• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.715-719
• /
• 2005

현재 우리나라는 1970년대 이후 급속한 경제성장으로 인하여 산업화 및 도시화 현상이 심화되고 있는 실정이며, 이러한 과정에서 불투수층의 증가로 인하여 첨두유출량의 증가, 자연유역에서 도시유역으로 변하면서 유역내 도달시간의 감소 등의 수문학적 특성이 변화로 예기치 못한 홍수로 인하여 피해가 발생하고 있다. 다라서 첨두유출량이 관망으로 전달되는 과정에서 관에 발생하는 부하의 증가로 인하여 내수침수 피해를 입게 되는데, 도시 유역에서의 인구 증가 및 산업활동에 따른 도시 개발로 인한 불투수면적의 증가로 우수유출량이 커지고 있으며, 저지대의 활용이 증대됨에 따라 내수 피해는 더욱 증가되고 있는 실정이다. 이러한 도시 유역의 재배 저감 대책 수립을 위해서는 먼저 실측자료와 도시유출 모형에서 산정된 첨두유출량과의 비교$\cdot$분석하여 최적의 모형을 채택하여야 한다. 또한 채택된 모형으로 적절한 설계 강우량이 선정되어야 하고, 그에 따른 유출량을 정확히 산정하여야 하나, 설계 강우량 산정을 위한 강우의 지속시간의 결정에 대해서 일반적인 기준이 확립되지 못하고 있는 실정이기에 재해 저감 대책 수립에 많은 어려움이 따르고 있다. 이에 본 연구에서는 실측 강우량, 첨두유출량 및 유출총량과 도시지역의 유출량 산정에 사용되어지는 ILLUDAS, SWMM 모형에 모의치와의 비교 연구를 통해 최적의 도시유출모형을 제시하고자 한다. 따라서 실측자료가 있는 서울시 장안$\cdot$뚝섬배수구역의 실측 강우와 펌프장에서 조사된 실측 유량과 ILLUD AS, SWMM 모형에 의해 산정된 유량과의 비교 분석 결과 SWMM 모형에 의한 첨두유량이 실측 첨두유출량과의 오차율에서 장안배수구역은 $21.1\%$, 뚝섬배수구역은 $4.3\%$로 가장 근접한 결과를 나타내었으며, 총 유출량에서도 각각 $7.8\%,\;13.2\%$의 오차율을 가지는 것으로 분석되어 타 모형에 비해 실유량과의 차가 가장 적은 것으로 모의되었다. 향후 도시유출을 모의하는 데 가장 근사한 유출량을 산정할 수 있는 근거가 될 것이며, 도시재해 저감대책을 수립하는데 기여할 수 있을 것이라 판단된다.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.6
• /
• pp.41-47
• /
• 2022

Permeable pavement technology allows the penetration of rainfall into the roadbed, thereby reducing surface runoff and enhancing water quality. The water quality can be improved by adding a filter layer to the permeable pavement. This study analyzes the permeability performance and particulate-matter removal efficiency of a bottom ash-silica sand filter. The performances of five filters with bottom ash and silica sand as the basic materials were evaluated on particulate matter sized 60 ㎛ or smaller. The pure silica sand sample and pure bottom ash sample delivered an average removal efficiency of around 70%. The removal efficiency of the mixed sample was approximately 90%, exceeding the recommended reduction rate (80%) at non-point pollution reduction facilities. In future work, the filter performance should be further verified on permeable pavement.

• Tunnel and Underground Space
• /
• v.20 no.4
• /
• pp.233-240
• /
• 2010

Double Plug is constructed for preventing mixing of two different oils between two compartments in the underground oil storage cavern. And the gas and oil tightness of double plug is tested from the measurement of water leakage from double plug after the completion of double plug water filling. If water leakage is underestimated, it can increase construction cost and if water leakage is overestimated, it can increase operating cost. Therefore, optimum water leakage should be estimated to cut down the cost. In this study, hydraulic stability analysis was conducted to consider permeable properties of rock mass around double plugs and a water leak rate from double plug was estimated from the hydraulic stability analysis and case study. Finally, the reliability of estimation of water leak rate was proven by comparing estimated water leak rate with measured data.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.325-334
• /
• 2003

It is very difficult to rehabilitate the damaged earth dam core to manage it stably against development of flow path and increase of leakage by hydraulic fracture. In this study, application of CGS (Compaction Grouting System) to damaged earth dam core was noticed by analyzing and comparing the results of the in-situ data and FEM. Results of in-situ data showed that according as progress of rehabilitation works tip pressures increased and volume of injection decreased, voids of damaged dam core were filled with materials similar to origin dam core. Rehabilitations caused turbidity and volume of leakage to decrease at the same water level. Also, results of FEM analysis indicated that permeability decreased by rehabilitation. Through this study, it is proved that CGS is able to decrease permeability coefficient, volume of leakage and turbidity on damaged earth dam core.

