• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.2
• /
• pp.146-152
• /
• 2014

Design procedure of WEC (wave energy converter) using the heaving motion of a floating cylinder-type buoy coupled with LEG (linear electric generator) system is introduced. It is seen that the maximum power can actually be obtained at the optimal conditions ($c_{PTO}=b_T$, ${\omega}={\omega}_N$). Then, based on the developed theory, several design strategies are proposed to further enhance the maximum PTO (power take off), which includes the intentional mismatching with the heave natural frequency, which is 15% higher value than the peak frequency of input velocity spectrum. By using the intentional mismatching strategy, the generated power is actually increased and the corresponding draft as well as the required PTO damping value is significantly reduced, which is a big advantage in manufacturing the WEC with practical LEG (linear electric generator) system.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.20 no.2
• /
• pp.91-99
• /
• 2017

The parametric study was performed for performance enhancement of wave energy converter(WEC) using a submerged pendulum plate. The wave exciting moment and hydrodynamic moment were obtained by means of eigenfunction expansion method based on the linear potential theory, and then the roll response of a pendulum plate and time averaged extracted power were investigated. The optimal PTO damping coefficient was suggested to give optimal extracted power. The peak value of optimal extracted power occurs at the resonant frequency. The resonant peak and it's width increase, as the height and thickness of a pendulum plate increase. The mooring line installed at the end of the pendulum plate is effective for extracting wave energy because it can not only induce the resonance with the waves of the installation site but also increase the restoring moment in case of PTO-on. The WEC using a rolling pendulum plate suitable for the shallow water acts as breakwater as well as energy extraction device.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.282-290
• /
• 2015

In this study, a latching control technology, proposed by Sheng et al.(2015), was applied in order to maximize the extraction efficiency of WEC (Wave Energy Converter), which is the heaving buoy coupled with linear electric generator. The latching control is the phase-control technique for improving the wave energy conversion with appropriate latching duration of keeping the buoy fixed. From the time-domain analysis in regular waves, the latching control technology can significantly improve the heave velocity and extracted power, even though the resonance condition is not satisfied. By using the latching control technology, the draft of buoy as well as the required PTO damping force can be significantly reduced along with increased extracted power, which is a big advantage in manufacturing the WEC.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.254-262
• /
• 2015

Parametric study on submerged body shape of an oscillating hemisphere point absorber was conducted to predict the optimal relation between radius and draft of the body. As an additional damping due to power takeoff system, the optimal damping same as wave radiation damping was applied to the PTO system to produce the maximum wave power. Body response spectrum and power spectrum were obtained for various peak frequencies on wave spectra. It was found that the maximum power can be generated when the peak frequency of available wave power was 20% greater than that of wave spectrum.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.2
• /
• pp.103-111
• /
• 2014

The wave power, extracted from a circular array of small power buoys, is investigated under the potential theory. It is assumed that the buoy's radius, the draft, and the separation distance are much smaller than the water depth, the wave length, and the radius of a circular deployment area. The boundary value problem involving the macro-scale boundary condition on the mean surface covered by buoys is solved using the eigenfunction expansion method. The capture width, which is defined as the ratio of the extracted power to the wave power per unit length of the incident wave crest, is assessed for various combinations of packing ratio, radius of a circular array, and PTO damping coefficient. It is found that the circular array deployment is more effective in the viewpoint of efficiency than the single large buoy of the same total displaced volume.

• Journal of Ocean Engineering and Technology
• /
• v.30 no.5
• /
• pp.361-366
• /
• 2016

The aim of this study was to experimentally investigate the hydrodynamic performance of a hemispheric wave energy converter (WEC) and its wave power takeoff. The WEC is a heaving body-type point absorber with a hydraulic-pump power take-off (PTO) system. The hydraulic PTO system consists of a hydraulic cylinder, hydraulic motor, and generator, with consideration given to the hydraulic pressure and flow rate. Two body model shapes, including the original hemisphere and a bottom-chopped hemisphere, were considered. The heave RAOs of the two models were evaluated for various body drafts. The effects of the hydraulic PTO system on the RAOs were also investigated.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.4
• /
• pp.242-251
• /
• 2020

