• 한국분무공학회지
• /
• 제27권1호
• /
• pp.26-35
• /
• 2022

Electrospray is a method of atomizing fluid using high voltage supply and capable of generating continuous flow and coherent size of droplets. Electrical system and properties of fluids has enabled electrospray to have various spray modes. However, its studies have been confined only in Cone jet, which is more stable and easier to manipulate droplets' size than other spraying modes. Therefore, it is necessary to investigate and compare other spraying modes based on experimental parameters and physical properties of fluids. This research paper identified nine different spray modes. It was found out that Sauter Mean Diameter (SMD) is proportional to flow rate of fluids and maximum difference among spray modes was 1.7 times. On the other hand, SMD standard deviation had low variations on specific flow rates of fluids. Pulsed jet mode recorded the largest SMD standard deviation, while Spindle recorded the lowest.

• 에너지공학
• /
• 제24권1호
• /
• pp.132-136
• /
• 2015

바이오디젤은 재생가능한 친환경적인 연료로서 화석연료의 대체에너지로 수송분야에서 각광받고 있다. 따라서 바이오디젤의 사용량은 향후 꾸준히 증가할 것으로 보이며, 이에 대한 연구가 필요하다. 따라서 본 연구에서는 순수 디젤 대비 바이오디젤이 질량기준으로 0%, 5%, 20%, 50%, 100% 혼합된 연료를 사용하여 분무 및 연소실험을 진행하고, 분무각, 평균 입경, 열발생율 등의 특성을 도출하였다. 실험 결과, 바이오디젤의 혼합률이 증가할수록 연료의 점도 및 밀도가 증가하여 분무각과 특정 위치에서의 평균 입경이 작아지는 것을 확인할 수 있었으며, 바이오디젤의 함산소 특성으로 인해 초기 연소가 촉진되며, 이로 인해 연소 종료 시점이 앞당겨 지는 것을 볼 수 있었다.

• 생물환경조절학회지
• /
• 제7권4호
• /
• pp.298-310
• /
• 1998

본 연구에서는 온실냉방용 포그시스템 설계시 필요한 기초자료 확보를 위하여 경상대학교내 실험온실에 설치한 3종류의 노즐을 중심으로 분무특성에 대해 실험을 수행하였다. 그 결과 단위 노즐당 분무량은 분무압력이 증가할수록 증가하나, 각 노즐에서 공히 분무압력의 증가에 따른 분무량의 증가율이 일정하지 않았다. 노즐의 유형 I, II, III형별로 전체 실험분무압력에서 최소입경은 각각 약 1.7~2.5$\mu$m, 1.7~2.2$\mu$m 및 1.7~2.2$\mu$m이었고, 최대입경은 각각 약 44~60$\mu$m, 52~71$\mu$m 및 45~61$\mu$m이었으며, 평균입경은 각각 약 23~38$\mu$m, 19~24$\mu$m 및 17~25$\mu$m범위에 있었다. 그리고 노즐 I, II, III 별로 분무입경이 가장 양호하다고 판단된 분무압력은 각각 70kg/$\textrm{cm}^2$, 30kg/$\textrm{cm}^2$ 및 30kg/$\textrm{cm}^2$이었으며, 그 때의 분무량은 각각 124mL/min, 103mL/min 및 84mL/min정도였고, 평균입경은 각각 약 22.6$\mu$m, 21.8$\mu$m 및 20.6$\mu$m정도였다. 또한 전체 입경분포에서 30$\mu$m이하가 차지하는 비율은 노즐(I, II 및 III)별로 각각 95.4%, 85.7%, 79.0%정도였으며, 비교적 입자가 큰 40$\mu$m이상이 차지하는 비율은 각각 0.2%, 1.28% 및 1.67%정도였다. 그러나 이들 노즐들의 분무입자 크기는 대부분 포그의 한계입경인 50$\mu$m이하에 속하였다.

• 동력기계공학회지
• /
• 제2권1호
• /
• pp.25-30
• /
• 1998

In order to investigate the droplet size distribution and Sauter Mean Diameter in a ultra high pressure diesel spray, fuel was injected with ultra high pressure into the environments of high pressure and room temperature by an Electronic Hydraulic Fuel Injection System. Droplet size was measured with the immersion liquid sampling technique. The immersion liquid was used a mixture of water-methycellulose solution and ethanol. The Sauter Mean Diameter decreased with increasing injection pressure, with a decrease environmental pressure (back pressure) and nozzle diameter. Increasing the injection pressure makes the fuel density distribution of the spray more homogeneous. An empirical correlation was developed among injection pressure, air density, nozzle diameter and the Sauter Mean Diameter of spray droplets.