• Journal of the Korean GEO-environmental Society
• /
• v.25 no.6
• /
• pp.5-12
• /
• 2024

Currently, a grouting method that minimizes damage to the reservoir embankment by injecting solidification agent at low pressure is commonly used to ensure waterproofing and safety of the embankment, but the use of solidification agents can cause issues, such as a decrease in durability and a lack of clear method for determining the mixing ratio. In this study, when the base ground and solidification agent were stirred and mixed at various weight mixing ratios, the permeability coefficient and strength of the mixture were confirmed through laboratory tests, and the optimal mixing ratio was suggested through analysis of the test results. The specimen for the laboratory test was produced considering the mixing ratio of the solidification agent. The specimen for the permeability coefficient test was tested by producing one each of cohesionless and cohesive soil for a mixing amount of 1.5 kN/m³ of solidification agent, and the permeability test results confirmed that the water barrier performance was secured below the permeability coefficient value required by various design criteria. A total of 24 specimens for the strength test were produced, 3 for each of 5 mixing amounts for cohesive soil and 3 mixing amounts for cohesionless soil. The strength test results showed that the uniaxial compressive strength tends to increase linearly with increasing curing time for both cohesionless soil and cohesive soil when the mixing amount is less than 2.0 kN/m³. Therefore, the optimal mixing ratio applied to the site is determined to be mixing amount of 1.5 kN/m³ and 2.0 kN/m³. Finally, numerical analysis reflecting test results was conducted on design case for improvement projects for aging reservoirs embankment to verify the water barrier performance and safety improvement effects.

• The Journal of Engineering Geology
• /
• v.33 no.3
• /
• pp.371-388
• /
• 2023

A stratum with a complex composition and a distributed low-permeability soil layer is difficult to remediate quickly because the soil remediation does not proceed easily. For efficient purification, the permeability should be improved and the soil remediation agent (H₂O₂) should be injected into the contaminated section to make sufficient contact with the TPH (Total petroleum hydrocarbons). This study analyzed a method for crack formation and effective delivery of the soil remediation agent based on pneumatic fracturing, plasma blasting, and vacuum suction (the PPV method) and compared its improvement effect relative to chemical oxidation. A demonstration test confirmed the effective delivery of the soil remediation agent to a site contaminated with TPH. The injection amount and injection time were monitored to calculate the delivery characteristics and the range of influence, and electrical resistivity surveying qualitatively confirmed changes in the underground environment. Permeability tests also evaluated and compared the permeability changes for each method. The amount of soil remediation agent injected was increased by about 4.74 to 7.48 times in the experimental group (PPV method) compared with the control group (chemical oxidation); the PPV method allowed injection rates per unit time (L/min) about 5.00 to 7.54 times quicker than the control method. Electrical resistivity measurements assessed that in the PPV method, the diffusion of H₂O₂2 and other fluids to the surface soil layer reduced the low resistivity change ratio: the horizontal change ratio between the injection well and the extraction well decreased the resistivity by about 1.12 to 2.38 times. Quantitative evaluation of hydraulic conductivity at the end of the test found that the control group had 21.1% of the original hydraulic conductivity and the experimental group retained 81.3% of the initial value, close to the initial permeability coefficient. Calculated radii of influence based on the survey results showed that the results of the PPV method were improved by 220% on average compared with those of the control group.

• The Journal of Engineering Geology
• /
• v.27 no.4
• /
• pp.405-416
• /
• 2017

This study evaluated a model unconfined aquifer comprising a sand or gravel layer, a filter layer, a pumping well, and an observation well. The model was employed in step drawdown tests and then used to assess the permeability of each test tank. The optimal yield and well efficiency were then calculated. Evaluation of yield by step in sand layer filters of equal thickness gave optimized watering rates of 22.03 L/min in the double filter and 19.71 L/min in the single filter. The double filter's yield was 115.0% that of the single filter. A comparison of double and single filters, each 10 cm thick, showed the double filter to have a maximum yield of 182.7%. Yields for the gravel layer were 73.56 L/min for a double filter and 65.47 L/min for a single filter of the same thickness; the former value is 112.3% of that of the latter. Comparison of double and single filters with 10-cm-thick gravel layers revealed that the double filter had a maximum yield of 160.9%. Results for sand wells showed the double filter to have a maximum efficiency of 70.4% and the single filter to have a minimum efficiency of 37.1%. Gravel-layer well efficiencies were >66.5% for both double and single filters (each 30 cm thick), but only 22.5% for a 10-cm-thick single filter. This study confirms that permeability improved as the filter material became thicker; it also shows that a double filter has a higher yield and well efficiency than a single filter. These results can be applied to the practical design of wells.

