• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.299-305
• /
• 2010

In general, the flexible forming die that has been used in the flexible forming process has the identical punch size; hence, its flexibility is relatively low because the range of allowable curvature radii is limited due to the uniform punch tip radius. Hence, a conceptual design of a sectional flexible die is presented for enhancing the flexibility of the forming process. Two punches of different sizes are used to configure the arbitrary forming surface. For a forming region with a relatively large curvature radius, a large punch array block is used; on the other hand, for the forming regions with small curvature radii, a small punch block is used. The cross-sectional profiles are compared with the target shape for evaluating the effectiveness of the process. Consequently, it is confirmed that the sectional flexible die can be used along with a combination of punch blocks of different sizes for manufacturing objective surfaces of complex shapes.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03a
• /
• pp.22-25
• /
• 1999

'There are a lot of process variables, exerted influence on the formability of products, in deep drawing process. Particularly, it is important that the punch and die shape radius of the process variables. Though researches have been performed on the deep drawing of sheet metal forming, like this study, but it is insufficient the actual circumstances that researches for process variables of the non-axisymmetric deep drawing products. In this study, An effect on thickness distribution is grasped as alteration of the punch and die shape radius in the process of non-axisyrnmetric deep drawing products, and then the optimal punch and die shape radius were presented, they were verified by the numerical analysis method (FEM).

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.216-225
• /
• 2023

This paper describes the finite element analysis and die design change of cold heading punching process to increase the cold forging tool life and reduce the tool wear and stress concentration. Through this study, the optimization of punch tool design has been studied by an analysis of tool stress and wear distribution to improve the tool life. Plastic deformation analysis was carried out in order to understand the cold heading process between tool and workpiece stress distribution. Cold heading punch die design was set up to each process with different four types analysis progressing, the cold heading punch dies shapes with combination of point angle and punch edge corner radius shapes of cold forging dies, punch die material properties and frictional coefficient. The design parameters of point angle and corner radius of punch die geometry, die material properties and frictional coefficient were selected to apply optimization with the DoE (design of experiment) and Taguchi method. DoE and Taguchi method was performed to optimize the cold heading punch die design parameters optimization for bolt head cold forging process, it was possible to expect an reduce the cold heading punch die wear to the 37 % compared with current using cold heading punch in the shop floor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.1
• /
• pp.7-12
• /
• 2010

In this work, optimization analysis has been accomplished to find important process factors for realization of vertical wall around holes punched by the punchless piercing process. Taguchi method was used for optimization analysis. Lemaitre damage theory, one of the ductile fracture models, was also adopted to simulate numerically formation of vertical wall. From the results of analysis the most influencing factor that affects the vertical wall has been revealed to be 'Corner Radius of Die'.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.4
• /
• pp.769-776
• /
• 1990

본 연구에서는 소재형상을 미끄름선장법으로 구하고, 이것을 등고컵(cup with uniform height이하 h-uni cup)을 얻을 수 있는 이상적인 소재형상으로 보았으며, 이 로 부터 8각형을 소재로 취할 경우의 최적 모따기 량을 얻고, 또 정사각형 소재도 포 함하여 세가지 소재형상을 대상으로 하여, 광범위한 펀치의 모서리반경에 따른 한계드 로잉비(L.D.R), 유효 컵높이, 드로잉하중, 두께 분포 등을 고찰하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.70-76
• /
• 1999

Recently most of researches for deep drawing process using sheet metal have been performed on the formability of axisymmetric shape but there have not been any concrete reports on the formability of non-axisymmetric shape In addition the conventional shape radius of the punch and die has been determined by the trying-and-error using industrial experimence and post processing test and only approximate shape radius of the punch and die has been determined by the trying-and-error using industrial experience and post processing test and only approximate shape radius of the punch and die has been present So in this study the optimal shape radius of the punch and die in deep drawing process with biaxisymmetric blank shape would be proposed. Through the deep drawing experiment it is found that in order to obtain the optimal products especially shape radius of the punch and die in all processes is very important.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.3
• /
• pp.283-288
• /
• 2012

Ultra-high-strength steels (UHSSs) are widely used for lightweight automobile parts, and the control of springback is very important in sheet-metal forming. The object of this study is to verify the effects of multi-stage forming process parameters for U-channel-type automobile parts made of UHSS. Finite element analysis is carried out to predict the formability and springback. The main parameters considered for the multi-stage forming process are the die angle, die radius, and punch-forming direction. It is shown that multi-stage forming is very effective for reducing springback, and that a small punch-forming angle and die radius reduce springback, whereas the die angle does not have a large effect.

• Composites Research
• /
• v.12 no.5
• /
• pp.31-39
• /
• 1999

Glass-fiber reinforced polymeric composites provide the desitable properties of high stiffness and strength as well as specific weight. Hence, they have become some of the most important materials in several industries. These composites can be grouped into thermoplastic and thermoset composites, with thermoplastic composites having several advantages over thermoset composites in mechanical properties and processing. As a result, the study of the material behavior and forming techniques of such composites has attracted considerable attention in recent years. When the continuous fiber-reinforced polymeric composites are molded by flow molding, the molded parts leads to be nonhomogeneity and anisotropic because of the separation and orientation of fibers. As the characteristics of the products are greatly dependent on the separation, it is very important to clarify the separation in relarion to molding conditions, fiber mat structures and mold geometry. In this study, the effects of the mold geometry and the fiber mat structure on the compression moldability are studied using the cup-type molding.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.04a
• /
• pp.92-95
• /
• 2000

In order to obtain the optimal products in deep drawing process elliptical deep drawing tests were carried out with several shape radii of the punch and die. As parameters on testing shape radii of the punch and die were selected, In addition the conventional shape radii have been determined by trial=and-error using industrial experience and post processing test and only approximate shape radii of the punch and die have been presented. The optimal shape radii of the punch and die in elliptical deep drawing process with biaxisymmetric blank shape are proposed. In this study we suggest the appropriate conditions to be applicable to the catual manufacturing processes through the experiment and finite element method.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.3
• /
• pp.119-126
• /
• 1998

유리섬유 강화 열가소성 복합재료는 고상성형법에 의해 저렴한 가격으로 큰 부피의 제품의 제조에 널리 사용될 수 있어 아주 좋은 전망을 가지고 있다. 그러나 이러한 재료의 성형성이나 재료거동의 특성은 아직 잘 파악되지 않았다. 본 연구의 주안점은 이러한 재료의 단순 굽힘에서의 굽힘성형성을 연구하는데 두었다. 실험에 사용된 재료는 임의의 방향으로 위치한 유리섬유를 중량비로 20 %, 35 %, 40 % 함유한 폴리프로필렌이다 굽힘시험은 75 $^{\circ}C$에서 150 $^{\circ}C$ 사이의 온도에서 25 $^{\circ}C$ 씩 증가하면서 행했고, 편치속도는 2.54 mm/sec와 0.0254 mm/sec에서 행했다. 단순 굽힘시험에서 측정된 굽힘성형성은 해석적 모델로 예측한 결과와 비교하였다. 실험결과와 예측결과가 비교적 잘 일치함을 보였으며, 굽힘성 map으로써 성형 온도와 펀치반경의 좌굴에 대한 효과를 가시화 함은 물론 좋은 성형조건을 선정할 수 있는 좋은 도구로써 나타내었다.