• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.1
• /
• pp.15-21
• /
• 2004

It is possible to detect flaws in pipelines without interruption using all EMAT transducer because it is a non-contact transducer which can transmit ultrasonic waves into specimens without couplant. And it ran easily generate guided waves desired in each specific problem by altering the design of coil and magnet. In the present work, EMAT systems have been fabricated to generate surface waves, and selectively the plate wave of $A_1\;or\;S_1$ mode. The surface wave of 1.5MHz showed a good signal-to-noise ratio without distortion in its propagation along a pipeline, while the $S_1$ mode of 800kHz and the $A_1$ mode of 940kHz were distorted according to their dispersive properties. The wider the excitation pulse becomes, the better the mode selectivity of the plate waves becomes. A pipe of 256mm inner diameter and 5.5m thickness with 5 flaws was used for comparing the flaw detectability among the modes under consideration.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.4
• /
• pp.398-405
• /
• 2001

The rivet joint has typical structural feature that can be initiation site for the fatigue crack due to the combination of local stress concentration around rivet hole and the moisture trapping. From a viewpoint of structural assurance, it is crucial to evaluate the size of crack around the rivet holes by appropriate nondestructive evaluation techniques. Lamb wave that is one of guided waves, offers a more efficient tool for nondestructive inspection of plates. The neural network that is considered to be the most suitable for pattern recognition has been used by researchers in NDE field to classify different types of flaws and flaw sizes. In this study, clack size evaluation around the rivet hole using the neural network based on the back-propagation algorithm has been tarried out by extracting some features from the ultrasonic Lamb wave for A12024-T3 skin panel of aircraft. Special attention was paid to reduce the coupling effect between the transducer and the specimen by extracting some features related to time md frequency component data in ultrasonic waveform. It was demonstrated clearly that features extracted from the time and frequency domain data of Lamb wave signal were very useful to determine crack size initiated from rivet hole through neural network.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.1
• /
• pp.18-24
• /
• 2006

Reactor core and internal structures of a liquid metal reactor (LMR) can not be visually examined due to an opaque liquid sodium. The under-sodium viewing technique by using an ultrasonic wave should be applied far the visual inspection of reactor internals. In this study, an ultrasonic waveguide sensor with a strip plate has been developed for an application to the under-sodium viewing technique. The Lamb wave propagation of a waveguide sensor has been analyzed and the zero-order antisymmetric $A_0$ plate wave was selected as the application mode of the sensor. The $A_0$ plate wave can be propagated in the dispersive low frequency range by using a liquid wedge clamped to the waveguide. A new technique is presented which is capable of steering the radiation beam angle of a waveguide sensor without a mechanical movement of the sensor assembly The steering function of the ultrasonic radiation beam can be achieved by a frequency tuning method of the excitation pulse in the dispersive range of the $A_0$ mode. The technique provides an opportunity to overcome the scanning limitation of a waveguide sensor. The beam steering function has been evaluated by an experimental verification. The ultrasonic C-scanning experiments are performed in water and the feasibility of the ultrasonic waveguide sensor has been verified.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.5
• /
• pp.458-465
• /
• 2009

In general, ultrasonic guided wave techniques that used for an evaluation of the internal defect have been applied without considering energy loss. It can be found out that the significant attenuation is observed in the signal of structure with defect by the scattering and absorption. Even in the signal acquired from defect-free structure, this attenuation can be also significant. Therefore, it is very essential to determine the Lamb wave propagation characteristics depending on modes because the dispersibility of Lamb wave can be easily influenced by the attenuation effect with frequency and thickness. For this reason, changing the propagation distance, attenuation coefficient of each Lamb wave mode needs to be investigated by the contact pitch-catch method with PZT(piezoelectric) sensors. In this paper, the experimental attenuation coefficient is measured by choosing the following three different variables; mode, thickness and plate materials. As a result, experimental attenuation coefficient is obtained as the function of variables.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.283-287
• /
• 2001

