• Journal of Adhesion and Interface
• /
• v.8 no.4
• /
• pp.14-22
• /
• 2007

In the present study, the effect of milled glass powder and liquid-type nitrile rubber (NBR) on the thermal stability of phenolic resin and the dynamic mechanical properties of glass braid/phenolic composites has been investigated by means of thermogravimetric analysis and dynamical mechanical analysis. It was found that both milled glass power and NBR filled in the waterborne phenolic resin significantly influenced the thermal stability of phenolic resins and the storage modulus and tan delta of the composites. The presence of glass powder increased the thermal stability of the phenolic resin, whereas the presence of NBR resulted in the weight loss in the specific temperature range. The thermal stability of the phenolic resins without and with the fillers was dependent not only on the cure temperature but also on the cure time. The variation of the storage modulus and tan ${\delta}$ of strip-type glass braid/phenolic composites was also influenced with the introduction of glass powder and NBR to the phenolic matrix as well as by the cure conditions given.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.4 no.2 s.13
• /
• pp.29-34
• /
• 2004

The time to ignition, heat release rate characteristics, and carbon monoxide yield of fiber reinforced and sandwich phenol resin were investigated with cone calorimeter. The fire characteristics of unsaturated polyester, mostly being applied to the existing passenger train, and phenolic resin were compared. DSC & TGA was used to monitor the degree of thermal decomposition and weight loss for the phenolic resin. According to the cone calorimeter data, the time to ignition was shorter, heat release rate, and CO yield was higher as the external heat flux increased. Under the same heat flux, the time to ignition of sandwich type phenolic resin was shorter than that of laminated. The result of comparison between unsaturated polyester and phenolic resin was that phenolic resin was shown to have better fire resistance than unsaturated polyester.

• Journal of Adhesion and Interface
• /
• v.11 no.4
• /
• pp.149-154
• /
• 2010

Interfacial evaluation was investigated for single-carbon fiber/phenolic and carbon nanotube (CNT)-phenolic composites by micromechanical technique and electrical resistance measurement combined with wettability test. Compressive strength of pure phenol and CNT-phenolic composites were compared using Broutman specimen. The contact resistance of CNT-phenolic composites was obtained using a gradient specimen by two and four-point methods. Surface energies and wettability by dynamic contact angle measurement were measured using Wilhelmy plate technique. Since hydrophobic domains are formed as heterogeneous microstructure of CNT in the surface, the dynamic contact angle exhibited more than $90^{\circ}$. CNT-phenolic composites exhibited a higher apparent modulus than neat phenolic case due to better stress transferring effect. Work of adhesion, $W_a$ between single-carbon fiber and CNT-phenolic composites exhibited higher than neat phenolic resin due to the enhanced viscosity by CNT addition. It was consistent with micro-failure patterns in microdroplet test.

• Composites Research
• /
• v.33 no.6
• /
• pp.329-335
• /
• 2020

In this study, the thermo-rheological behaivors of petroleum pitches with different softening points were studied, and a B-stage phenolic resins/petroleum pitches blends were prepared by adding petroleum pitches to the phenolic resins. As a result, the petroleum pitch with different softening points decreased the fluidity of the petroleum pitch as the Quinoline insoluble (QI) content increased and showed the viscous properties of the solid. In addition, the effect of adding petroleum pitches having different softening points on the thermo-rheological properties of phenolic resins was investigated. When petroleum pitch with a high softening point was added, the fluidity of the phenolic resin was reduced, and the hardening behavior was fast. It was possible to control the curing rate and curing behavior of the phenolic resin by adding petroleum pitches of different softening points. Among them, the phenolic resin mixture to which P-Pitch 2 was added has a higher fluidity than other blends under the same curing temperature condition.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.238-242
• /
• 1998

Wood powder filled phenolic resin composites of different composition were prepared and their mechanical properties were investigated for optimum conditions. The composites showed maximum mechanical strength when the phenolic resin content was 45 wt%. Polyurethane prepolymer(PU) was evaluated as a modifier of the phenolic resin composites. Blocking of the isocyanates in the PU with phenol was necessary for homogeneous mixing of raw materials for the components. Maximum mechanical strength of the PU modified composites was observed when the PU content was 5 wt%. It was found that the mechanical strength of the composites cured at $210^{\circ}C$ were higher than those of the composites cured at $150^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.31 no.3
• /
• pp.310-316
• /
• 2020

