• 한국추진공학회지
• /
• 제8권3호
• /
• pp.17-26
• /
• 2004

본 연구에서 동력 전달 시스템은 분리 축 방식의 가스 터빈 엔진의 축 동력을 발전기 전력으로 변환하여, 이것을 프로펠러를 구동하는 추력 모터에 공급하는 방식으로 구성되어있다. 여기에 사용된 가스 터빈 엔진은 엔진 축 마력 317shp(236kw)을 약110kw (147shp)으로 플랫 레이팅(flat rating) 하여 운용한다. 본 시험 장치의 엔진은 가스 터빈엔진 출력축과 발전기 사이에 부하 변화 시 댐핑(damping)역할을 할 수 있도록 플라이 휠(flywheel)을 장착하였다. 이 때 플라이휠의 적절한 관성 모멘트가 고려되지 않으면, 발전기와 모터는 부하 상승에 의한 엔진으로부터 요구되는 출력을 얻을 수 없으며, 또한 엔진이 정상적으로 작동하지 않음을 확인할 수 있다. 따라서 제공된 엔진 데이터와 엔진 시험 데이터로부터 동역학적인 천이 효과에 의한 성능 분석을 함으로써 관성 모멘트의 요구 범위를 결정하였다. 재설계한 플라이휠을 장착 시험한 결과, 본 시스템에서 요구한 출력을 얻을 수 있었다.

• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.78-84
• /
• 1997

Friction welding technique was studied to weld the turbine wheel and shaft of a turbocharger. The welding parameters were selected to investigate the effects of variables on welding quality of Inconel 713C and SCM 440. Experimental results showed that the turbine wheel and shaft could be successfully welded by friction welding. The heat affected zone was identified to be 2 mm from the weld seam. After welding, the hardness profile was found to have sudden increase and decrease for inconel 713C and SCM 440 respectively. Tensile strength of welded specimens was higher than the required strength for all of the studied welding parameters. The central portion of fracture surfaces by bending had no defects such as crack.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1715-1720
• /
• 2004

This paper presents the characteristics of internal clearances for the interstage of blades and shaft gland seals on the steam turbine which are installed in tandem compound. Internal clearances was changed when the rotor turned in the cylindrical sleeve bearing due to the generation of oil film wedge. This presented concern is very useful to prevent the rubbing damage of seal edge between the fixed and moving parts in steam turbine due to the misalignment at the rotating and stationary parts. This method is applied for the unbalanced clearances distribution to the left and right sides in the turbine casing. A considerable amount of unbalanced clearances distribution trend is determined according to the rotating speed of rotor, size and type of proceeding bearing, oil viscosity, surface roughness of bearing and shaft, oil temperature, oil pressure and bearing load.

• 한국자동차공학회논문집
• /
• 제24권6호
• /
• pp.642-648
• /
• 2016

This paper deals with an analytical and experimental investigation to predict the axial thrust load that results from turbocharger operating conditions. The Axial forces acting on the turbocharger thrust bearing are caused by the unbalance between turbine wheel gas forces and compressor wheel air forces. It has a great influence on the friction losses, which reduces the efficiency and performance of high-speed turbocharger. This paper presents the calculation procedure for the axial thrust forces under operating conditions in a turbocharger. The first step is to determine the relationship between thrust forces and strains by experimental and numerical methods. The analysis results were verified by measuring the strains on a thrust bearing with the specially designed test device. And then, the operating strains and temperatures were measured to inversely calculate the thrust strains which were compensated the thermal effects. Therefore it's possible to calculate the magnitudes of the thrust forces under operating turbocharger by comparing the regenerated strains with the rig test results. It will possible to optimize the design of a thrust bearing for reducing the mechanical friction losses using the results.