In this study, the extraction efficiency and reflection coefficient by a two-dimensional OWC (Oscillating Water Column) WEC (wave energy converter) installed in front of a seawall was investigated for regular/irregular waves. The matched eigenfunction expansion method (MEEM) based on the linear potential theory was applied as an analytical tool. The diffraction problem by the incident wave in the open-chamber and the radiation problem by the oscillating pressure in the closed-chamber were solved to obtain the volume fluxes at the internal free-surface. Applying the volume fluxes into the continuity equation for the airflow in a chamber, we got the oscillating air pressure. The maximum extracted power and corresponding reflection coefficient were determined at the optimal turbine coefficient that maximizes the extracted power. OWC device designed for a high extracted efficiency simultaneously contributes to reduce reflected waves.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.65-65
• /
• 2009

본 연구에서는 ICP 식각장치 및 $Cl_2$/Ar 플라즈마에 의한 $Ba_2Ti_9O_{20}$(BTO) 박막의 식각 특성을 고찰하였다. XPS 분석 장치를 이용하여 식각 표면 반응을 조사하였으며, 공정 변수 ($Cl_2$/Ar 가스 혼합비, 소스파워, 챔버 압력, 바이어스 파워)에 따라 플라즈마 특성 변화를 Langmuir probe measuring system을 이용하여 추출하였다. $Cl_2$/Ar 가스에서 Ar 가스의 혼합비가 증가함에 따라 BTO 박막의 식각 속도는 감소하였으며, $Cl_2$ 가스만을 사용하는 경우, 31.7 nm/min 으로 가장 높은 식각 속도를 보였다. Ar 가스의 혼합비에 따른 BTO박막의 식각속도 변화는 Langmuir probe 특성과 XPS 분석결과로부터 플라즈마 내에 형성되는 Cl radical density와 밀접한 관련이 있는 것으로 판단할 수 있다.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.18 no.4
• /
• pp.291-297
• /
• 2015

The wave spectrum was generated from wave data measured at the Chagwi-do site in Jeju, where a 10MW class floating wave-offshore wind hybrid power generation system will be installed. The latching control technology (Sheng et al.[2015]) was applied in order to improve the extracted power from WEC (Wave Energy Converter), which is heaving in corresponding irregular waves. The peak period as a representative value of irregular waves was used when we determined the latching duration. From the numerical results in the time-domain analysis, the latching control technology can significantly improve the extracted power about 50%.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.463-463
• /
• 2011

집속이온빔장치(Foucused Ion Beam)에서 사용하는 액체금속이온원(Liquid Metal Ion Source)은 고 전류밀도, 고 휘도, 낮은 에너지퍼짐 등 많은 장점이 있다. 대부분의 집속이온빔 장치에서 플라즈마 이온소스에 비해 빔의 직경이 작고 GFIS 보다 다루기 쉬워 액체금속이온원을 많이 사용하고 있다. 기존에 사용하던 액체금속이온원에 서프레셔라는 새로운 전극을 추가시켜 팁과 갈륨저장소, 서프레셔, 추출극 구조로 만들었다. 이 연구를 위해 RPA(Retarding Potential Analyser)를 제작 하였다. RPA는 두 개의 메쉬와 하나의 컬렉터로 이루어져 있으며, 액체금속이온과 플로팅 되어있는 RPA에 전압의 차이를 주기위해 베터리로 제작한 파워로 액체금속이온에 인가되는 전압에 + 90V, -90V까지 제어가 가능하게 만들었다. 본 연구에서는 서프레셔의 유무에 따른 액체금속이온원의 에너지 퍼짐에 대해 연구하였다. 추출극에 전압 변화를 주어 방출되는 전류를 5uA, 10uA, 15uA, 20uA로 변화시켜가며 RPA에서 측정되는 전류를 가지고 전류-전압의 관계를 보았고, 에너지 퍼짐정도를 알았다. 마찬가지로 서프레셔에 전압 변화를 주어 전류-전압 관계, 에너지 퍼짐정도를 알았다.