• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.185-190
• /
• 2001

The structure borne noise of the air-conditioner, which degrades the noise quality, is hardly reduced by the general noise treatments. It can be effectively reduced by eliminating the structural vibration which the noise originates from. The rubber vibration isolator prevents the dynamic force induced by the fan driving motor from exciting the chassis structure, which finally reduces the structure borne noise. The dynamic properties of the vibration isolation system such as the natural frequency of the vibration isolation and loss factor of the rubber isolator, need to be experimentally evaluated. In this paper, these dynamic properties were obtained by the resonant method using the impact hammer for 3 types of the isolator specimens. It is known that the isolation natural frequency of the axial direction of the rubber isolator is two times higher than that of the radial direction, and is proportional to the hardness of the rubber specimen.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 추계학술대회논문집; 한국종합전시장, 24 Nov. 1995
• /
• pp.172-178
• /
• 1995

보강평판은 평판에 각종 보강재를 용접등의 방법에 의해서 종방향, 횡방향, 경사 또는 임의의 방향으로 부착시켜 굽힘 및 비틀림 강성을 향상시킨 구조요소이다. 이러한 구조요소는 구조적 필요성이나 경량화 설계에 따라 선박의 deck, 철도 차량, 항공기 및 자동차 등의 각종 구조물에서 부하능력 및 경제성을 증대시키기 위하여 널리 사용되고 있고, 또한 자동차용 오일팬, 가전기기의 케이싱과 모터의 케이싱등에도 사용되고 있다. 최근 현장에서는 이러한 구조물의 진동 감소 및 방진 문제가 큰 관심사가 되고 있다. 본 논문은 정사각형 알루미늄 평판에 +자 형태의 Box Beam 보강재를 편면 보강하고 4변 자유단의 경계 조건을 설정하였다. 보강재는 유한요소 정식화 과정을 통하여 평판 요소에 등가시키고, 2차원의 평판 구조로 보강 평판을 모델링하고 구조해석 프로그램인 ANSYS를 이용하여 해석하였다. 실험은 Impact Test에 의해서 주파수 응답 함수(FRF)를 각 시편에 대해서 구하고 이를 해석의 고유진동수와 비교하였다. 그리고 보강재가 임의의 각도로 평판에 부착되었을 때 고유진동수의 변화와 진동 모드(mode shape)를 분석하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.402-406
• /
• 2000

In the Over-The-Range, the outlet size is limited by the industrial standards. Therefor to enlarge the volume of cavity, the installation height of ventilation fan is become small, the system resistance is higher than before. For that reason, the important design variables such as the diameter of a fan, the scroll expansion angle, etc. which play the significant role on flow rate and noise, are confined. In this study, we made an experiment of the diameter of fans relation to scroll expansion angle and investigated flow rate of the length of fans in enlarged cavity volume of OTR, and then we designed the new scroll to improve the flow rate and noise level. As a result, flow rate increased to 110% compared to current scroll and the blade passing frequency of a fan is disappeared by inclined cut-off shapes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1381-1385
• /
• 2000

In this paper, a guideline of axial flow fan design for noise reduction of refrigerators is p resented. Refrigerators have components which have a role to screen particular frequency air borne-noise which is generated by an axial flow fan set in them. Effective ways to use the particular characteristic of refrigerators are shown in this study. As a result of application of the methods, we reduced the noise of the target systems by more than 3 dB(A) from the viewpoint of air-borne noise produced by the axial flow fan set.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.256-260
• /
• 2013

The fan-shroud plays the important role in cooling down the engine heat by the forced convection. As the fan-shroud is made by injection molding, the unbalance of the fan blades is inevitable, and its low frequency characteristics makes it easy to excite the resonances of the environmental structures. So controlling its vibration, specially the dominant vibration source of unbalance vibration, is one of key factor to improve the sound and vibration quality of the modern vehicles. This paper introduces the plane balancing method, the most appropriate way of controlling the fan-shroud by generating the acceleration orbit measured from 2 accelerometers, and proves its balancing effect by the experiment.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.494-499
• /
• 2005