본 논문에서는 3D Ray Tracing 편파특성 예측 시뮬레이터를 개발하고 초고속 옥내 무선환경에서의 원형편파 우수성을 시뮬레이션을 통하여 확인하였다. 제안된 3D Ray Tracing 기법을 이용하여 시뮬레이션 한 결과 기수회의 반사파가 수신기에서 수신되지 않는 원형판파의 특성 때문에 다중경로 페이딩을 현저히 감소시킬 수 있음을 확인하였다. 또한, 옥내 가시거리(LOS) 및 비가시거리(NLOS) 환경에서의 원형편파를 이용한 페이딩 경감효과는 수직 및 수평견파나 편파다이버시티보다 우수함을 알 수 있었고, DS-CDMA 시스템을 이용한 경우에 있어서도 원형편파가 보다 우수한 BER 성능을 나타냄을 확인하였다.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.52-56
• /
• 2001

This study were looks at the effect of the initial cut length or stress concentration level, on the wave forms produced by crack propagation. The signals were collected, then classified visually for each type of sample. They were put into three classes according to their shapes in the time and frequency domain. Each class should domain signals which could be correlated to a certain micro-failure mechanism that occurs during the fatigue process. Classes of these signals compared, with each sample. To see if there were any classes common to the three samples. The fatigue test attempted to determine if the initial cut length has any influence on the type of signals.

• Composites Research
• /
• v.13 no.1
• /
• pp.61-68
• /
• 2000

A new approach is presented for the analysis of transient waves propagating in anisotropic composite laminates. The wavelet transform (WT) using the Gabor wavelet is applied to the time-frequency analysis of dispersive flexural waves. It is shown that the peaks of the magnitude of WT in time-frequency domain is related to the arrival times of group velocity. Experiments are performed using a lead break as the simulated fracture source on the surface of quasi-isotropic and unidirectional laminates. For predictions of the dispersion of the flexural mode, Mindlin plate theory is shown to give good agreement with the experimental results. Based on the frequency-dependent arrival times and angular dependence of group velocities of flexural waves, the problem of source location in anisotropic laminates is considered and the results are given.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.4 s.175
• /
• pp.1024-1031
• /
• 2000

The plate waves propagating in thin plates have dispersive nature showing the dependence of velocities on the frequency. Wavelet transform (WT) using Gabor function can be used to analyze the dispersive waves in the time-frequency domain, and then to find the arrival time of the waves propagating in the plate. Plate waves in the aluminum plate of 3 mm thickness were identified and generated by pencil lead breaks and the lowest order symmetric ($S_o$) and antisymmetric ($A_o$) modes were analyzed by the WT method. The measured group velocities agreed very well with theoretical predictions in the frequency range of 50-400 kHz. The pencil breaks were also used to simulate acoustic emission sources in the plate, and the source location algorithm using the wavelet transform of dispersive plate waves was found to give accurate results.

• Journal of the Korean housing association
• /
• v.19 no.6
• /
• pp.137-144
• /
• 2008

Public housing problem became a major issue in each European country during the period of the reconstruction. This study focuses on the one of the major institutional policies in the public housing sectors in Europe during the second postwar period, specifically the INA (Istituto Nazionale delle Assicurazioni)-Casa in Italy from 1949 to 1963. Thanks to the financial Aid provided by 'Marshall Plan' of United States government, Italy initiated INA-Casa housing program elaborated and realized by minister of Labour, Amintore Fanfani. He was strongly influenced by catholic socialism and Weberian corporatism, and also had previously written theoretical studies on the subject during the Interwar years. The outcome of this policy had been devaluated for its Keynesian aspect as well as vernacular predominance in the architectural forms. On the contrary, this study focuses on themes such as continuity of politics before and after the Liberation, status of the architects and their will to social engagement, notion of quarter as 'self-sufficient community' and 'residential unit'. These factors will allow to comprehend the complex nature of the reality where different categories were involved to resolve the common housing problem.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.14 no.3
• /
• pp.151-156
• /
• 1994

Exertion has been made to develop high-temperature (about $250{\sim}650^{\circ}C$) immersion ultrasonic sensor for the visualization of objects, temperature measurement, dimensional check, or nondestructive testing of welds under liquid sodium. In this study, the feasibility of the ultrasonic sensor taking advantage of a strip waveguide was confirmed by water-experiment. The lowest order of antisymmetric Lamb wave was used in the frequency range with negligible dispersion. This plate wave was excited in the stainless steel strip waveguide of 1.0mm thickness and 13mm width by the comb-structure transducer of 2.3MHz frequency. Its attenuation coefficient was 1.2dB/m in air and 380dB/m in water. The signal to noise ratio of 25dB was obtained from a planar reflector 270mm away from the beam aperture of $13mm{\times}39mm$ size.