• 신재생에너지
• /
• 제3권4호
• /
• pp.3-7
• /
• 2007

Graphite/polymer composite bipolar plates for PEMFC are successfully developed, and their typical properties are superior to commercially available ones. Thermal property of the developed bipolar plate was evaluated by dynamic mechanical analyzer, and the results were compared to commercial ones. The specimens were immersed into the deionized water bath at $80^{\circ}$... for 1500hrs to evaluate dimensional stability and durability. Dimension, weight of the specimens as well as extraction conductivity was measured as each 500hrs. Fully molded bipolar plates without any machining or milling were also prepared using a specially developed mold, and they were applied to the fuel cell performance test. Results were compared to the machined commercial bipolar plate.

• 대한안전경영과학회지
• /
• 제2권4호
• /
• pp.177-186
• /
• 2000

The molten carbonate fuel cell has conspicuous features and high potential in being used as an energy converter of various fuels to electricity and heat. However, the MCFC which use strongly corrosive molten carbonate at $650^{\circ}C$ have many problem. Systematic investigation on corrosion behavior of Fe/20Cr/Ti has been done in (62+38)mol % (Li+K) $CO_3$ melt at 923K by using. steady state polarization and electrochemical impedance spectroscopy method. It found that the corrosion current of these Febased alloys decreased with increasing Ti content, and this attribute to the formation of $LiCrO_2$ layer at the surface.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.331-334
• /
• 2009

Currently, the bipolar plates are fabricated mainly from graphite materials. However, metal bipolar plate are getting most attractive due to their good feasibility of mass production and low cost. In this study, metal bipolar plates for fuel cell Vehicles were developed with a concept based on the straight flow patterns to minimize the pressure drop and spring back. And molded gasket apply to the bipolar plate for improve sealing performance. Results show that the metal bipolar plate have a high potential to replace for graphite materials in fuel cell application.

• 신재생에너지
• /
• 제4권1호
• /
• pp.31-36
• /
• 2008

Stainless steels have been widely considered as metallic bipolar plates, due to their passive surface film, which is good for corrosion resistance. However, the high resistivity of the passive film increases interfacial contact resistance between the bipolar plates and the electrodes. Stainless steels thermal spray coated with a mixture of tungsten carbide and stainless steel powders showed that the coated layer safely combined with the matrix but they suffered many internal defects including voids and cracks. Many cracks were formed in the coated layer and the interface of the matrix and the coated layer during the rolling process. The coated and rolled stainless steels showed lower interfacial contact resistance and corrosion resistance than bare stainless steel because of low resistivity of tungsten carbide and numerous defects, which caused crevice corrosion, in the coated layer.

• 신재생에너지
• /
• 제3권1호
• /
• pp.75-82
• /
• 2007

Aluminum was used as metallic bipolar plate material to reduce a stack weight. The functional materials such as conductive material, Au and nonconductive material, PTFE [polytetrafluoroethylene] were coated on the bipolar plate to enhance electrical contact and corrosion prevention in PEMFC. The active area of bipolar plate is divided into the top layer part that electric current mainly passes, and the bottom layer part that gas and water pass. The bottom layer part in the flow channel needs not to have electrical conductivity because it doesn't pass electric current directly. In this reason, Au on the top layer and PTFE on the bottom layer were coated to apply high electrical conductivity and/or good corrosion resistance. Although the single cell performance using Au-PTFE/Al bipolar plate was shown 78% in comparison with that of graphite, specific power of Au-PTFE/Al bipolar plate(0.4 W/g) was twice as much as graphite bipolar plate.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.92.1-92.1
• /
• 2011