• 한국분무공학회지
• /
• 제6권3호
• /
• pp.38-44
• /
• 2001

The effect of four diesel fuels with oxygenated agents fuels on spray properties from plain-orifice atomizer was investigated. The oxygenates evaluated were diglyme, MTBE, DEE and DMM and were blended in weights of 5, 10, 15, 20 and 30% in a baseline diesel fuel. The physical properties such as surface tension, density and viscosity are also measured for each blended oxygenated fuels. It was found that changes in physical properties of fuels considered are enough to influence spray properties, i.e. spray angle, spray tip penetration and mean drop size. Spray properties were measured by PMAS(particle motion analysis system) which is employing a point measurement technology. Spray angle increased with increase in oxygenate content. The effect, however, was not great in the higher blend level. The oxygenated fuels produced more shorter spray tip penetration than diesel fuels. SMD was decreased with the increase in blending percent. SMD for DMM and DEE are represented 10.33 and 3.41% decreasing rates respectively. It was found that changes in spray characteristics of oxygenated fuel were easily large enough to impact pollutant emissions. It was clear from this study that spray characteristics of oxygenated fuel is one of possible cause of reducing pollutant emissions. It was clear from this study that spray characteristics of oxygenated fuel is one of possible cause of reducing pollutant emissions from diesel engines when oxygenated fuels is applied.

• 한국자동차공학회논문집
• /
• 제8권2호
• /
• pp.27-32
• /
• 2000

The main objective of this work is to investigate the effect of ambient conditions on the spray behavior and spray characteristics of high-pressure fuel injector. For this purpose, the effects of ambient pressure and temperature on the spray characteristics have been studied by applying the analysis of visualization system and phase Doppler particle analyzer. In this experiment, the visualization of spray behavior was performed under various ambient gas conditions and injection parameters such as gas temperature, ambient pressure, injection pressure of injector, and axial distance from the nozzle tip. Based on the investigation results, the spray tip penetration and spray width decrease with the increase of ambient gas pressure in the spray chamber. The effects of the spray parameters on the microscopic characteristics of gasoline spray were discussed.

• 한국추진공학회지
• /
• 제12권2호
• /
• pp.48-56
• /
• 2008

액체로켓 예연소기의 산화제 과잉 연소는 매우 어려운 과업이다. 이를 위해서는 작동 조건에서 좋은 혼합특성을 갖는 분사기를 설계하는 것이 무엇보다 중요하다. 따라서 고압환경에서 로켓 산화제 과잉 예연소기용 분사기의 분무특성을 실험을 통해 알아보았다. 분사기는 연료 및 산화제 오리피스, 산화제 스커트로 구성되어있다. 분사기의 분무특성을 알아보기 위해 주위기체압력을 0에서 30kgg/cm2[g]까지 가압하여 분무 가시화, Sauter 평균 입경을 측정하였으며, 액적 크기는 이미지 처리 기법을 이용하였다. 실험결과로부터 로켓 산화제 과잉 예연소기용 분사기의 분무특성을 이해할 수 있었으며, 로켓 산화제 과잉 예연소기 개발에 중요한 자료로 활용될 수 있을 것이다.

• 한국분무공학회지
• /
• 제6권3호
• /
• pp.23-31
• /
• 2001

An experimental study was carried out to understand the spray characteristics of three kinds(kerosene, heating oil & diesel) of hydrocarbon-fuels. Fuel temperature and injection pressure were main variables in the experiment. Fuel Temperature was changed to obtain various levels of fuel viscosity. Spray angle and spray length were measured by using LVS(Laser Vapor Screen) photographs. 1D PDPA system was used to measure droplet size & droplet velocity. In room temperature, spray characteristics of three kinds of fuels were good, especially in case the fuel injection pressure was more than $6Kgf/cm^2$ It was also found that spray characteristics were poor in case fuel kinematic viscosity was more than 5cSt.

• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.177-186
• /
• 1996

A convolution alogorithm combined with Fourier transformation is applied to the tomographic reconstruction of the asymmetric spray structure to identify the local drop size and volume concentration. The line of sight intergrated data from Malvern particle analyzer with multiangular scanning form a basic information for the deconvolution. Linear interpolation is tested to obtain the effect of increasing number of scanning angles. This transformation method predicts well the structure of asymmetric spray. The tehnique can be extended to other line of sight combustion diagnostics.

• 한국분무공학회지
• /
• 제1권2호
• /
• pp.33-41
• /
• 1996

Mixture formation is one of the important factors to improve combustion performance of MPI gasoline engines. This is affected by spray and atomization characteristics of injector. Especially, in the case of EGI system, air-fuel mixing period is too short and formed a lot of fuel-film in the intake manifold and cylinder wall. This fuel-film is not burnt in cylinder, it is exhausted in the form of HC emission. In this paper, spray characteristics such as size distributions, SMD, and spray angle are measured by PMAS, and the fuel-film measuring device is developed specially. Using this device, the amount and distribution of fuel-film which flows into through valve can be measured Quantitatively. As the result of these experiments, the information of optimal spray characteristics and injection condition that minimize the fuel-film can be built up.