzaghi-Peck's(1948, 1967) modified method 1 is the most accurate with the application of modified N-value. The differences between the original method by Elastic Theory and Terzaghi-Peck's(1948, 1967) modified method 1 are neglectable.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.10
• /
• pp.31-40
• /
• 2022

This study compares elastic moduli calculated using two stiffness testing methods with different strain ranges to evaluate the stress-settlement characteristics of foundation support layers. Elastic moduli were calculated by the soil stiffness gauge (SSG) in the micro-strain range and the plate load test (PLT) in the medium strain range. To apply the elastic moduli obtained by the two testing methods with different strain ranges to the design and construction of foundation soils, the correlation between each measurement value should be identified in advance. As a result of the comparative analysis of the elastic moduli calculated using the two methods in weathered soil and rock, which are representative support layers in Korea, the calculated elastic moduli differed depending on the types of soil and stress conditions. For various soil types, the static elastic modulus obtained by the PLT was reduced by 56% because of the difference in the strain level of the test compared with the dynamic elastic modulus obtained by the SSG. Therefore, the results show that it is necessary to apply corrections to the stress distribution, stress level, and dynamic effect according to the ground stiffness to effectively use the SSG instead of the PLT.

• 한국도로학회:학술대회논문집
• /
• 2008.10a
• /
• pp.485-491
• /
• 2008

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.11a
• /
• pp.69-72
• /
• 1989

구형의 압자를 유리평판 위에 올려 놓고 미끄럼 시험을 할 때 하중이 임계치보다 크면 유리평판 표면에 소위 "semi-circular cone-crack(SCCC)"들이 형성된다. 그리고 이 SCCC형성에 필요한 임계하중은 유리의 강도에 의하여 결정된다. 한편 소석회 유리에서 크기가 작은 이온인 $Na^+$를 큰 이온인 $K^+$로 대치시켜주는 경우 시편표면에 잔류압축응력이 생성되어 강도가 크게 증가한다. 따라서 유리의 내마모성도 이온교환을 하면 크게 향상될 것임을 예측할 수 있다. 본 연구의 목적은 이 예측을 실험적으로 확인하는 것이다. 확인하는 것이다.

• International Journal of Highway Engineering
• /
• v.13 no.1
• /
• pp.33-40
• /
• 2011

The resilient modulus which is presented mechanical properties of compacted subbase material is the design parameter on the Mechanistic - Empirical pavement design guide. The compaction control method on the Mechanistic - Empirical pavement design guide will be the way to confirm whether the in-situ elastic modulus measured after the compaction meets the resilient modulus which is applied the design. The resilient modulus in this study is calculated by the neural network suggested by Korea Pavement Research Program, and degree of compaction as the existing compaction control test and plate bearing capacity test(PBT) was performed to confirm whether the in-situ elastic modulus is measured. The Light Falling Weight Deflectometer(LFWD) is additionally tested for correlation analysis between each in-situ elastic modulus and resilient modulus, and is proposed correlation equation and test interval which can reduced overall testing cost. Also, the subbase compaction control procedure based on the in-situ elastic modulus is proposed using the in-situ PBT and LFWD test result.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.142-143
• /
• 2021

The general ground conditions in Korea are distributed in order of fill, deposit soil, weathered soil, weathered rock, soft rock. The fill soil and deposit soil located at the top have relatively low strength compared to the lower layer, and they are sometimes classified as soft ground according to the standard penetration test results. In this study, the PF method, a ground improvement method, was applied to the soft layer, a large plate load test was conducted on the improved ground, and the results were reviewed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.53-57
• /
• 1993

굽힘 가공(Bending Process)은 원통형의 다이(die)등을 이용하여 평판형 금속 판재에 프레스 하중을 가하여 임의의 굽 힘 형상을 영구적으로 만드는 가공법으로 소성가공을 하고 있는 대부분의 산업현장에서 널리 쓰이는 가공법 중의 하 나이다. 본 연구에서는 특수 목적이 대형구조물 혹은 대형차체에 주로 사용되어지는 고장력 후판을 대상으로 하여 여러종류의 굽힘각도에 따른 가공성 시험을 수행하고, 굽힘가공부위에서 채취한 시험편에 대한 기계적 물성시험을 통하 여 가공전의 모재와 비교, 분석하므로써 적절한 굽힘 가공조건 및 굽힘가공이 가능한 허용각도등을 결정할 수 있도록 하였다.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.10
• /
• pp.61-74
• /
• 2022

Considering that the number of cases in which a structure foundation is located on weathered rock has been increasing recently, for adequate design bearing capacity of a foundation on weathered rock, allowable bearing capacities of such foundations in geotechnical investigation reports were studied. With reference to the study results, the allowable bearing capacity of a foundation on weathered rock was approximately 400-700 kN/m², with a large variation, and was considered a conservative value. Because the allowable bearing capacity of the foundation ground is an important index in determining the foundation type in the early design stage, it can have a significant influence on the construction cost and period according to the initial decision. Thus, in this study, six large-scale plate-bearing tests were conducted on weathered rock, and the bearing capacity and settlement characteristics were analyzed. According to the test results, the bearing capacities from the six tests exceeded 1,500 kN/m², and it shows that the results are similar with the one of bearing capacity formula by Pressuremeter tests when compared with the various bearing capacity formula. In addition, the elastic modulus determined by the inverse calculation of the load-settlement behavior from the large-scale plate-bearing tests was appropriate for applying the elastic modulus of the Pressuremeter tests. With consideration of the large-scale plate-bearing tests in this study and other results of plate-bearing tests on weathered rock in Korea, the allowable bearing capacity of weathered rock is evaluated to be over 1,000 kN/m². However, because the settlement of the foundation increases as the foundation size increases, the allowable bearing capacity should be restrained by the allowable settlement criteria of an upper structure. Therefore, in this study, the anticipated foundation settlements along the foundation size and the thickness of weathered rocks have been evaluated by numerical analysis, and the foundation size and ground conditions, with an allowable bearing capacity of over 1,000 kN/m², have been proposed as a table. These findings are considered useful in determining the foundation type in the early foundation design.

• The Journal of the Acoustical Society of Korea
• /
• v.12 no.1
• /
• pp.12-19
• /
• 1993

진동시험 동안 구조물은 진동시험기로부터 높은 진동에너지를 받게 되는데 공급되는 에너지를 시험물에 전달하기 위해서는 시험물에 따라 다양한 종류의 진동시험치구가 필요하게 된다. 이중에서 T-형상 진동시험치구는 진동시험축에 대해 3방향으로 시험물을 설치할 수 있고, 형상이 간단하며, 또한 값이 저렴하므로 많은 설계자들은 T-형상 치구를 설계하여 사용한다. 그러나 이 치구는 수직판이 어떤 주파수에서 평판처럼 공진현상을 일으키기 때문에 동역학적으로 설계하기가 어렵다. 본 논문에서는 진동시험치구의 기능을 향상시키기 위해 모우드 시험(Model Testing)기법을 사용하는 방법과 시험결과를 근거로 설계변경을 위해 수직보강판, 수평보강판, 그리고 천연 고무패드를 사용하여 이것들이 치구의 동특성에 미치는 영향을 기술하며 그 결과를 치구설계 때 응용 가능하도록 한다.