This paper introduces a study for the noise reduction of a range hood for household. Generally, range hoods have a built-in sirocco fan from which harsh noises are generated. Though the harsh noises have low noise level, these kinds of noises make most of the users nervous. For the purpose of noise reduction, in this study, a perforated plate system is installed in the fan housing of range hood. From the experimental results, it is confirmed that the noise level emitted from the range hood was decreased more than 10dB(A) in all 1/3 octave bands due to the effect of noise reduction by perforated plate systems.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.82-87
• /
• 2000

During the operation, fatigue failures and cracks of duct plate due to excessive duct vibration occurred in the fan-duct systems of fossil fueled boilers. We measured static pressure variation(pressure pulsation) in the outlet, and also measured vibration at the outlet duct of a centrifugal fan. It was found that strong pressure pulsation caused by the inlet vortex occurred in inlet vane of centrifugal fan in the middle range of vane opening. Thus, excessive duct vibration is caused by strong pressure pulsation. In this paper, it is shown that the frequency and amplitude of pressure pulsation depend mainly on vane opening and are compared with duct vibration. Also, effective solution for reducing pressure pulsation and vibration are presented.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.158-165
• /
• 2004

The DC motor in a vehicle may cause noise and vibration because of high speed revolution, which can make a driver feel uncomfortable. There have been various studies attempting to solve these problems, focusing mostly on the causes of and ways to reduce noise and vibration. It is suggested that the noise in a DC motor may be primarily due to interaction between a brush and a commutator. Brush noise, the most common noise in a DC motor, results from a brush bounced from the surface of the commutator, fluctuation of the friction between the brush and the commutator, and the impact on the brush when passing over slots of the commutator. Based on the noise test, one of the most important design parameters was shown to be the roundness of the commutator. As the DC motor is used, the roundness of the commutator gets bigger with subsequent increase of the level of brush noise and vibration. There must be a threshold in order to prevent the brush noise from getting worse. Using the method of CAE is more efficient than the real test for purposes of looking for various design parameters to maintain the roundness of the commutator. In this study, the design process to reduce the brush noise is presented with the use of a computer model. The design parameters to reduce the brush noise and vibration are proposed by using FEM. The design parameters are used to reduce the noise and vibration of a DC motor and it is verified with the test results on a fan DC motor in a vehicle. This method may be applicable to various DC motor.

• 한국유체기계학회 논문집
• /
• 제6권4호
• /
• pp.14-20
• /
• 2003

In this study an analysis of the flow characteristics in three types of turbo-fans for a vacuum cleaner was performed by using CFD. The characteristics of three models calculated for various rotating speed for flow rates are obtained and compared with measured data. The mixing plane approach is applied to compute the flow between impeller and diffuser. The results show that the model that is modified to reduce fan noise gives stable flow characteristics in operating range than the original model, with both models show similar performance characteristics at the range of high flow rate. Since in the modified model it takes much longer for an impeller blade to pass a diffuser blade than in the original model, and the peak pressure at BPF can be relieved, it is anticipated that the modified model give much lower noise level with similar performance than the original one, which remains to be verified by unsteady computation and measurements. The good agreement between the predictions and measurement results confirms the validity of this study.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.631-634
• /
• 2002

The study of the flow characteristics in two types of turbo-fans for a vacuum cleaner was performed in a previous study. In present study an analysis of a new modified model to reduce fan noise was performed by using CFD. The characteristics of three models calculated for various rotating speeds and flow rates are obtained and compared with available measured data. The results show that the modified model gives stable flow characteristics in operating range than the original model, while both models show similar performance characteristics at the range of high flow rate. Since in the modified model it takes much longer for an impeller blade to pass a diffuser blade than in the original model, and thus the peak pressure at BPF can be relieved, it is anticipated that the modified model gives much lower noise level with similar performance than the original one, which remains to be verified by unsteady computation and measurements.