• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.190-195
• /
• 2000

This paper presents the fabrication of the LNA which is operating at 2.13∼2.16 GHz for IMT-2000 lot-end receiver using series feedback and resistive decoupling circuit. Series feedback added to the source lead of a transistor keep the low noise characteristics and drop the input reflection coefficient of amplifier simultaneously. Also, it increases the stability of the LNA. Resistive decoupling circuit is suitable for input stage matching because a signal at low frequency is dissipated by a resistor in the matching network The amplifier consist of GaAs FET ATF-10136 for low noise stage and VNA-25 which is internally matched MMIC for high gain stage. The amplifier is fabricated with both the RF circuits and self bias circuit on the Teflon substrate with 3.5 permittivity. The measured results of the LNA which is fabricated using above design technique are presented more than 30 dB in gain P$\_$ldB/ 17 dB and less than 0.7 dB in noise figure, 1.5 in input$.$output SWR(Standing Wave Ratio).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.1
• /
• pp.49-57
• /
• 2002

The possibility of a transmission noise reduction of piezoelectric smart panels using piezoelectric shunt damping is experimentally studied. Piezoelectric smart panel is basically a plate structure on which piezoelectric patch with shunt circuits is mounted and sound absorbing materials are bonded on the surface of the structure. Sound absorbing materials can absorb the sound transmitted at mid frequency region effectively while the use of piezoelectric shunt damping can reduce the transmission at resonance frequencies of the panel structure. To be able to reduce the sound transmission at low panel resonances, piezoelectric damping using the measured electrical impedance model is adopted. Resonant shunt circuit for piezoelectric shunt damping is composed of register and inductor in series, and they are determined by maximizing the dissipated energy throughout the circuit. The transmitted noise reduction performance of smart panels is investigated using an acoustic tunnel. The tunnel is a tube with square crosses section and a loud-speaker is mounted at one side of the tube as a sound source. Panels are mounted in the middle of the tunnel and the transmitted sound pressure across panels is measured. Noise reduction performance of a smart panels possessing absorbing material and/or air gap shows a good result at mid frequency region but little effect in the resonance frequency. By enabling the piezoelectric shunt damping, noise reduction of 10dB, 8dB is achieved at the resonance frequencise as well. Piezoelectric smart panels incorporating passive method and piezoelectric shunt damping are a promising technology for noise reduction in a broadband frequency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.4
• /
• pp.616-624
• /
• 2006

In this paper, the transfer characteristics of high frequency transmission line having defected ground structure (DGS) and lumped elements are described. When a DGS, which is a kind of periodic structure, is inserted into a transmission line, its equivalent inductance and capacitance elements are added to the characteristics of the standard transmission line. This generates resonance, 3dB cut-off frequency, low-pass, band rejection, and band pass characteristics, and causes a slow-wave and enlarged electrical length of the transmission line. In addition, if the DGS is combined by a lumped element such as resistor, capacitor, and inductor, the resonant and cut-off frequencies moves up or down and other changes occur in the transmission characteristics. The variation of the transmission characteristics is described with the qualitative prediction and measured data.

• Journal of Astronomy and Space Sciences
• /
• v.26 no.2
• /
• pp.229-236
• /
• 2009

KOorea Multi-purpose SATellite(KOMPSAT)-5 will be launched at 550km altitude in 2010. Accurate satellite position(20 cm) and velocity(0.03 cm/s) are required to treat highly precise Synthetic Aperture Radar(SAR) image processing. Ionosphere delay was eliminated using dual frequency GPS data and double differenced GPS measurement removed common clock errors of both GPS satellites and receiver. SAC-C carrier phase data with 0.1 Hz sampling rate was used to achieve precise orbit determination(POD) with ETRI GNSS Precise Orbit Determination(EGPOD) software, which was developed by ETRI. Dynamic model approach was used and satellite's position, velocity, and the coefficients of solar radiation pressure and drag were adjusted once per arc using Batch Least Square Estimator(BLSE) filter. Empirical accelerations for sinusoidal radial, along-track, and cross track terms were also estimated once per revolution for unmodeled dynamics. Additionally piece-wise constant acceleration for cross-track direction was estimated once per arc. The performance of POD was validated by comparing with JPL's Precise Orbit Ephemeris(POE).

• Applied Biological Chemistry
• /
• v.16 no.3
• /
• pp.146-165
• /
• 1973

Crop damages caused by sulfur dioxide poisoning were studied with respect to physiology of lesion, yield loss and prevention measures. The results are summarized as follows; 1. On the physiology of injury: The sulfur dioxide gas did no: affect the pH and $E_h$ values of the tested leaf juice of plants. Peroxidase activity was inhibited just after sulfur dioxide treatment but gradually recovered to normal after 10 hours. Methanolic chlorophyll solution was instantaneously and irreversibly bleached by the addition of sulfur dioxide gas with no evidence of pheophytin formation. It seems that chlorophyll forms colourless addition product or is reduced to colourless form with either sulfur dioxide gas or sulfurous acid. Chlorophyll in the chloroplast was also bleached by the sulfur dioxide treatment, as in the case of methanolic solution of chlorophyll, except that the rate of bleaching was rather slow, requiring 1-2 hours. It appears that the most inflicting cause of sulfur dioxide gas to plants may be the destruction of chlorophyll by the poisoning gas. 2. On the effects to crop yield: The crop yield losses were proportional to the concentration of inflicting sulfur dioxide gas. The order of tolerence of the crops to the sulfur dioxide gas was as follows - chinese cabbage being the most susceptible; wheat, paddy rice, barley, soybean, welsh onion, radish and chinese cabbage. The crucifer crops were generally found more susceptible than other crops studied. With respect to the growing stages of crops exposed to sulfur dioxide gas, it was found that the flowering stage was the most susceptible fellowed by panicle forming, milky and tillering in the decreasing order of susceptibility. 3. On the preventive measures of yield losses: Soil applications of potassium, wollastonite, lime or spray of lime water were effective to prevent yield losses from sulfur dioxide fumigation of paddy rice, barley, and soybeans. The most responsive treatment was lime water spray for all crops tested. In case of sulfur dioxide fumigated paddy rice, the lime water spray also increased carbon assimilation.