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.299-306
• /
• 2002

The purpose of this research was to develop a rapid setting cement latex modified concrete (RSLMC) for bridge deck repairing and overlaying. The main experimental variables were latex contents, antifoamer contents and water-cement ratioes. The workability, strength development and permeability were measured as responses. The results showed that latex content increased the slump and reduced the unit water required for same workability. The air contents were measured as 8.0∼9.0％ and 2.0∼3.0％ without antifoamer and with 1.6∼3.2％ of antifoamer, respectively. This resulted in the increment of compressive strength development by 10∼20 ％. The flexural strength of RSLMC increased greatly as the latex content increased, but not in compressive strength. The compressive strength and flexural strength developed enough for opening the overlayed RSLMC to the traffic after 3 hours of RSLMC placement. The permeability of RSLMC was evaluated as negligible due to its very low charge passed. Thus, RSLMC could be used at repairing or overlaying the concrete bridge deck at fast-track job sites.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.457-457
• /
• 2011

저영향개발(LID, Low Impact Development)은 물순환체계 개선을 위해 녹색 공간의 확보, 자연형 공간 조성, 자연상태의 수문순환 기능의 유지 기법 등을 활용한 개발 대상지에서의 강우유출 및 비점오염원의 영향을 최소화할 수 있는 새로운 방법이다. LID는 강우 유출수의 지하침투, 강우 종료시 증발산량의 확보, 강우 유출수의 재이용 등을 통한 강우 유출량을 최소화하는 것에 그 목적이 있다. LID 방법은 우수저류 공원, 생태저류지, 지붕층 저류공원, 보도 저류공간, 인공습지, 완충녹지대, 수목 보존지대, 지붕층 배수관, 강우 저장조, 투수성 포장, 토양 개량, 불투수층 최소화, 비점오염원 저감 등으로 효율성, 경제성, 유연성, 합리성, 토지 가치증대 등의 장점이 있다. 영산강 수계의 BOD 배출부하량이 점오염원(21,019kg/일)과 비점오염원(50,047kg/일)의 비율이 3:7 로 비점오염원 배출부하량이 훨씬 큰 상태이다. 특히, 광주광역시, 농업용 토지, 축산계 등의 비점오염원이 영산강 수질에 크게 영향을 미치고 있다. 따라서 본 연구에서는 비점오염원의 영향이 큰 영산강 수계를 대상으로 앞으로 이루어지는 개발계획을 분석하여 LID 기법을 적용하였을 때 영산강 수질에 미치는 영향을 모델링을 통해 예측하고자 한다. 수질개선에 어느 정도의 효과가 있는지 검증하기 위해 국내 실정에 맞고 QUAL2E 모델을 근간으로 WASP5 모형의 장점들을 접목시켜 Bottle BOD의 반응기작 및 조류의 생산에 의한 유기물 증가, 탈질화 반응 등 정체수역에서 일어날 수 있는 반응기작을 모의할 수 있도록 보완한 QUALKO2 모형을 이용하여 그 효과를 모의하고자 한다. 본 연구를 통해 LID 기법이 도시화에 영향을 얼마나 덜 주는지, 수계의 비점오염원 효과를 통해 물순환 체계의 개선이 어느 정도로 어루어지는지에 대한 효과를 검증을 할 수 있는 계기가 될 수 있을 것으로 판단된다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.498-498
• /
• 2023

정부와 지자체는 기후변화로 인한 홍수 피해를 저감하고자 내수배제 용량 증대, 건전한 물환경 조성 등 다양한 방향의 정책들을 제시하고 있다. 각 지자체 별로 다양한 홍수 대응 정책들을 반영하고 있지만, 2022년 집중호우에 의한 도심지역 침수 피해 사례와 같이 기후변화로 인하여 증가된 홍수량에 대한 적절한 대비를 못하고 있다. 따라서 지자체는 현재의 홍수 대응 정책들과 더불어 추가적인 홍수 대응 정책을 시행하여야 하며, 지속가능한 개발을 고려한 유역의 건전한 물순환을 유지해야 한다. 본 연구에서는 토지피복 등 유역의 특성을 고려하여 실행 가능한 홍수 정책들의 대응 효과를 분석하고, 기후변화 시나리오를 반영한 미래 빈도분석 결과를 반영하여 최적의 홍수 대응 정책 대안을 제시하고자 한다. 연구에서 선정한 홍수 대응 정책은 우수관거 용량을 증대시키는 관거 교체 정책, 지속가능한 저영향개발 기법을 적용한 투수성 포장과 옥상녹화 정책을 선정하였다. 미래 강우 시나리오는 3개의 CMIP6 GCM모형(ACCESS-CM2, CanESM5, GFDL-ESM4)과 2개의 SSP-RCP 시나리오(SSP1-26, SSP5-85)를 사용하였다. 홍수 저감 효과는 도시유출해석모형인 SWMM 모형으로 분석하였다. 또한, 정책 이행에 발생하는 공사와 운영 비용을 산정하여 경제적 편익 분석을 실시하였다. 분석 결과, 투수성 포장과 우수관거 용량 확대 정책을 반영하는 정책 시나리오가 가장 경제적인 홍수 저감 효과를 가져오는 것으로 분석되었다. 본 연구의 정책별 경제적 비용과 홍수 저감 효과 분석은 기후변화에 대비한 도시유역의 홍수 대응 정책을 평가하고 우선순위를 선정하는데 있어 기여 할 수 있을 것으로 기대된다.