• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.5
• /
• pp.127-132
• /
• 2009

The transient performance of the passenger diesel engine equipped with the variable geometry turbocharger was simulated using HIL(hardware-in-the-loop) system. The system consists of engine model as software, and the turbocharger test bench as hardware. The engine model is mean value model which is programmed by the Simulink of the Mathworks. The turbocharger test bench is composed of a blower, some sensors, and DAQ boards. A real time simulation is possible since the operating system based on the real time is included. The results show the good response for the transient characteristics. Therefore this HIL system can be used for development of the new turbocharger effectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.711-717
• /
• 2017

Measurements of the moment of inertia of a small turbocharger rotor were studied. A measuring device was manufactured using the trifilar method and the moment of inertia of the calibration rotor was measured to verify the device. The coefficient of variation was 0.43% and the error was 0.75%. The results showed that the device is suitable for measuring the moment of inertia of a turbocharger rotor. Next, the moment of inertia for two turbine rotors and compressor wheels was measured. Those for the turbine rotors showed precise and accurate results in that the coefficients were under 1.0% and the errors were under 3.0%. On the other hand, those for the compressor wheel were precise but inaccurate in that the coefficients were under 1.0% and the errors were over 24.4%. Therefore an indirect method for the compressor wheel was suggested. The results showed that the coefficients were under 1.2% and the errors were under 7.88%.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.726-731
• /
• 2000

This study was experimentally analyzed to improve the performance and to reduce exhaust emissions in a turbochaged D.I. diesel engine of the displacement 9.4L. In generally, the system of intake port, fuel injection and turbocharger are very important factors which have influence on the engine performance and exhaust emission because the properties in the injected fuel depend on the combustion characteristics. The optimum results which is tested as available factors fur better performance and emission are as follows; the swirl ratio is 2.43, compression ratio is 16, combustion bowl is $5^{\circ}$ re-entrant type, nozzle hole diameter is ${\phi}0.28*6$, injection timing is BTDC $13^{\circ}CA$ and turbocharger is GT40 model which are selected compressor A/R 0.58 and turbine A/R 1.19.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.11-22
• /
• 1993

오늘날 자동차용 엔진에 대한 사용자의 요구는 여러가지가 있지만 그 중에서도 손쉬운 운전, 고 출력화, 응답(response)의 향상 등의 요구는 지금 이후로도 계속되리라 생각된다. 슈퍼차저도 이러한 요구에 의하여 사용되고 있으며 이제는 엔진의 보조적 향상책으로 뿐만 아니라 엔진에 있어서 필요 불가결한 것으로써 확실히 정착되리라 생각된다. 본 고에서 살펴본 바에 의하면 스크류식 슈퍼차저가 테스트된 4종류의 슈퍼차저중에서 가장 나은 성능, 과급압, 토르크를 주고 있으며, 또한 가장 소형이며 경량이다. 또한 스크류로타는 팽창기로써 효율 높게 작용할 수 있어, 이의 채용으로 기존의 터보콤파운드시스템 보다 8-10% 에너지 효율이 높게됨이 알려지고 있다. 그러므로 스크류로타를 이용한 터보콤파운드시스템은 기존의 어떤 시스템보다도 효율이 높은 시스템으로 발전할 수 있는 가능성이 높아 이의 연구가 적극 추진되어야 하겠다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.3
• /
• pp.664-675
• /
• 1990

In this study, the performance test and heat transfer experiment for a 4 cylinder and 4-cycle turbocharged gasoline engine were carried out in order to measure the heat transfer coefficient at the inner wall of the combustion chamber. From the result of heat transfer experiment, the energy balance of the fuel energy and the overall efficiency of the turbocharger were calculated, The variation of them was investigated as well with the engine operation conditions.

• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.8-14
• /
• 2013

Hydrogen-natural gas blends(HCNG) engine is optimizing technology of performance and emission characteristics with use of hydrogen's fast flame speed and wide flammability limit. As lean-burn limit is extended, the improvement in thermal efficiency and harmful emissions can be achieved. However, the extension of lean-burn limit under a wide open throttle operation point could be realized with the increase in boosting capacity in a lean-burn engine with turbo-charging system. In the present study, the power output characteristics of HCNG engine with turbo-charger change is assessed and feasibility of the increase in boosting capacity is evaluated. The turbo-charger design with high efficiency at higher flow rate rather than higher boosting pressure makes efficient operation possible at relatively rich mixture condition.