고분자 전해질 연료전지 (PEMFC)의 핵심 부품 중의 하나인 Bipolar Plate (분리판)을 제조하기 위해서 고분자/그라파이트 복합재료를 사용하였다. 고분자 매트릭스로는 경화시 뛰어난 화학적, 기계적 특성을 갖는 에폭시를 채택하였고, 전기 전도성을 부여하기 위해 그라파이트를 도입하였으며, 에폭시 수지의 내충격성을 향상시키기 위해서 Carbon Fiber를 채택하였다. 에폭시 분말과 그라파이트 분말, 그리고 1cm 정도의 길이를 갖는 Carbon Fiber을 믹서에 넣고 균일하게 혼합하였다. 이 혼합물을 이형제 처리된 몰드에 주입하고, Hot Press를 사용하여 가열, 가압 ($150^{\circ}C$, 4 ton/$cm^2$, 2시간)하면서 경화시켰다. 일정 비율로 고정된 에폭시/그라파이트 계에 Carbon Filber의 혼합 비율을 변화시키면서 전기적, 물리적 성질의 변화를 연구하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.166-168
• /
• 2007

고분자 전해질 연료전지는 다수의 단위 cell을 적층하여 stack을 형성하게 되며, 각 단위 cell 은 분리판과 MEA 사이에 gasket을 장착하게 된다. 이때 장착된 gasket은 분리판과 MEA사이의 일정한 gap을 유지하여 가스를 균일하게 분배되도록 할 뿐만 아니라, 가스 유출을 막는 sealing 재(材)로서의 역할을 한다. 따라서 고분자 전해질 연료전지의 성능확보를 위해서는 내구성 및 가스 기밀성이 우수한 gasket 개발이 무엇보다 중요하다. 본 연구에서는 이러한 gasket 물성을 만족시킬 수 있는 고분자 전해질 연료전지용 gasket을 개발하고자 하였으며, 이를 검증하기 위하여 가혹 조건에서 실험을 수행하였다. 그 결과 종래의 gasket 보다 열적, 화학적 및 가스기밀성 변에서 우수한 고분자 전해질 연료전지용 gasket을 얻을 수 있었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.146-149
• /
• 2007

The 2-step manufacturing method consisting of preforming and stamping processes was developed to manufacture composite bipolar plates for PEMFCs. The preform was composed of expanded graphite, graphite flake and phenol resin. Precuring conditions were optimized by checking the electrical conductivity, flexural strength and microstructure. Precuring temperature ($100^{\circ}C$) slightly above the melting point of phenol powders ($90^{\circ}C$) induced moderate curing, but also prevented excessive curing. Preforms utilizing the tangled structure of expanded graphite were easily fabricated at low pressure of 0.07-0.28MPa. The proper precuring time, 5min, was determined to fabricate the preform stably because insufficient and excessive precuring deteriorated the flexural strength of composite bipolar plates.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.150-152
• /
• 2007

직렬로 연결 된 다층의 단위전지 집합으로 구성되는 고체 고분자 연료전지의 적층전지는 에서 발생 할 수 있는 단위전지 간 전압손실과 압력구배를 최소화하기 위해 적층전지 내의 단위전지 외에 부품 및 재료를 추가하여 전압손실과 압력구배를 줄이는 방법에 대한 연구를 진행하였다. 체결압 구배를 최소화하기 위해 부드러운 층으로 이루어진 외곽부분과 딱딱한 층으로 이루어진 중심부를 가지는 필름을 전류집합체 뒤쪽에 첨가하였고， 분리판과 전류집합체 사이에서 발생 할 수 있는 전압손실을 방지하기 위해 높은 전기 전도성을 가지며, 평활도를 유지 할 수 있는 재료로 구성 된 복합층을 전류집합체와 분리판 사이에 첨가하였다. 압력구배 측정 및 다층전지 성능테스트 중 단전지간 전압손실을 측정하여 기 제작 된 첨가층들에 대한 영향의 정도를 파악하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.320-323
• /
• 2006

A numerical study is made of a manifold and bipolar plate in polymer electrolyte fuel cells, the aim of the present study is to describe the characteristics of flow pattern In manifold and bipolar plate. The present work shows that the flow pattern in the bipolar plate is affected by the penetration flow through GDL characterized by clamping pressure and GDL intrusion in to a channel area. Manifold geometry also affects the flow distribution. The recirculation flow by bent duct destroy even distribution In manifold, the present work shows that corner rounding can improve the manifold performance.