• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.433-436
• /
• 2010

In this paper, heat/mass transfer characteristics on a film cooled stationary rotor blade are investigated using the naphthalene sublimation method. A row-speed annular wind tunnel with a single annular turbine stage is used. Three rows of film cooling holes are machined on the leading edge of the test blade. Detailed heat/mass transfer distributions are measured with changing the blowing rate from 1.0 to 2.0. As the blowing ratio increases, overall heat/mass transfer increases and the lower peak formed on the pressure side were disappeared.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.4
• /
• pp.275-280
• /
• 2007

A turbine stage consists of stators and rotors. The stator provides the required inlet flow conditions so that the rotor can produce the necessary power. Passing wakes generated from the trailing edge of the stator make an interaction with the rotor. In the present study, this flow mechanism is investigated using the numerical analysis. In case of a large gap distance between the stator and rotor, the flow can be solved independently. First, only the stator flow field is solved. Second, the rotor flow field is solved including the passing wake characteristics obtained from the stator analysis. The passing wake experiences the shearing as it approaches to the rotor blade leading edge. And it is chopped when it strikes the rotor blade. After that, the chopped wakes becomes the prolongation as it travels downstream. The flow according to the variation of the gap distance is also studied. Pressure jumps due to the passing wakes result in the pressure and lift loss and it gets stronger with the closer gap distance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.1
• /
• pp.1-6
• /
• 2008

Performance test of the 30-ton class liquid rocket engine turbopump turbine has been conducted using high pressure cold air. Overall performance of the two kinds of turbine rotors - rotor with knife-edged L.E blades and with rounded L.E blades - has been measured for various rotational speed and turbine pressure ratio. The effect of rotational speed and turbine pressure ratio on the turbine axial force behavior also has been measured in parallel. Test results have revealed that the efficiency of knife edged L.E. turbine is a little bit higher than that of rounded L.E. turbine. The axial force of the turbine varied linearly with respect to rotational speed and its magnitude largely depended on turbine pressure ratio.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.2
• /
• pp.24-31
• /
• 2001

An axial-type turbine design technology is developed. In order to design one-stage turbine, the preliminary design method is applied, and then design parameters are chosen after analyzing gas properties within the turbine passage using the streamline curvature method. Stator blade is designed using C4 profile, and rotor blade is designed using shape parameters. Stator is manufactured as an integral type and rotor is manufactured to be disassembled from the disc for changing blade incidence angle. The output power from the rotor is measured with various RPM and input power. Experimental results show that the maximum efficiency of turbine rotor is obtained on the design point, and the output power is proportionally decreased with the negative incidence angle even the test turbine is a reaction turbine. The efficiency of turbine rotor is decreased to 5% by $7.5^{\cire}$ negative incidence angle from the designed value.

• 열병합발전
• /
• s.63
• /
• pp.8-12
• /
• 2008

• 열병합발전
• /
• s.58
• /
• pp.3-8
• /
• 2007

• 열병합발전
• /
• s.59
• /
• pp.4-8
• /
• 2007

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.9
• /
• pp.889-898
• /
• 2009

A mixed-type turbine was adopted and the rotor outer diameter was 108 mm. Turbine rotors were designed to the axial-type blade because the turbine operated at a low partial admission rate of 1.7-2.0% with two stages. Performance characteristics were studied when the spouting from the nozzle was toward radially inward or outward direction. Additionally, the effect at each stage of the rotor was measured. For comparing with each turbine performance, properties were measured based on various rotational speeds. Measured net specific torque was used to compare with the turbine system performance. On the mixed-type turbine, better performance was obtained when the operating air spouted toward radially inward direction. The specific torque was increased by 7.8% from using the second stage although its effect depended on the rotational speed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.6
• /
• pp.21-29
• /
• 2008

Performance characteristics on a partially admitted small axial-type turbine are experimentally studied with changing design parameters, such as exit flow angles at the nozzle and solidities at the rotor. The tested turbine consists of a single-stage and its mean radius is 35 mm. In this experiment, three different solidities and four different nozzle flow angles are applied to find the optimal design parameter. For a comparison of the turbine performance, the net specific output powers are evaluated. For a 3.4% partial admission rate, the best performance is obtained when the rotor solidity is at 2.18, which is increased to 74% compared to the solidity at full admission.

• KEPCO Journal on Electric Power and Energy
• /
• v.4 no.1
• /
• pp.19-24
• /
• 2018

The long-term research and development for the production of domestic blades has been consistently performed. As the direct and indirect results of its nationwide technologies in precision casting have been improved as well as maintenance costs for turbine machinery has been reduced. Whereas, there are still not a few concerns about the reliability of newly manufactured blades in spite of the quality certificate in metallurgical and mechanical properties. A spin tester is a machine that gives centrifugal loading to a rotating part, and its practical application is the overspeed test that is usually used to check the quality of products. A new spin rig has been constructed in KEPCO Research Institute for the purpose of evaluating the reliability of blades. In this paper, the test methodology for low cycle fatigue damage mechanism as well as the overspeed test for newly developed blades is described, and their reliability is evaluated too.