Terpene-modified phenolic resins were used to improve the tires wet traction related to the driving safety and also rolling resistance related to fuel efficiency. In this work, alpha-pinene, beta pinene, and delta limonene resins, which constitute different basic structures of terpene-modified phenolic resins, were individually added to the tread compounds of tires and their physical properties were compared with those of the alkyl phenol resin compounds. Alkyl phenolic resins showed no significant difference in tangent delta from terpene-modified phenolic resins at 0 ℃, which is related to wet traction, but showed higher tangent delta at 80 ℃, which is related to rolling resistance, indicating smaller fuel efficiency improvement effects. Among the terpene-modified phenolic resins, beta pinene one showed improved wet traction and fuel efficiency compared to those of other resins. Delta limonene resin showed the best wet traction improvement effect, and alkyl phenolic resins showed relatively high tensile strength and abrasion property. All terpene-modified resins exhibited better rolling resistance than those of alkyl phenolic ones so that they can be said to have better fuel efficiency improvement effects and also to improve other properties compared to those of blanks. Terpene-modified phenolic resins could be used when mixing tire compounds referring to the properties of the phenolic resins revealed in this work, which could result in preparing compounds with improved wet traction and rolling resistance.

• Applied Chemistry for Engineering
• /
• v.17 no.4
• /
• pp.357-360
• /
• 2006

In this study, we studied the physical properties and application of PF foam as heat insulating materials. In the experimental results, the density of PF foam showed $0.030g/cm^3$ and the thermal conductivity showed $0.026kcal/m.h.^{\circ}C$. Also, thermal resistance of the prepared PF foam was volatilized about 71.7 wt% when the temperature was $500^{\circ}C$ (1 h). And the chemical structure of PF foam have a closed cell type in the important properties as heat insulating materials. Therefore, it was confirmed that the prepared PF foam had excellent performance as heat insulating materials.

• Korean Journal of Materials Research
• /
• v.7 no.10
• /
• pp.838-844
• /
• 1997

폴리아크릴로나트릴(PAN)계 탄소섬유 및 안정화 PAN섬유를 사용하여 제조한 페놀수지 복합재료의 열주기 산화저항성에 섬유표면의 인산코팅 유.무가 미치는 영향을 조사하였다. 각 복합재료의 열주기 산화저항성은 열중량분석기의 원리를 응용하여, 공기중에서 hot zone과 cold zone을 주기적으로 반복이동하는 열충격조건에 노출되면서 초래되는 복합재료의 중량변화를 측정하여 비교하였다. 시험변수로는 hot zone에 노출된 온도, 시간 및 싸이클횟수를 선정하였다. 이 시험방법은 비교적 단순하며, 작은 크기의 시편으로도 가능하고, 중량변화가 온-라인 모니터에서 직접 감지되므로 데이타의 신뢰성이 \ulcorner다. 각 시험조건에서 인산코팅한 섬유를 사용한 복합재료가 그렇지 않은 재료보다 고온에서의 높은 산화저항성 때문에 우수한 열주기저항성을 보여 주었다. 또한 인산코팅의 존재 여부가 열주기시험 후의 탄소섬유-페놀수지 및 안정화 PAN섬유-페놀수지 복합재료의 미세구조에 미치는 영향을 조사하였다.

• Journal of the Korean Chemical Society
• /
• v.34 no.3
• /
• pp.267-279
• /
• 1990

The adsorption mechanisms of phenols on XAD-2 and XAD-7 resins were studied by using the distribution coefficient(log Kd) measured in the optimum adsorption conditions. It was observed that the Langmuir adsorption isotherm, indicating a molecular size-dependent adsorption, was appropriate for characterizing the adsorption behaviors of phenols on XAD-2 and XAD-7 resins. The adsorption energies of phenols on XAD resins were calculated by Lennard-Jones potential equation. In the calculation of the adsorption energy, the molecular radii and dipole moments of the resins and phenols were calculated by their van der Waals volumes and Debye equation, respectively. The stacking factor (F) were determined from the radio of the equilibrium distance to the stacking distance of molecules. In order to explain the adsorption energy calculated from the stacking factor it was compared with the adsorption enthalpy for each of phenols which was experimentally determined by batch adsorption shake method. It was observed that the adsorption enthalpy of phenolate ions on the XAD resins was likely to be more seriously affected by dispersion interaction than by a dipole or a charge interaction.

• Journal of Adhesion and Interface
• /
• v.12 no.3
• /
• pp.94-98
• /
• 2011

Ballistic property of Heracron/phenol composites was evaluated as a function of polyurethane (PU) type and their loadings. First, prepregs of phenol and polyurethane were prepared by spray coating on Heracron fabric and then they were utilized to prepare composite by varying their ratio. Next, they were consolidated at $150^{\circ}C$ for 25 min at $150kg/cm^2$ pressure and then ballistic property was measured with 1.1 g FSP (22 cal). V50 was evaluated interms of polyurethane type and ratio of phenol/PU prepreg.