• Journal of the korean Society of Automotive Engineers
• /
• v.5 no.2
• /
• pp.1-14
• /
• 1983

총차량 중량이 15ton이 넘는 대형 트럭의 경우 1970년도에 18%에 불과하던 터보 챠저엔진의 비율은 점차 증가하여 1977년에 42%에 달하였고 1990년도에는 75%까지 증가할 것으로 예상 된다. 또한 현재 터보 챠저엔진의 BMEP는 11.2kg/$cm^{2}$, after cooled엔진은 13.6kg/$cm^{2}$에 이르나 앞으로는 after cooled엔지의 BMEP는 13-17kg/$cm^{2}$로 증대할 것이다. 그러나 터보 챠저엔진의 최대의 단점은 저속에서의 낮은 boost압력과 고속에서의 over boost압력을 갖는다는 것이나, 현재까지는 뚜렷한 해결책을 찾지 못하고 있는 실정이다. 따라서 1980년대에는 현재 사용되고 있는 터보 챠저나 이를 개선한 고성능 터보챠저를 부 착한 엔진이나 after cooled엔진이 주로 사용될 것으로 보인다. 앞으로 터보 챠저가 대형트럭용 엔진에 더욱 확대 사용되고 또 소형 디이젤 엔진이나 가솔린 엔진에서도 이용되기 위해서는 (1) 저속에서의 boost압력 증대 (2) 압력비의 증대 (3) 압축기 사용 flow range의 확대 (4) 소형 터보 챠저의 개발 등이 수반되어야 하며 이외에도 배기가스의 효율적인 에너지전달, 콤푸레샤 효율의 증대, 굉음의 감소, 저렴한 터보 챠저 및 after cooler의 개발, 터보 챠저의 소형화 등이 이루어져야 할 것이다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.3
• /
• pp.796-805
• /
• 1995

For the purpose of improving performances of a turbocharged diesel engine at low speed, this study investigates the effects of the injected air for the performances and flow characteristics in the intake and exhaust pipes by using the computer simulation with test bed. In the theoretical analysis, the whole flow system, including engine cylinders and intake and exhaust pipes, is calculated numerically by the method of filling and emptying. From the results of this study, the following conclusions may be summarized. Increasing injected air pressure into the pipe of compressor exit brings about the improvement in a performance and flow characteristics of intake and exhaust pipes under full load operating conditions at 1000 rpm of the engine speed, but shows trends of the inferior performances under no load operating conditions at 2000 rpm of the engine speed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.11
• /
• pp.4137-4144
• /
• 2010

In this study, the simulations were carried out to show the effect of the EGR configuration in a passenger diesel engine with 2-stage turbocharger on the EGR rate. The AMESim and IFP Engine Library were used to make the program for the simulation. Three EGR configurations, HPL(high pressure loop), LPL(low pressure loop), and SLPL(semi low pressure loop), were considered. The EGR rate in the HPL and LPL EGR routes were 6.4% and 10.0% respectively but the rate in SLPL route was 18.0% and their air/fuel ratio for all three cases was 21. Therefore the SLPL EGR configuration may be positively considered in the design of the passenger diesel engine with 2-stage turbocharger.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.4745-4750
• /
• 2011

A HIL(hardware-in-the-loop) system was established and the simulation was carried out to determine whether the system operates normally. The system consists of turbocharger test bench, HIL platform with real time S/W and DAQ, and engine model using Matlab/Simulink. In the simulation the supplied fuel rate is changed step-by-step from 1.8944 kg/h to 4.7360 kg/h. The change of air-fuel ratio is analyzed and observed whether the air-fuel ratio follow the target air-fuel ratio 32. When the supplied fuel rate is changed, the air-fuel ratio is converged to the target air-fuel ratio after about 20 seconds. And the vane duty ratio of turbine and the boost pressure of compressor are also changed properly. Therefore this HIL system can be used to develop the new turbocharger and improve the performance of the modified turbocharger.